Cybex Arc Trainer 610A Service Manual Cardiovascular Systems May 2004 Cybex and the Cybex logo are registered trademarks of Cybex International, Inc. Polar is a registered trademark of Polar. DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual. We reserve the right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such revisions or changes.
Cybex Arc Trainer 610A Service Manual About This Manual The Service Manual is available in pdf format only. Contact Customer Service at 800-766-3211 or 508-533-4300. To contact Cybex with comments about this manual you may send email to techpubs@cybexintl.com. FCC Compliance Information ! WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Cybex Arc Trainer 610A Service Manual Declaration of Conformity We declare that to the best of our knowledge that the fitness equipment listed below, and manufactured by: Cybex International, Inc.
Cybex Arc Trainer 610A Service Manual Table of Contents Front Pages About this Manual . . . . . . . . . . . . . . . . . . i FCC Compliance Information . . . . . . . . . . i Table of Contents . . . . . . . . . . . . . . . . . . iii 1 Safety Important Voltage Information Grounding Instructions . . . . . Important Safety Instructions Warning Decals . . . . . . . . . . . Caution Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cybex Arc Trainer 610A Service Manual 1 - Safety IMPORTANT: Read all instructions and warnings before using the unit. Important Voltage Information Before plugging the power cord into an electrical outlet, verify that the voltage requirements for your area match the voltage of the unit that you have received. The power requirements for the unit include _ 5%, 50/60 Hz and 15 amps; or 230 VAC a grounded circuit, rated for one of the following: 115 VAC + + _ 10%, 50/60 HZ and 10 amps.
Cybex Arc Trainer 610A Service Manual Important Safety Instructions (Save These Instructions) ! DANGER: To reduce the risk of electric shock, always unplug this unit from the electrical outlet immediately after using it and before cleaning it. ! WARNING: Serious injury could occur if these precautions are not observed. To reduce the risk of burns, fires, electric shock, or injury: User Safety Precautions Safety Page 1-2 • Keep children away. Teenagers and disabled must be supervised.
Cybex Arc Trainer 610A Service Manual Facility Safety Precautions • Make sure all user and safety precautions are observed. • Read and understand the Owner's Manual completely before using the unit. • Make sure all users are properly trained on how to use the equipment. • Make sure that each machine is setup and operated on a solid level surface. Do not install equipment on an uneven surface. • Perform regular maintenance checks on the equipment.
Cybex Arc Trainer 610A Service Manual Warning Decals Carefully read and understand the following before using the unit: NOTE: To replace any worn or damaged decals do one of the following: Visit www.cybexinternational.com to shop for parts online, fax your order to 508-533-5183 or contact Cybex Customer Service at 800-766-3211. If you live outside of the USA, call 508-533-4300. Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
Cybex Arc Trainer 610A Service Manual Underneath Access Cover Warning decal part number - DE-17322-4 Warning decal part number CM000240 CM000240 Safety Page 1-5
Cybex Arc Trainer 610A Service Manual SERIOUS INJURY COULD OCCUR IF THESE PRECAUTIONS ARE NOT OBSERVED High voltage is present under this shield. This shield should only be removed by a qualified service technician. Keep wet items away from inside parts. High voltage may still be present even if the unit is unplugged. Shield part number PL-17237-4 Warning decal part number DE-17155-4 WARNING Hot flywheel! Wait until it cools before servicing.
Cybex Arc Trainer 610A Service Manual Caution Decals Caution decals indicate a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. The caution decals are shown below. CAUTION Moving parts. Keep hands away when in use. DE-17219-4 Caution decal part number DE-17219-4 NOTE: This decal is located on both sides of the unit in a total of two locations.
Cybex Arc Trainer 610A Service Manual This page intentionally left blank Safety Page 1-8
Cybex Arc Trainer 610A Service Manual 2 - Preventive Maintenance Warnings All warnings and cautions listed in this chapter are as follows: ! WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. ! WARNING: To prevent electrical shock, be sure that the power is shut off and the unit is unplugged from the electrical outlet before performing any cleaning or maintenance procedures.
Cybex Arc Trainer 610A Service Manual Cleaning Your Arc Trainer 610A ! WARNING: To prevent electrical shock, be sure that power is shut off and the unit is unplugged from the electrical outlet before performing any cleaning or maintenance procedures. When cleaning your unit spray a mild cleaning agent, such as a water and dish soap solution, on a clean cloth first and then wipe the unit with the damp cloth. NOTE: Do not spray cleaning solution directly on the unit.
