LCD-PC i-One Series H5 User Guide
CYBERNET LCD-PC i-One Series H5 2
CYBERNET LCD-PC i-One Series H5 FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CYBERNET LCD-PC i-One Series H5 Safety Instructions Always read the safety instructions carefully. Keep this equipment away from humidity. Lay this equipment on a reliable flat surface before setting it up. The openings on the enclosure are for air convection hence protect the equipment from overheating. DO NOT COVER THE OPENINGS. Confirm the voltage of the power source and adjust accordingly to 110/220V before connecting the equipment to the power inlet.
CYBERNET LCD-PC i-One Series H5 WEEE Statement (Waste Electrical and Electronic Equipment) The WEEE directive places an obligation on EU-based manufacturers, distributors, retailers and importers to take-back electronics products at the end of their useful life. A sister Directive, ROHS (Restriction of Hazardous Substances) compliments the WEEE Directive by banning the presence of specific hazardous substances in the products at the design phase.
CYBERNET LCD-PC i-One Series H5 TABLE OF CONTENTS FCC-B RADIO FREQUENCY INTERFERENCE STATEMENT .............................................................................................. I TRADEMARKS ............................................................................................................................................................ I SAFETY INSTRUCTIONS ..................................................................................................................................
CYBERNET LCD-PC i-One Series H5 INSTALLING THE OPTICAL DISK DRIVE .................................................................................................................................. 19 INSTALLING MINI-PCIE CARDS (OPTIONAL) ......................................................................................................................... 21 INSTALLING THE COVER ................................................................................................................................
CYBERNET LCD-PC i-One Series H5 Introduction Congratulations for purchasing the i-One H5. The i-One Series H5 is your best Slim LCD PC choice. With the fantastic appearance and small form factor, it can easily be set anywhere. The feature packed platform also gives you an exciting PC experience. i-One Series H5 Specifications CPU Support Intel® Core™ i3, i5 and i7 Clarkdale & Lynnfield CPUs up to 1333MHz FSB in an LGA1156 package up to 95W. Motherboard Core Logic Intel® Nehalem PCH H55 chipset.
CYBERNET LCD-PC i-One Series H5 Networking 2 LAN ports, 1Gb (GbE) Fast Ethernet, using Realtek RTL 8111E. Audio HD Audio Codec Realtek® AL889 Flexible 10-channel audio with jack sensing 2 internal stereo speakers, 2.5W, 78dB+/-3dB 3 audio jacks: 1 Audio Out, 1 Line-in, 1 Microphone Compliant with Azalia 1.0 Spec Hard Disk Drive One 2.
CYBERNET LCD-PC i-One Series H5 Operating Environment Ambient Temperature: 0 C ~ 50C (operating) Relative Humidity 10% ~ 90% (non-condensing) Operating System Compliance Microsoft Windows 7, Windows XP, LINUX System BIOS Award Flash BIOS supports ACPI, API, DMI, Plug & Play and Security Password Boots from HDD, PXE, LAN, CD-ROM and any USB device BIOS System POST and BIOS setup password protection TCG/TPM version 1.
CYBERNET LCD-PC i-One Series H5 iOne Series H5 Overview Figure 1: Front View with Optional Webcam Page 4 Overview
CYBERNET LCD-PC i-One Series H5 Figure 2: Left side view with Optical Drive Overview Page 5
CYBERNET LCD-PC i-One Series H5 Figure 3: Power Button and USB Ports 2 Side USB ports Power Button Figure 4: Touch Panel Figure 5: IrDA Receiver for TV Tuner Page 6 Overview
CYBERNET LCD-PC i-One Series H5 On Screen Display Buttons Figure 6: On Screen Display Buttons There are six buttons on the lower right bezel of the screen. From left to right they are: Volume – Volume + Brightness – Contrast + Volume - Press to decrease volume. Volume + Press to increase volume. Mute/Exit Menu/Enter Brightness- Press first to select Brightness adjustment. Press again to decrease brightness. Press Contrast + to increase brightness. Brightness can also be adjusted in Menu Mode.
CYBERNET LCD-PC i-One Series H5 On Screen Display Usage Figure 7: On Screen Display Icons When the Menu button is pressed, the on-screen display appears as pictured above. When in Menu Mode you can move to the various icons with the – (left) or + (right) button. When you are at the icon you wish to adjust, press Menu again (Enter) to change the color of the icon and then toggle your desired adjustment by again pressing either – (left) or + (right).
