Service manual

1 1 01291 Upper Arm Subassembly
2 1 5345-003 Lever Assembly
3 1 01297 Arm Subassembly
4 1 01293 Step Assembly
5 2 01755 Guide Rod Collet
6 1 01182 Pulley Mount
7 4 PN660201 Hole Plug
8 2 4107M066 Weight Stack Guide Rod
9 1 8640-330 Spiral Pin 10 MM x 90 MM
10 2 PR060005 Weight Bumper
11 2 GP000000 Pulley Assembly
12 4 GP000004 Pulley Spacer
13 2 GP000203 Pulley Center
14 2 HC700415 BHSCS .375-16 x .75
15 2 HN704000 Hex Nut .375-16
16 2 HS348300 Split Lockwasher .375
17 2 HC700414 BHSCS .375-16 x .625
18 2 JC702832 SHCS .375-16 x 2.75
19 2 JC782830 SHCS .50-13 x 2.50
20 1 JN734200 Hex Nut .438-14
21 1 JN734400 Jam Nut .438-14
22 2 PP080204 Plastic Cap .625 ID x .68 OD
23 13 HN784000 Hex Nut .50-13
24 2 JC780420 BHSCS .50-13 x 1.25
25 15 JS388300 Split Lockwasher .50
26 1 JC782832 SHCS .50-13 x 2.75
27 6 JC782836 SHCS .50-13 x 3.25
28 1 01068 Top Weight Assembly
••29 2 4700-019 Flange Bearing
••30 2 BR030206 Retaining Ring
31 1 4700M005 Rubber Cap
32 1 HP286819 Spiral Pin .188 x 1.12
33 1 02224 Modular Screen (not shown)
••34 19 4005C062 Stack Weight 4 x 12
35 4 PP090210 Plastic Insert 2.00 Sq X 10-14 G
36 2 BG030201 Steel Plug
37 4 JC780417 BHSCS .50-13 x 1.00
38 1 HS347700 Washer .375
• 39 1 01419 Stabilizer
• 40 1 HN784000 Hex Nut .50-13
41 Removed
• 42 1 JC782836 SHCS .50-13 x 3.25
• 43 1 JS388300 Split Lockwasher .50
44 2 5580-324 Shim
45 1 01302 Placard Decal
46 1 4000Y316 Caution Decal
47 1 02521 Warning Decal
48 1 4800-381 General Warning Decal
49 2 PR400201 Foam Grip
50 4 4055M028 Foam Grip
51 2 01186 Non-Slip Fabric
52 1 01187 Cable Subassembly
53 1 5310P044 Weight Selector Pin
54 1 PU060204 Bumper
55 1 PU060201 Bumper
56 1 4800-515 Weight Plate Decal
57 2 5345-319 Rubber Grip 7.75
• See Assembly Note #7.
•• FOR UNITS MANUFACTURED PRIOR TO JUNE 1993, CALL 1-888-462-9239.
Assembly Notes
1. Keep all shipping packages near area of installation. Standard shipping items include:
• Assisted Chin Up/Dip Assembly - 5611-9x • Power Assist Package - 5611-50
• Top Weight Package - 01068 (black) • Weight Pack 1 - 4700S040 (black)
• Weight pack 2 - 4700S043 (black) NOTE: x denotes specific color
2. Follow assembly guidelines listed on the 5600 Modular Center Post Assembly & Parts instruction sheet
or the 5629 Tandem Center Post Assembly & Parts instruction sheet. Also refer to all the assembly notes listed below.
3. After installing weight stack, drive spirally coiled pin (item #9) into third weight plate (hole normally used for selector pin).
Be sure pin is flush.
4. After pinning third weight, install foot lever assembly. Rotate lever arm 90 degrees and slide
through column slot from backside of column. Pillow block covers holes 4 - 7 above crossmember.
5. Adjust cable until foot lever arm touches top of slot in column.
6. Verify weight selector pin goes through each hole in the weight stack.
7. Items 39 - 43 are required when the Assisted Chin Up/Dip station is used in Tandem configuration.
See assembly guidelines listed on the 5629 Tandem Center Post Assembly & Parts instruction sheet,
part number 55629.
5611 - Assist Chin Up/Dip
ITEM QTY PART NO. DESCRIPTION
NOTE: This machine shipped with an Owner’s Manual. Additional
copies can be obtained by contacting your dealer or a Cybex
Representative at 1-888-462-9239.
ITEM QTY PART NO. DESCRIPTION