Cybex Arc Trainer 610A Service Manual Drive Belt Maintenance There are two drive belts that may become loose, worn or cracked. See Figure 1. Primary Belt - This is the wider of the two belts. It has grooves that keep it aligned on the large upper pulley. Unless the unit has been serviced and not put back together properly, it is unlikely that the primary belt will need to be re-tensioned. Secondary Belt - This is the narrower of the two belts.
Cybex Arc Trainer 610A Service Manual 3. Remove the access cover. Access Cover A. Using a Phillips head screwdriver, remove the four screws securing the access cover in place. See Figure 2. B. Remove the access cover. ! WARNING: The flywheel may be hot. Wait until it cools before servicing. 4. Check the condition of each belt. A. Roll each belt by pulling down on it. Examine the condition of each belt.
Cybex Arc Trainer 610A Service Manual Lubrication The Arc Trainer 610A is designed with no-maintenance parts. Although there are grease fittings on the pillow blocks, re-lubrication of the bearings is not required. Elevation Motor Lubrication - In time the elevation motor pivot points may develop a squeak. If a squeak is present, the unit will need to be serviced by a qualified service technician.
Cybex Arc Trainer 610A Service Manual Service Schedule Preventive Maintenance Page 2-6
Cybex Arc Trainer 610A Service Manual Parts List - Arc Trainer 610A Item Qty 1 1 2 1 3 1 4 2 5 1 6 1 7 1 8 1 9 1 10 1 11 1 12 2 13 4 14 2 15 2 16 4 17 2 18 1 19 1 NA means Not Part Number Varies Varies PL-17209 11090-405 EW600000 EW600006 NA 5610A-4 610A-352 600A-301 YA00022 600A-311 HC700415 HT552515 HX620415 JS347400 PL-16535 BK030205 BK030204 Applicable #7 Description Base with covers attached Console assembly (in box) Water bottle holder (in box) Foot pad (in box) Power cord IEC320 (in box) Power Su
Cybex Arc Trainer 610A Service Manual 4 - Service Warnings/Cautions All warnings and cautions listed in this chapter are as follows: ! WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. ! WARNING: Disconnect the power cord before beginning this procedure. Keep wet items away from inside parts of the unit. Electrical shock could occur even if the unit is unplugged. ! WARNING: Flywheel may be hot.
Cybex Arc Trainer 610A Service Manual ! WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serious injury. For any service related concerns, call Cybex Customer Service at 800-766-3211 (for Cybex customers living within the USA). For customers living outside the USA, call 508-533-4300 or fax 508-533-5183. NOTE: Read and understand each procedure thoroughly before servicing.
Cybex Arc Trainer 610A Service Manual LED Functions LEDs are used to indicate the status of many of the unit inputs. After entering Test Mode refer to the following list to check that these LEDs are functioning properly: Heart LED - Blinks on blue with every signal from the contact heart rate receiver and red for wireless signals (Polar). Weight LED - Blinks on when CSAFE data is being received. Level LED - Blinks on when CSAFE data is being transmitted.
Cybex Arc Trainer 610A Service Manual Error Codes Error codes notify you of a problem condition and are displayed on the center of the console. These codes can also help to indicate the part of the unit most likely to be causing the problem. Errors that present a hazard to the user provide a measure of safety by causing a one second beep, stopping the unit and locking out operation of the unit. A log of errors can be viewed and cleared. Up to 10 errors can be stored.
Cybex Arc Trainer 610A Service Manual Speed Sensor Adjustment Tools Required • Phillips head screwdriver ! WARNING: Disconnect the power cord before beginning this procedure. Keep wet items away from inside parts of the unit. Electrical shock could occur even if the unit is unplugged. Access Cover 1. Disconnect the external power source. A. Turn the main power switch above the power inlet to the off (O) position. B. Unplug the power cord from the power outlet. 2. Remove the access cover. A.
Cybex Arc Trainer 610A Service Manual 5. Adjust the speed sensor gap (if needed). A. Using a Phillips head screwdriver, loosen the screw securing the speed sensor in place. See Figure 3. NOTE: Gently bend the side cover to get at the speed sensor screw. B. Adjust the gap between the speed sensor and the lower pulley to 3/16” (.48 cm) and tighten the screw. See Figure 3. 6. Test for speed errors. A. Connect the power cord to a power outlet. B. Enter Test Mode. ! WARNING: Flywheel may be hot.
