Cybex Treadmill Product Number 770T-CT Owner’s Manual Cardiovascular Systems Part Number LT-22983-4 D www.cybexintl.
Cybex Treadmill Product Number 770T-CT Owner’s Manual Cardiovascular Systems Part Number LT-22983-4 D Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc. Safety Sentry™ is a registered trademark of Cybex International, Inc. Polar® is a registered trademark of Polar Electro Inc. DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual.
Cybex 770T-CT Treadmill Owner’s Manual Table of Contents FCC Compliance Information . . . . . . . . . . 7 Preventive Maintenance Warnings . . . . . . . . . . . . . . . . . . . . . . . . . Regular Maintenance Activities . . . . . . . . Cleaning Your Treadmill . . . . . . . . . . . . . . Running Belt Maintenance . . . . . . . . . . . . Other Preventive Maintenance . . . . . . . . Service Schedule . . . . . . . . . . . . . . . . . . . Safety Important Voltage Information . . . . . . . . . .
Cybex 770T-CT Treadmill Owner’s Manual 6
Cybex 770T-CT Treadmill Owner’s Manual FCC Compliance Information WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Cybex 770T-CT Treadmill Owner’s Manual 8
Cybex 770T-CT Treadmill Owner’s Manual Safety IMPORTANT: Read all instructions and warnings before using the treadmill. Important Voltage Information Before plugging the power cord into an electrical outlet, verify that the voltage requirements for the site match the voltage of the treadmill that has been received.
Cybex 770T-CT Treadmill Owner’s Manual This treadmill is for use on a grounded, dedicated circuit. Make sure that the treadmill is connected to an outlet having the same configuration as the plug. Do not use a ground plug adapter to adapt the power cord to a non-grounded outlet.
Cybex 770T-CT Treadmill Owner’s Manual Facility Safety Precautions • • • • • • • • • • • • • • • • • • • • • • • • • Instruct all users on how to clip the e-stop clip onto their clothing and carefully test it prior to using the treadmill. Instruct all users to use caution when mounting and dismounting the treadmill. Use a dedicated line when operating the treadmill. NOTE: A dedicated line requires one circuit breaker per unit. Connect the treadmill to a properly grounded outlet only.
IN THIS DRAWING IS THE SOLE PROPERTY OF CYBEX. Cybex 770T-CT OR WHOLE WITHOUT CYBEX IS PROHIBITED. REVISIONS Treadmill Owner’s Manual REV DESCRIPTION ECO . See sheet 1 Carefully read and understand the following before using the 770T-CT treadmill: • • Warning Decals Caution Decals To replace any worn or damaged decals do one of the following: Visit www.cybexintl.com to shop for parts online, fax orders to 508-533-5183 or contact Cybex Customer Service at 888-462-9239.
Cybex 770T-CT Treadmill Owner’s Manual DE-22765-4 Warning UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES ARE: .XX ± .02 .XXX ± .010 ANGULAR = ± 1° FINISH = 125 RMS FRACTIONS = ± 1/64” MATERIAL SEE NOTES, Page 1 FINISH SEE NOTES, Page 1 DO NOT SCALE DRAWING 13 ADOBE GENERATED DRAWING DO NOT MANUALLY UPDATE APPROVALS DRAWN BY BGarber CHECKED DATE LABEL, W 650T CON ENGLISH 7/20/10 RESP ENG MFG ENG QUAL ENG SIZE DWG. NO.
Cybex 770T-CT Treadmill Owner’s Manual SOLE PROPERTY OF CYBEX. SOLE PROPERTY OF CYBEX. REV ECO . . Se . . . . . . REV ECO . . Se . . . . . . DE-22910 Warning, 115 VAC Artwork scaled to 80% See above artboard for actual size DE-23079 Warning, 230 VAC Artwork scaled to 80% See above artboard for actual size Do not print an outlin See Solidworks draw UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES ARE: FRACTIONS DECIMALS ANGLES ± .XX ± .02 ± 1 .XXX ± .