CYBERNET LCD-PC i-One Series H5 Figure 8: Back View Figure 9: Bottom Panel I/O Ports Overview Page 9
CYBERNET LCD-PC i-One Series H5 Figure 10: CPU Heat Sink Ventilation Fan CPU FAN Figure 11: System Ventilation Fans and Stand System Ventilation Fan System Ventilation Fan Stand Page 10 Overview
CYBERNET LCD-PC i-One Series H5 System Assembly This chapter provides system assembly information and procedures. While performing any installation, use a grounded wrist strap before handling computer components and carefully follow all installation procedures. Static electricity may damage the components. This chapter will include instructions for how to install CPU, heat sink, memory modules, hard disk drive (HDD), optical disk drive (ODD), and mini-PCIe card.
CYBERNET LCD-PC i-One Series H5 Orientation of Key Parts Figure 12: System Fans, CPU Heat Sink Fan and Ventilation CPU Heat Sink Fan and Ventilation System Fan And Ventilation Page 12 System Fan And Ventilation System Assembly
CYBERNET LCD-PC i-One Series H5 iOne Series H5 Disassembly ORIENTATION: Presumes the top of the iOne is away from you and the bottom or I/O controller board is nearest you. Place the iOne face down on a padded surface. Remove the four screws from the base plate that attaches the stand to the LCD supporting the base while removing the last screw. Remove the eleven back bezel screws. Carefully remove the back bezel and set aside.
CYBERNET LCD-PC i-One Series H5 Figure 13: iOne H5 Standard Open System Figure 14: iOne H5G Open System with GPU Page 14 System Assembly
CYBERNET LCD-PC i-One Series H5 Installing the CPU NOTE: If you purchased your iOne Series H5 as a turn-key system, you must first follow the instructions to remove the heat sink in order to be able to reach the CPU. Systems purchased as „bare bones‟ require the installation of the heat sink which is shipped in the accessories box with the unit. 1. The socket has a plastic cap on it to protect the pins from damage. This should remain in place until actually installing a CPU. 2.
CYBERNET LCD-PC i-One Series H5 Installing the CPU Heat Sink 1. Put on the heat sink and make sure that the six screws fit the corresponding holes on the mainboard. 2. Alternate pressure while securing the screws with balance. Note: Do not fix any screws until all six screws are in their positions. 3. Secure the two screws at the opposite end near the top edge of the bezel. 4. Connect the power cable to CPU Fan on the Mainboard labeled CPU FAN 1.
CYBERNET LCD-PC i-One Series H5 Installing the Memory Module DDR3-SO-DIMM 1. The memory module has only one notch and will only fit in the slot one way. 2. Insert the memory module into the DIMM slot at a 45° angle. Then, push it in until the golden finger on the memory module is deeply inserted in the DIMM slot. 3. Press the memory module down and the metal clip at each side of the DIMM slot will automatically close. 4. Repeat the steps to install another memory module to meet your needs.
CYBERNET LCD-PC i-One Series H5 Installing the Hard Disk Drive 1. Mount the brackets to both sides of the hard disk drive with four screws 2. Mount the hard disk drive in the bracket onto the frame of the unit lining up and securing the four screws. 3. Connect the SATA cable & the Power cable to the mainboard. 4. Connect the other end of the SATA/Power to the hard Disk Drive as shown.
CYBERNET LCD-PC i-One Series H5 Installing the Optical Disk Drive 1. Remove back bezel as indicated in iONE Disassembly. Remove the Optical Disk Drive frame. 2. Put the ODD on the ODD frame and line up the four screw holes accordingly. 3. Secure the four screws on the ODD frame.
CYBERNET LCD-PC i-One Series H5 4. Connect the SATA cable. Connect the Power Cable. 5. Connect the other end of the cable to the ODD. 6. Install the ODD frame and line up the two screw holes over the Metal support. 7. Secure the two screws to fix the ODD frame and complete the installation.
CYBERNET LCD-PC i-One Series H5 Installing Mini-PCIe Cards (Optional) 1. Mini-PCIe cards have only one notch and will only fit into the slot one way. Insert the mini-PCIe cards into the mini-PCIe slots at a 45° angle. Then, push in until the golden fingers on each mini-PCIe card are deeply inserted in the mini-PCIe slots. 2.
CYBERNET LCD-PC i-One Series H5 Installing the Cover 1. Connect the power cables from both System Fans to the mainboard BEFORE securing the metal cover and I/O plate with 18 screws. 2. Secure the plastic cover with eleven screws. 3. Secure the stand with four screws.
CYBERNET LCD-PC i-One Series H5 System Assembly Page 23
CYBERNET LCD-PC i-One Series H5 Page 24 System Assembly
CYBERNET LCD-PC i-One Series H5 Cybernet e-recycling SOP Cybernet has an e-recycling program that is very easy to use. Just follow the steps explained below or go to our website at www.cybernetman.com. 1. Request an RMA via phone, email or support request. 2. We will arrange a call tag to have the product picked up. Just have it packed and ready to ship.
