USER’S MANUAL Swing-Out Wall Mount Enclosure 12U SAVE THESE INSTRUCTIONS Please read this manual and follow the instructions for installation and use. Copyright © 2016 Cyber Power Systems, Inc. All rights reserved.
Table of Contents Safety Instructions .................................................. 1 Part Identification .................................................... 2 Enclosure Components .....................................................2 Hardware and Accessories ................................................2 Initial Enclosure Setup............................................ 3 Door and Side Panel Locks ...............................................3 Reverse the Enclosure ...........................
Safety Instructions Please read these instructions carefully before use. ● The enclosure is a heavy object. Use of adequate mechanical means to move the enclosure to the desired location is highly recommended to minimize risk of injury or unit damage. For safety reasons, it is highly recommended to handle this unit between two or more people. Use caution when unpacking, moving, and installing the enclosure. Failure to follow may cause serious injury, or unit damage. ● Handle the unit with care.
Part Identification Enclosure Components 3 4 5 2 6 2 1 7 (Model CR12U51001 is shown) 1. Removable, Reversible, and Lockable Front Door 2. Removable and Lockable Side Panels 3. Swing-Out Rear Frame 4. Cable Access with Removable Covers 5. Vents 6. Depth-Adjustable Rack Angles with Dual Mounting Holes 7.
Initial Enclosure Setup CAUTION Setup the following configuration options shown in this section before mounting the enclosure on the wall. Door and Side Panel Locks The front door, rear frame, and side panel locks are keyed-alike. The lock locations are shown below. Use the included keys to operate the locks. NOTE: The enclosure is shipped with the door locked. To access the keys in the accessories bag, open a side panel by pushing the black retention tabs inward as shown on page 5.
Remove and Reverse Front Door 1. Pull on the spring loaded door pin hinges as shown below to remove the door from the enclosure. 2. Remove the door pin supporting washer from the bottom hinge and reinstall it on the opposite door pin hinge. 3. Rotate the front door and reinstall it on the opposite side sliding the door pin hinges into the hinge holes on the enclosure as shown below.
Relocate CyberPower Badge To relocate the CyberPower badge, pull the two parts apart as shown below. To re-install the badge measure the vertical and horizontal distance from the edge of the door as shown below and push both parts together. NOTE: Please press hard to make sure the badge has been firmly installed. 3” (76 mm ) 9.8 4” (25 0m m) Open and Remove Side Panels Unlock the side panel and press the retention tabs simultaneously to release the side panel.
Adjusting Rack Angles Mounting Depth The installed depth of the rack angles can be adjusted by unscrewing them from the horizontal mounting rails. Move the cage nuts behind the upper and lower horizontal rails to the desired depth as shown below. Depth of the rack angles can be adjusted in 3/4” (20mm) increments. NOTE: Verify the rack angles are installed at the correct depth before installing equipment in the enclosure.
To use the side with the threaded holes, unscrew the rack angles from the horizontal mounting rails. Switch the rack angles to the opposite side of the enclosure while ensuring that the rack unit numbers face outward. Screw the rack angles to the horizontal mounting rails. Keep the desired mounting depth when switching the rack angles. Cable Access Cables can be routed through the top or bottom cable openings of the enclosure.
Enclosure Installation The enclosure is a heavy object. For safety reasons, it is highly recommended to WARNING handle this unit between two or more people. Failure to follow these instructions may cause serious injury, or unit damage. Mounting on Wall Before installing the enclosure make sure that the wall is capable of supporting the total load being mounted in the enclosure, including the enclosure itself.
Caster Installation CyberPower's Wall Mount Enclosures are compatible with an optional caster kit (CRA60002) shown below. Please contact your sales representative for ordering information. NOTE: For installation information, please see the CRA60002 quick start guide.
Equipment Installation Verify that the enclosure is securely mounted to the wall prior to installing any equipment in the enclosure. It is strongly recommended to first install equipment in the bottom of the enclosure. Heavier equipment should be installed in the bottom of the CAUTION enclosure. If using sliding rails with installed equipment, use caution when pulling the equipment out of the enclosure as it can cause loading to shift and increase the hazard of tipping or failing.
2. Install the equipment by screwing the included black M6 screws and cup washers into the cage nuts as shown below. 6 5 4 Mounting Using Threaded Round Holes Simply install the equipment by screwing the included silver #12-24 mounting screws into the threaded holes as shown below. 6 5 4 For warranty and additional information, please visit: www.cyberpower.com.
Cyber Power Systems, Inc. www.cyberpower.com For USA and Canada: 4241 12th Ave East, Suite 400 Shakopee, MN 55379 Toll-free: (877) 297-6937 For all other regions: Please visit our website for local contact information. Copyright © 2016 Cyber Power Systems, Inc. All rights reserved.