Cybex 770T-CT Treadmill Owner’s Manual REVISIONS THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CYBEX. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF CYBEX IS PROHIBITED. REV UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES ARE: .XX ± .02 .XXX ± .010 ANGULAR = ± 1° FINISH = 125 RMS FRACTIONS = ± 1/64” MATERIAL SEE NOTES, Page 1 FINISH SEE NOTES, Page 1 DO NOT SCALE DRAWING DESCRIPTION ECO .
Cybex 770T-CT Treadmill Owner’s Manual 3. Replace the e-stop key. 4. T he treadmill is now ready to be used. NOTE: Ensure the the e-stop clip is secured to your clothing at all times during use. 5. After use, remove the e-stop key from the treadmill. The e-stop key can be removed to help prevent unauthorized use. Refer to the Stopping the Treadmill section in the Operation chapter for more information about the e-stop key.
Cybex 770T-CT Treadmill Owner’s Manual CSAFE Port The CSAFE standard defines a communication protocol and low-voltage DC power source specific to the Fitness Equipment Industry. These RJ-45 phone jacks are provided for use ONLY within the CSAFE protocol. For more information on CSAFE standard, visit www.fitlinxx.com/csafe.
Cybex 770T-CT Treadmill Owner’s Manual This page intentionally left blank.
Cybex 770T-CT Treadmill Owner’s Manual Assembly and Setup Warnings/Cautions All warnings and cautions listed in this chapter are as follows: WARNING: Use extreme caution when assembling the treadmill. Failure to do so could result in injury. WARNING: Failure to correctly install power cord could result in serious injury or death. Ensure the power cord is routed as instructed and does not interfere with the full travel of the elevation system or become pinched by the elevation wheels or treadmill frame.
Cybex 770T-CT Treadmill Owner’s Manual Electrical Power Requirements The power requirements for this treadmill are a grounded, dedicated circuit rated for one of the following: • • • • • • 100 VAC, 50/60 Hz, 20A 115 VAC, 60 Hz, 20A 208 VAC, 60 Hz, 15A 220 VAC, 60 Hz, 15A 230 VAC, 50 Hz, 13A, UK 240 VAC, 50 Hz, 15A Contact a qualified electrician to ensure the power supply complies with local building codes.
Cybex 770T-CT Treadmill Owner’s Manual 2. Verify the following items are present. Check off ( 4 ) each item as you find it. If any of the parts are missing contact Cybex Customer Service.
Cybex 770T-CT Treadmill Owner’s Manual 3. Check off ( 4 ) each item in the hardware pack as you find it. Item 10 15 16 17 18 19 Qty 1 20 2 2 1 1 Part Number HS-21672 HS-22651 FM-22778 FM-22779 HX-00440 FS-23071 Description Screw, #8-32 x 1/2” Bolt, 3/8-16 .
Cybex 770T-CT Treadmill Owner’s Manual CAUTION: A minimum of two people are required to lift, move and assemble this treadmill. Always use proper lifting methods when moving heavy items. Lift and move the treadmill. Take note of doorway widths in facility before assembly. The base is 32.5” (83 cm) wide. With uprights installed the width is 35.6” (90.5 cm). 1. At least two people should lift and move the treadmill to a level location where you intend to leave it. Use proper lifting methods.
Cybex 770T-CT Treadmill Owner’s Manual Back routing: Remove front cover. 1. Using a Philips screwdriver remove the four screws securing the front cover to the base. Front Cover Screws (4) 2. Remove front cover. 3. Using a Phillips screwdriver, remove the two screws securing the right end cap. Right End Cap Screws (2) 4. Remove the right top step by inserting a long 3/8” drive socket extension into the right top step and prying backwards. 3/8” Drive Socket Extension Right Top Step 5.
Cybex 770T-CT Treadmill Owner’s Manual 6. Route the power cord through the hole in the upright support and behind the lower cover. Hole in Upright Support Power Cord Inlet Lower Cover Power Cord 7. Adjust the power cord length entering the frame to allow for the power cord to be plugged into the power cord inlet. Do not plug the power cord in at this time. 8. Adjust the power cord length exiting the rear of the frame. Store extra power cord behind lower cover. 9.