Cybex Arc Trainer 610A Service Manual Drive Belts NOTE: This procedure will cover the primary and secondary drive belts.
Cybex Arc Trainer 610A Service Manual 4. Remove the side covers. Gasket Side Cover A. Remove the six screws and six washers securing each side cover in place. See Figure 5. Screw (6) B. Remove both side covers. NOTE: The gasket will come off with one of the side covers. See Figure 5. Washer (6) 5. Remove the crank covers. A. Using a Phillips head screwdriver, remove the three screws securing each crank cover in place. See Figure 6. B. Remove both crank covers.
Cybex Arc Trainer 610A Service Manual NOTE: If you are not replacing the primary belt skip to step 14. Secondary Drive Belt (Removed in Step 7) ! WARNING: Do not touch components on the lower board. A charge can remain after unplugging the power cord and turning off the unit. Lower Pulley 8. Remove the lower board assembly (if applicable). A. Pull out on the lower board shield. See Figure 9. NOTE: It will snap out. Spacer (2) B. Disconnect the elevation motor cable from the lower board. See Figure 10.
Cybex Arc Trainer 610A Service Manual Bolt (4) Pillow Block (2) Pin NOTE: Nuts (4) and flat washers (4) are behind the pillow blocks. Flat Washer (8) Pin Figure 12 B. Remove the crank shaft assembly along with the primary belt, pillow blocks and crank arms out of the unit. NOTE: You may need to wiggle the assembly out. There is a pin in each pillow block. Be sure not to lose them. See Figure 13. Crank Shaft Assembly Primary Drive Belt Washer (8) Pin (2) Nut (4) 10.
Cybex Arc Trainer 610A Service Manual ! CAUTION: Do not pinch your fingers between the belt and pulley during this procedure. 13. Attach the lower board assembly. A. Slide the lower board assembly over the two bottom screws and to the right. B. Using a Phillips head screwdriver, attach the top two screws and tighten the two bottom screws securing the lower board assembly in place. C. Place the washer on the stud then follow it with the ground wire terminal.
Cybex Arc Trainer 610A Service Manual NOTE: Do not adjust the idler pulley unless This Side of it is obvious that your Bracket belt is not tensioned properly. This Side of Bracket Idler Pulley Top Screw Bottom Screw Figure 14 18. Torque the primary belt (if applicable). A. Using a 3/8” square-hole torque wrench, pull up until the idler wheel rocks against the brake and is torqued to 75 ft-lbs. NOTE: Continue holding the torque wrench at 75 ft-lbs during the next step. B.
Cybex Arc Trainer 610A Service Manual B. Using a Phillips head screwdriver, tighten the four screws securing the access cover. See Figure 2. Eddy Current Brake Tools Required • • • • Phillips head screwdriver 3/16” Allen wrench 7/16” Socket wrench Work Gloves ! WARNING: Disconnect the power cord before beginning this procedure. Keep wet items away from inside parts of the unit. Electrical shock could occur even if the unit is unplugged. 1. Elevate the unit and disconnect the power source. A.
Cybex Arc Trainer 610A Service Manual 5. Remove the left crank cover. A. Using a Phillips head screwdriver, remove the three screws securing the left crank cover in place. See Figure 6. Loosen Screws B. Remove the left crank cover. ! WARNING: Failure to release the drive belt tension may cause personal injury and may damage the unit. Lower Pivot Shaft 6. Release the drive belt tension. Figure 15 A.
Cybex Arc Trainer 610A Service Manual B. When the flywheel is cool, remove the secondary belt from the eddy current brake. C. Using a 3/16” Allen wrench, first remove the two bottom screws securing the eddy current brake in place. See Figure 16. D. Support the brake with your hand while removing the two top screws so that it does not fall. E. Remove the eddy current brake from the unit. NOTE: Cybex may want the old parts for evaluation. Call Cybex Customer Service to get an RMA number. 9.
Cybex Arc Trainer 610A Service Manual ! CAUTION: Do not pinch your fingers between the belt and pulley during this procedure. D. Use your hand to slowly turn the flywheel and ensure that the belt is on straight. 12. Attach the left crank cover. A. Place the crank cover in position. B. Using a Phillips head screwdriver, attach the three screws removed in step 5A. See Figure 6. 13. Secure the left side cover. A. Using a Phillips head screwdriver, attach the six screws and six washers removed in step 4A. 14.
