3COM VCX PBX Server VoIP Intercom Setup Guide CyberData Corporation • 2555 Garden Road • Monterey, CA • 93940 • T:831-373-2601 • F: 831-373-4193 www.CyberData.
1.0 Setup Diagram Figure 1 is a setup diagram for a single Intercom configuration. In this configuration, the Intercom acts as a standalone SIP telephony device. Figure 1.
2.0 Host Environment Table 1. Host Environment Details Description Hardware Type 3COM VCX V7000 Hardware Version Software Type Software Version 3.0 Test Setup Equipment Table 2. Test Setup Equipment Equipment Model Grandstream BudgeTone-100 Version Notes: NetGear EtherFast FS108P Fast Ethernet Switch Notes: VoIP Intercom 010935B 3.3.
4.0 Setup Procedure 4.1 VCX Configuration Below are the steps to configure the VCX so that a CyberData Intercom is able to register with the VCX. To configure the VCX, 1. Navigate to the Central Management Console of the VCX and login as Admin. See Figure 2. Figure 2.
2. Click on the Site Name. Figure 3. Site Name 3. This takes you to the Users page by default. Go to the Phones web page to create an extension for each CyberData Intercom. Figure 4.
4. Select Add Phone and enter phone information. The extension and password assigned here are later used on the SIP Setup web page (Table 3 or Step 5 of Section 4.2, "Setup CyberData Device Parameters"). Figure 5. Add Phone “SIP Setup” web page “SIP Setup” web page 5. Return to the Users page and then select the Add User button to create a user to assign the Intercom extensions to. Figure 6. Users Page VoIP Intercom. VoIP Intercom .
6. Enter information similar to the information shown in Figure 7. Figure 7. Edit User Page VoIP Intercom VoIP Intercom 7. Click the Save button and the screen will go back to the Users web page. 8. On the Users page, look to the far right of the User created for the CyberData Intercoms, and you will see a Phones button (see Figure 6). Use this button to assign and associate Intercom extensions to this user. Note Server Setup Guide There is another Phones menu on the left-hand pane.
9. Click this button to display a list of Extensions associated with this user. Initially this is blank. Figure 8. User—Assigned Phones Page VoIP Intercom 10. Select the Assign Phone button to list all of the available extensions. The web page shown in Figure 9 is now displayed. You may select one or more extensions to assign to this user.
11. To assign multiple extensions, put a check mark on each box next to the extension. 12. Click the Assign Selected button, and all of the marked selected extensions are now associated with this user. Figure 9.
4.2 Setup CyberData Device Parameters To setup CyberData device parameters, 1. Log into the CyberData Configuration Home page (Figure 10) by pointing your browser to the Intercom’s IP address. Figure 10. CyberData Home Page 2 SIP Setup button For the initial configuration of the Intercom, refer to the Operation Guide of the Intercom that you have which can be found at the following web address: http://www.cyberdata.net/support/download.
3. On the CyberData Home Page (Figure 10), click on the SIP Setup button. This will take you to the SIP Setup page (Figure 11). Figure 11.
4. For a quick summary of all of the necessary settings on the SIP Setup page (Figure 11), see Table 3. For a step-by-step description of the necessary settings, go to Step 5. Note If a setting parameter is not listed in Table 3 or Step 5, then your input for that setting parameter is not required. Table 3. SIP Setup Page Settings SIP Setup Page Items Setting SIP Server Type the address of the VCX. SIP User ID Type the phone extension used in Step 4 of Section 4.1, "VCX Configuration".
7. After clicking on the Save Settings button, a reboot timer countdown will begin. Figure 12. Reboot Timer 8. After the Intercom reboots, the green Status LED will blink at one second intervals to indicate normal operation. Note If Yes is selected for Speaker Beep After Initialization on the Setup page of the Intercom (not shown), you will hear a tone after the initialization sequence is complete. 9.