Cybex 770T-CT Treadmill Owner’s Manual Install the uprights. 1. Locate two standoffs short and long. 2. Using a 3/4” open end wrench, secure the standoffs short and long to the right side of the base. Front of Unit Short Long Base 3. Locate the right upright and two bolts. Upright Base Bolt 4. Hand thread two bolts into the base. Do not fully thread bolts into the base. 5. Carefully place the right upright onto the base assembly and the bolts installed in the previous step. 6.
Cybex 770T-CT Treadmill Owner’s Manual Upright Bolt Bolt 7. Repeat steps for the left upright. Install the console assembly to the uprights. 1. Locate the console assembly and two bolts. 2. If unit includes optional A/V or CSAFE cables, follow same display cable procedure. 3. Hand thread one bolt, into the top back hole for each side of the console assembly. Do not fully thread bolts into the console assembly. Console Bolt Upright Display Cable Front of Unit (Right side shown) 4.
Cybex 770T-CT Treadmill Owner’s Manual Display Cable Enters Here Hole 6. Place the console assembly in position on the bolts installed in step 3 in the left and right uprights. 7. Hand thread six bolts, into the remaining holes of the right upright and left upright. Console Upright Bolt (Right side shown) 8. Using the 7/32” Allen wrench, fully tighten all of the bolts. Connect the Display Cable. The display cable and CSAFE cable have the same connectors.
Cybex 770T-CT Treadmill Owner’s Manual 1. Plug the display cable, located at the bottom of the upright assembly into the communication port of the controller. Display Cable (Black) Controller Communication Port CSAFE Cable (Red) Power Supply Cable A/V Cable Install the Power Supply. 1. Locate the power supply, clamp and screw. Power Supply Inlet Clamp AC Cord Gray Cable Clip Screw Console Cable DIN Connector Power Supply Output 2. Secure the power supply to the base using clamp and screw. 3.
Cybex 770T-CT Treadmill Owner’s Manual Install optional A/V or CSAFE cables. The 770T-CT may have A/V or CSAFE cables depending on configuration. 1. Locate the optional A/V cable. 2. Unthread the nut at the end of the A/V cable. A/V Cable Nut 3. Insert the A/V cable into the D-shaped hole into the mounting plate on the front of the unit. Nut Mounting Plate D-Shaped Hole CSAFE Coupler A/V Cable CSAFE Cable (Red) 4. Hand thread the nut removed in step 2 onto the A/V cable. 5.
Cybex 770T-CT Treadmill Owner’s Manual 7. Insert the CSAFE coupler into the mounting plate by hooking the lower tab into the mounting plate and snapping in the upper tab. CSAFE Coupler Upper Tab Mounting Plate Lower Tab Installed 8. Plug the CSAFE cable into the CSAFE coupler on the front of the unit. Install shield. 1. Using a Philips screwdriver install the seven screws securing the shield to the base. Screws (7) Shield Attach the front covers. Perform steps 1 and 2 if you removed the front cover.
Cybex 770T-CT Treadmill Owner’s Manual 3. Locate the motor cover. 4. Place the motor cover into position vertically by aligning the two tabs and four plastic connectors. Two plastic connectors are mounted in the front cover and two in the motor cover. Tabs (2) Motor Cover Plastic Connectors (4) If motor cover top does not fit properly, loosen the side screws on the front cover as needed. 5. Using a Phillips screwdriver, finish tightening the four front cover screws.
Cybex 770T-CT Treadmill Owner’s Manual Attach emergency stop key. 1. Confirm that the emergency stop key is in place in the bottom of the console handrail. The treadmill will not run without the key in place. Emergency Stop Key Console Handrail When not in use store the e-stop clip on the storage tab located under the console handrail. Visually inspect the treadmill. 1. Carefully examine the treadmill to ensure that the assembly is correct and complete.
Cybex 770T-CT Treadmill Owner’s Manual Initial setup Initial setup only occurs during the installation of the unit. Once complete, refer to Setup Options below. 1. At the opening screen press the Cybex logo icon Toolbox and Lock Screen options. to display the Access 2. Press the Access Toolbox icon to display the Access to Toolbox login screen. 3. Enter the sequence: . 4. Press the Setup icon to display the setup menu. 5. Tap the Time icon to advance to the Set the Time screen. 6.