Cybex Arc Trainer 610A Service Manual 1. Elevate the unit and disconnect the power source. A. Plug the power cord into the power outlet. B. Enter Test Mode. C. Elevate the unit to a minimum of level 7 incline. D. While the unit is elevated, turn the main power switch to the off (O) position and unplug the power cord from the power outlet. 2. Remove the access cover. A. Using a Phillips head screwdriver, remove the four screws securing the access cover. See Figure 2. B. Remove the access cover.
Cybex Arc Trainer 610A Service Manual 7. Remove the elevation motor. A. Place your body next to the front end assembly to prevent it from pivoting and falling to the floor during the next step. B. Using a 9/16” open end wrench and a 9/16” socket wrench, remove the top bolt and nut securing the elevation motor in place. See Figure 17. NOTE: Do not lose the spacer between the bolt and nut. Spacer Nut Top Bolt 11.37” (28.9 cm) C.
Cybex Arc Trainer 610A Service Manual D. Using a 9/16” open end wrench and a 9/16” socket wrench, tighten a nut on each bolt. 10. Connect the elevation cable. A. Connect the elevation cable to the lower board and place it in the slot mentioned in step 6B. B. Place the lower board shield in position and snap it in. 11. Secure the center cover. A. Place the center cover in position. B. Using a Phillips head screwdriver, attach the two screws removed in step 5A. 12. Secure the side covers. A.
Cybex Arc Trainer 610A Service Manual Power Switch Tools Required • Phillips head screwdriver 1. Disconnect the external power source. A. Turn the main power switch above the power inlet to the off (O) position. B. Unplug the power cord from the power outlet and from the power inlet. 2. Remove the access cover. Screw (2) A. Using a Phillips head screwdriver, remove the four screws securing the access cover. See Figure 2. B. Remove the access cover. 3. Remove the power switch assembly. A.
Cybex Arc Trainer 610A Service Manual To the Controller Brown Blue Brown Blue Brown Blue NOTE: Shown from inside the unit. See the schematic at the end of this chapter for more detail. Green and Yellow Blue Brown Green and Yellow Slots Figure 19 M. Verify the on/off switch is installed properly. See Figure 19. 4. Attach the power switch assembly. A. Place the new power switch assembly into position. See Figure 18. B.
Cybex Arc Trainer 610A Service Manual Upper Pillow Blocks Tools Required • • • • • • • Phillips head screwdriver 3/16” Allen wrench 1/8” Allen wrench 7/16” Socket wrench 9/16” Socket wrench 9/16” Open end wrench 3/8” Nutdriver or socket wrench ! WARNING: Disconnect the power cord before beginning this procedure. Keep wet items away from inside parts of the unit. Electrical shock could occur even if the unit is unplugged. 1. Elevate the unit and disconnect the power source. A.
Cybex Arc Trainer 610A Service Manual 5. Remove the crank covers. A. Using a Phillips head screwdriver, remove the three screws securing each crank cover in place. See Figure 6. B. Remove both crank covers. ! WARNING: Failure to release the drive belt tension may cause personal injury and may damage the unit. 6. Release the drive belt tension. A. Using a 7/16” socket wrench, loosen the two screws on the lower pivot shaft until the screws are raised 1/2” above the shaft. See Figure 15.
Cybex Arc Trainer 610A Service Manual Pin (2) Nut (4) Pillow Block (2) Shaft Set Screws (2 Each Side) Crank Arm Screw (2) Flat Washer (8) Bolt (4) Figure 21 10. Remove the crank shaft assembly. A. Using a 9/16” socket wrench and a 9/16” open end wrench, remove the two bolts, four flat washers and two nuts form each of the top pillow blocks. See Figure 12. B. Remove the crank shaft assembly along with the primary belt and pillow blocks out of the unit. NOTE: There is a pin in each pillow block.
Cybex Arc Trainer 610A Service Manual E. Using a 1/8” Allen wrench, tighten the two set screws on each pillow block. ! CAUTION: Do not pinch your fingers between the belt and pulley during this procedure. 14. Secure the crank arms. A. Slide each crank arm in place. NOTE: The face of each crank arm should be flush with the end of each shaft. B. Using a 7/16” socket wrench, tighten the one screw on each crank arm. 15. Attach the lower board assembly. A.