Cybex 770T-CT Treadmill Owner’s Manual The Setup options are: Time and Date Units and Power Workout times Limits Language See Initial setup above See Initial setup above Set Default and Max time Set minimum speed, maximum speed and maximum incline Select language to use for CardioTouch text Exit Set Up Mode. 1. Exit Set Up Mode by tapping the Toolbox icon will refresh. , then tap the Home icon . The screen Your treadmill is now ready for use. Proceed to Testing the Treadmill Operation.
Cybex 770T-CT Treadmill Owner’s Manual 6. Press and hold down the Speed + key until the treadmill reaches a speed of approximately 4 mph (6.4 kph), as indicated on the display. 7. Observe the belt to see that it is running properly; it should stay centered in the middle of the deck. If you have problems with the running belt operation, see Running Belt Adjustments in the Preventive Maintenance chapter. 8. Run the treadmill through its full speed range.
Cybex 770T-CT Treadmill Owner’s Manual Operation Read and understand all instructions and warnings prior to using the treadmill. See all of the safety related information located in chapter 1. Terms Used This section lists some of the common terms and symbols used in this chapter. Other terms and symbols are listed in this chapter as appropriate. For setup options see Setup in Chapter 2. Dormant Mode — This occurs when the treadmill is powered up and not in use.
Cybex 770T-CT Treadmill Owner’s Manual User Control Symbols Used Control Control Name INCLINE UP Description Adjust Incline up. INCLINE DOWN Adjust Incline down. SPEED UP Adjust Speed up. SPEED DOWN Adjust Speed down. VOLUME UP Adjust Volume up. VOLUME DOWN Adjust Volume down. CHANNEL/TRACK CONTROL iPod - NEXT track A/V - Channel UP CHANNEL/TRACK CONTROL iPod - PREVIOUS track A/V - Channel DOWN STOP Press Stop once to end the workout session and start the Workout Review.
Cybex 770T-CT Treadmill Owner’s Manual CardioTouch Symbols Used Icon Icon Name MANUAL QUICK START Description In this active mode the user sets a goal for Time, Distance or Calorie. The user can enter Weight before entering Active Mode. The user controls speed and incline. Manual Mode continues until the goal is reached. Quick Start enters Active Mode at minimum speed and 0% elevation with time counting up from 0:00. PROGRAMS Tap Programs icon to enter program group selection.
Cybex 770T-CT Treadmill Owner’s Manual CardioTouch Symbols Used (continued) Icon Icon Name SHIFT LEFT Description Shift the screen left to view more options. SHIFT RIGHT Shift the screen right to view more options. KEYPAD Numeric keypad for entering data. ENTER Select after entering information to enter value. CLEAR Clear any values selected. INFO Select to provide more information and details. SCALE Displays current value and high/low range.
Cybex 770T-CT Treadmill Owner’s Manual Console Display Bar Graph Heart Rate Indicator Data Readouts Record Indicator Enunciator 41
Cybex 770T-CT Treadmill Owner’s Manual CardioTouch Screen and User Controls Incline Keys Incline Display Volume Keys Speed Display CardioTouch Screen Stop Key Fan Key Speed Keys Channel/Track Keys Displays — Incline and Speed are shown in the LED displays. Keys — User controls for Incline, Speed, Volume, Stop, Fan and Channel/Track. CardioTouch Screen — Tap the icons to make selections.
Cybex 770T-CT Treadmill Owner’s Manual Quick Operation Guide Maximum user weight is 400 lbs. (181 kg). The following is a quick overview of the operation of the treadmill. For more information read Detailed Operation Guide in this chapter. 1. Place your feet on the two top steps located on each side of the running belt. WARNING: Do not stand on the running belt when starting the treadmill. Always place your feet on the two top steps when beginning a workout. 2.
Cybex 770T-CT Treadmill Owner’s Manual Detailed Operation Guide Maximum user weight is 400 lbs. (181 kg). 1. Plug the treadmill power cord into a power outlet from a grounded, single phase, dedicated circuit, rated for one of the following: • • • • • • 100 VAC, 50/60 Hz, 20A 115 VAC, 60 Hz, 20A 208 VAC, 60 Hz, 15A 220 VAC, 60 Hz, 15A 230 VAC, 50 Hz, 13A, UK 240 VAC, 50 Hz, 15A 2. Set the on/off switch to the on position. WARNING: Do not stand on the running belt when starting the treadmill.
Cybex 770T-CT Treadmill Owner’s Manual To select a program, tap one of the program icons from the programs screen. Upon entering a program the display will guide you through the appropriate settings. This is referred to as Program Setup Mode. If the Start key is pressed now, all defaults for that program will be accepted. After 10 seconds, if no key has been pressed, the first default will be accepted. After another 10 seconds the second default will be accepted and so on until the last default.
K RT 1 2 3 Cybex 770T-CT Treadmill Owner’s Manual LEVEL FAN LO 4 5 6 CLEAR ALT ENTER When you adjust incline in a program, the change will affect only the current segment. The program SPEED WEIGHT FAN OFF control will resume starting with the next segment. To increase or decrease overall intensity, adjust 7 8 9 the speed and/or the program level. 10. Press the Speed + – keys to change 0the belt speed at any time. The right display will show the set speed. 11.
Cybex 770T-CT Treadmill Owner’s Manual The emergency dismount: Follow the steps listed below if you experience pain, feel faint or need to stop your treadmill in an emergency situation: 1. Grip handrails for support. 2. Step onto the top steps. 3. Pull the e-stop key off the console. The function of the emergency stop: The e-stop key functions as the emergency stop. In an emergency situation, remove the e-stop key from the treadmill and the running belt will come to a stop.
Cybex 770T-CT Treadmill Owner’s Manual Data Readouts As you exercise, the treadmill keeps track of the following data: Distance — The total accumulated distance, in miles or kilometers, during your workout. Depending on the defaults you’ve chosen this measurement will show in English or Metric. Calories — The total accumulated calories burned during your workout. Your weight must be correctly set before beginning your workout for this measurement to be most accurate.
Cybex 770T-CT Treadmill Owner’s Manual Factors that can interfere with the heart rate signal include: • • • • • • • • excessive movement body composition hydration too loose grip too tight grip running excessive dirt, powder or oil leaning or resting on grips Cybex does not recommend continuous holding onto the contact heart rate grips during exercise. Contaminants, such as hand lotions, oils or body powder, may come off on the contact heart rate grips.
Cybex 770T-CT Treadmill Owner’s Manual Meaning of % Grade A 1% grade is not the same as a 1 degree incline. The % grade is the relationship of the measurement of rise over the measurement of run (also called slope). For example, a 1 foot (meter) rise in height over a length of 100 feet (meters) is a 1% grade. Expressed as a mathematical formula, the grade is calculated as follows: 1 ft. (m) / 100 ft. (m) = 0.
Cybex 770T-CT Treadmill Owner’s Manual Advanced Program Choices: Name Gerkin Protocol Army PFT Air Force PFT Navy PRT Navy PRT Marines PRT Marines PRT One Mile PEB Type Data Entry Results Walk/run Age, weight and gender. 2 mile/3.2 k run Age, weight, gender and starting speed. 1.5 mile/2.4 k run Age, weight, gender and starting speed. 1.5 mile/2.4 k run Age, weight, gender and starting speed. under 5000 feet 1.5 mile/2.4 k run over Age, weight, gender and starting speed. 5000 feet 3 mile/4.
Cybex 770T-CT Treadmill Owner’s Manual • Once a selection is made from the iPod menu, make further selections until the desired media is found.
Cybex 770T-CT Treadmill Service Manual Preventive Maintenance Warnings All warnings listed in this chapter are as follows: WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. WARNING: To prevent electrical shock, be sure that power is shut off and the treadmill is unplugged from the electrical outlet before performing any cleaning or maintenance procedures. WARNING: Keep wet items away from inside parts of the treadmill.
Cybex 770T-CT Treadmill Service Manual WARNING: To prevent electrical shock, be sure that power is shut off and the treadmill is unplugged from the electrical outlet before performing any cleaning or maintenance procedures. After Each Use — Wipe up any liquid spills immediately. After each workout, use a cloth to wipe up any remaining perspiration from the handrails and painted surfaces.