Cybex Arc Trainer 610A Service Manual B. Using a 3/16” Allen wrench, attach each connecting rod with a screw removed in step 3A. See Figure 4. 21. Attach the access cover. A. While being sure not to pinch any cables, place the access cover in position. B. Using a Phillips head screwdriver, attach the four screws removed in step 2A. See Figure 2. 22. Test the unit for proper operation. A. Connect the power cord into the power outlet. B.
Cybex Arc Trainer 610A Service Manual 3. Detach the connecting rods. A. Using a 3/16” Allen wrench, remove the screw securing each connecting rod to each crank. See Figure 4. B. Place a cloth on the frame where each connecting rod will rest. C. Rest each rod on a cloth to prevent scratches. See Figure 4. 4. Remove the side covers. A. Using a Phillips head screwdriver, remove the six screws and six washers securing each side cover in place. See Figure 5. B. Remove both side covers.
Cybex Arc Trainer 610A Service Manual 7. Secure the side covers. A. Place the two side covers and gasket in position. B. Using a Phillips head screwdriver, attach each side cover with the six screws and six washers removed in step 4A. 8. Attach the connecting rods. A. Place each connecting rod in position. B. Using a 3/16” Allen wrench, attach each connecting rod with a screw removed in step 3A. See Figure 4. 9. Attach the access cover. A.
Cybex Arc Trainer 610A Service Manual Heart Rate Cable Plug Contact Heart Rate Cable Figure 23 4. Remove arm. A. Using a 7/32” Allen wrench remove the two screws and two washers securing the arm to the frame. B. Remove arm from frame. 5. Attach the new arm. A. Slide the (appropriate) arm into the frame. B. Using a 7/32” Allen wrench secure the arm to the frame using the screws and washers removed in step 4A. C.
Cybex Arc Trainer 610A Service Manual 6. Attach the new handle link. A. Slide the handle link onto the arm shaft and foot plate arm shaft. B. Using a Phillips head screwdriver or 3/16” Allen wrench, secure handle link with the screws and (appropriate) cap removed in step 3A. 7. Connect the contact heart rate cable. A. Plug the contact heart rate cable into the plug in the main frame. See Figure 23. Pedal Arm and Foot Plates NOTE: The pedal arms and foot plates are removed in the same way.
Cybex Arc Trainer 610A Service Manual Rear Pedal Arm Front Pedal Arm Foot Plate Small Cap (2) Foot Plate Shafts SHCS (2) Threadlocker Figure 25 Lower Control Board Tools Required • Phillips head screwdriver • 3/8” Nutdriver or socket wrench • ESD (Electro Static Discharge) grounding strap ! WARNING: Disconnect the power cord before beginning this procedure. Keep wet items away from inside parts of the unit. Electrical shock could occur even if the unit is unplugged. 1.
Cybex Arc Trainer 610A Service Manual ! WARNING: Flywheel may be hot. Wait until it cools before servicing. 3. Disconnect the cables from the lower board. A. Pull out on the lower board shield. NOTE: It will snap out. B. Disconnect the cables from the lower board. This includes the elevation motor cable, display cable (P1), AC line 1 (J3 black), AC line 2 (J7 white), eddy current brake cable (J1 and J2) and speed sensor cable (J4). C.
Cybex Arc Trainer 610A Service Manual Lower Control Board Fuses TOOLS REQUIRED • Phillips screwdriver • Needle nosed pliers • Two (2) Fuses, part number EF-12417. 1. Disconnect the external power source. A. Turn the main power switch above the power inlet to the off (0) position. B. Unplug the power cord from the power outlet. ! WARNING: Disconnect the power cord before continuing this procedure. Keep wet items away from inside parts of the unit. Electrical shock could occur even if the unit is unplugged.
Cybex Arc Trainer 610A Service Manual Upper Display Board Tools Required • Phillips head screwdriver • ESD (Electro Static Discharge) grounding strap 1. Disconnect the external power source. A. Turn the main power switch above the power inlet to the off (O) position. B. Unplug the power cord from the power outlet. NOTE: Wear an ESD strap for the rest of this procedure. 2. Remove the console front. A. Using a Phillips head screwdriver, remove the screw securing the access cover to the console back.
Cybex Arc Trainer 610A Service Manual Upper Display Board Upper Switch Membrane Connectors (on front side) Mounting Screws (5) RJ-45 Port Polar connector CSAFE Connector Display Cable Ports Polar Heart Rate Board Ground wire Contact Heart Rate Ports Lower Switch Membrane Connector (on front side) Figure 28 6. Check the connections: A. Check to see that all of the cables are connected firmly in their proper place. 7. Secure the console back. A.