Cybex 770T-CT Treadmill Service Manual CardioTouch Screen — While in Dormant Mode press the Cybex logo icon to access the Lock and Toolbox options. Press the Lock screen for cleaning icon to lock the screen for 10 seconds. The CardioTouch screen will stay locked for 10 seconds to prevent any key presses from being processed. Clean the CardioTouch screen using a soft cloth dampened with a cleaning solution containing rubbing alcohol.
Cybex 770T-CT Treadmill Service Manual Center the belt. The lateral position of the running belt is correctly centered when the Cybex logo is centered between the inside edges of the two belt tracking slots. If the Cybex logo is not centered between the belts tracking slots, center the running belt with the following procedure. 1. With the treadmill running at 5 mph (8 kph) observe the Cybex logo position relative to the belt tracking slots.
Cybex 770T-CT Treadmill Service Manual Inspect the edges of the belt as described below. Tools Required • Phillips screwdriver Disconnect the external power source. 1. Turn the main power switch under the front end of the unit to the off (O) position. 2. Unplug the treadmill from the power outlet. Check the running belt condition. 1. Using a Phillips screwdriver, remove the two screws securing the right end cap. Right End Cap Screws (2) 2. Repeat step 2A for the left end cap. 3.
Cybex 770T-CT Treadmill Service Manual Elevation Motor Lubrication — In time the elevation motor pivot points or tube nut may develop a squeak. Lubricate the upper and lower bolts and the spacers with a small amount of lithium grease. You can buy lithium grease at an auto parts store. Static Electricity — Depending upon where you live, you may experience dry air, causing a common experience of static electricity. This may be especially true in the winter time.
Cybex 770T-CT Treadmill Service Manual Every 5,000 miles (8,000 km). • Check running belt tension and tracking. • Move treadmill and vacuum underneath. • Raise elevation to 15%, carefully roll the treadmill backwards to clean underneath with a dry cloth and vacuum. Return to normal position when done. Every 15,000 miles (24,140 km). • Replace running belt and flip deck. • Check elevation assembly and replace worn parts. • Lubricate elevation pivot points. Every 30,000 miles (48,280 km).
Cybex 770T-CT Treadmill Service Manual This page intentionally left blank 60
Cybex 770T-CT Treadmill Service Manual Customer Service Contacting Service Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard Time. For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239. For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183. Serial Numbers and Voltage The base serial number can be found on the rear of your treadmill.
Cybex 770T-CT Treadmill Service Manual Return Material Authorization (RMA) The Return Material Authorization (RMA) system outlines the procedures to follow when returning material for replacement, repair, or credit. The system assures that returned materials are properly handled and analyzed. Perform the following procedures carefully. Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will request an RMA from Cybex, if applicable.
Cybex 770T-CT Treadmill Service Manual Ordering Parts Online www.cybexintl.com Fax 508-533-5183 Email parts@cybexintl.com Phone 888-462-9239 (for customers living within the USA) 508-533-4300 (for customers outside the USA) CAUTION Use only Cybex replacement parts when servicing. Failure to do so could result in personal injury. All inspections and repairs must be Cybex will void warranty if non-Cybex replacement parts performed by trained service are used. personnel only.
Cybex 770T-CT Treadmill Service Manual This page intentionally left blank 64
Cybex 770T-CT Treadmill Owner’s Manual Appendix A - Technical Specifications Specifications Length: Width: Running Area: Weight of Product: Shipping Weight Speed Range: Incline Range: Manual Mode: Programs: 84” (213 cm). 35.6” (90.5 cm). 22” x 60” (56 cm x 152 cm). 410 lbs. (186 kg). 440 lbs. (200 kg). 0.5 to 12.4 mph (0.8 to 20.0 kph) in 0.1 mph or 0.1 kph increments. 0 to 15% grade. Yes. Quick Start, Manual, and 9 standard programs with user orientated goal (Time, Distance or Calories).
Cybex 770T-CT Treadmill Owner’s Manual This page intentionally left blank 66