Cybex Arc Trainer 610A Service Manual Upper Display Cable Tools Required • 7/32” Allen wrench • Phillips head screwdriver • ESD (Electro Static Discharge) grounding strap 1. Disconnect the external power source. A. Turn the main power switch above the power inlet to the off (O) position. B. Unplug the power cord from the power outlet. NOTE: Wear an ESD strap for the rest of this procedure. 2. Remove the console front. A.
Cybex Arc Trainer 610A Service Manual 7. Attach the console mount. A. Insert the upper display cable into the console mount and place on top of the base assembly. See Figure 29. Console Assembly Upper Display Cable B. Using a 7/32” Allen Wrench, attach the four screws and four lock washers securing the console mount in place. Washers (4) Lower Display Cable 5. Connect the cables. Screws (4) Contact Heart Rate Cables A.
Cybex Arc Trainer 610A Service Manual 2. Remove the access cover. A. Using a Phillips head screwdriver, loosen the four screws securing the access cover. See Figure 2. B. Remove the access cover. 3. Remove the console assembly. A. Using an Allen wrench, remove the four screws and four lock washers securing the console assembly in place. B. Carefully lift console assembly and disconnect the upper display cable from the lower display cable. See Figure 29. 4. Remove the left wheel. A.
Cybex Arc Trainer 610A Service Manual B. Locate the new contact heart rate cables connected to the lower display cable. The right side cables are located in the outermost locations in the lower display cable connector. See Figure 32. Left Side Heart Rate Wires Right Side Heart Rate Wires C. Tape the new pairs of contact heart rate wires to the old wires cut in step 6A. See Figure 33. NOTE: One brown wire and one black wire make a pair. D.
Cybex Arc Trainer 610A Service Manual Left Contact Heart Rate Cable Right Contact Heart Rate Cable Lower Display Cable To Lower Board Figure 34 NOTE: Frame only shown for cable routing. 10. Attach the left wheel. A. Using a 9/16” wrench and a 3/16” Allen wrench, attach the bolt and nut securing the left transport wheel in position. See Figure 30. Wire Holder Bracket B. Remove the wooden block from under the unit. 11. Test the unit for proper operation. A. Connect the power cord into the power outlet.
Cybex Arc Trainer 610A Service Manual Display Overlays NOTE: This procedure will cover the upper and/or lower display overlay. They are removed and replaced the same. Tools Required • Phillips head screwdriver • ESD (Electro Static Discharge) grounding strap • Razor blade 1. Disconnect the external power source. A. Turn the main power switch above the power inlet to the off (O) position. B. Unplug the power cord from the power outlet. NOTE: Wear an ESD strap for the rest of this procedure. 2.
Cybex Arc Trainer 610A Service Manual B. Place the display board in position and secure with five mounting screws removed in step 2D. C. Place the console front in position and connect these cables to the display board: the display cables; the contact heart rate cables; ground wire and the polar heartrate cable. See Figure 28. 6. Attach the console front. A. While being sure not to pinch any cables, secure the console front to the console back with the four Phillips head screws removed in step 2B. 7.
Cybex Arc Trainer 610A Service Manual Parts List NOTE: Parts lists and exploded views are on the pages that follow.
Cybex Arc Trainer 610A Service Manual Main Assembly ITEM QTY PART NO.
Cybex Arc Trainer 610A Service Manual Foot Plate Arm Assembly Detail Service Page 4-45
Cybex Arc Trainer 610A Service Manual Shroud Assembly Detail Arm Assembly Detail Service Page 4-46
Foot Plate Assembly Detail Drive Frame Assembly Detail Cybex Arc Trainer 610A Service Manual Service Page 4-47
Cybex Arc Trainer 610A Service Manual Console/Console Mount Assembly Service Page 4-48 ITEM QTY B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 C1 C2 C3 C4 C5 C6 1 1 1 1 1 1 1 1 7 4 4 1 1 1 1 2 1 1 1 1 1 4 2 4 4 PART NO.
Console/Console Mount Assembly Detail Cybex Arc Trainer 610A Service Manual Service Page 4-49
Cybex Arc Trainer 610A Service Manual Front End Assembly Service Page 4-50 ITEM QTY PART NO.
Service Page 4-51 Front End Assembly Detail
This page intentionally left blank Service Page 4-52
