The IP Endpoint Company VoIP V2 Speaker Operations Guide Part #011098*, RAL 9002, Gray White, Standard Part #011099, RAL 9003, Signal White, Optional *Replaces #011021 Document Part #930274R for Firmware Version 6.3.
VoIP V2 Speaker Operations Guide 930274R Part # 011098* Part # 011099 *Replaces 011021 COPYRIGHT NOTICE: © 2014, CyberData Corporation, ALL RIGHTS RESERVED. This manual and related materials are the copyrighted property of CyberData Corporation. No part of this manual or related materials may be reproduced or transmitted, in any form or by any means (except for internal use by licensed customers), without prior express written permission of CyberData Corporation.
Revision Information Revision 930274R, which corresponds to firmware version 6.3.0, was updated on April 4, 2014 and has the following changes: Operations Guide • Adds the following warning to the following sections: • Important Safety Instructions • Section 1.2, "Installation" • Section Appendix A:, "Mounting the Speaker" • Warning Text: “The PoE connector is intended for intra-building connections only and does not route to the outside plant.
Pictorial Alert Icons GENERAL ALERT General Alert This pictoral alert indicates a potentially hazardous situation. This alert will be followed by a hazard level heading and more specific information about the hazard. Ground This pictoral alert indicates the Earth grounding connection point. Hazard Levels Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This is limited to the most extreme situations.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Abbreviations and Terms Abbreviation or Term Definition A-law A standard companding algorithm, used in European digital communications systems to optimize, i.e., modify, the dynamic range of an analog signal for digitizing. AVP Audio Video Profile Cat 5 TIA/EIA-568-B Category 5 DHCP Dynamic Host Configuration Protocol LAN Local Area Network LED Light Emitting Diode Mbps Megabits per Second. NTP Network Time Protocol PBX Private Branch Exchange PoE Power over Ethernet (as per IEEE 802.
i Contents Chapter 1 Product Overview 1 1.1 How to Identify This Product .....................................................................................................1 1.2 Installation ................................................................................................................................2 1.3 Product Features ......................................................................................................................3 1.4 Supported Protocols .....................
C.4.4 Return and Restocking Policy ......................................................................................74 C.4.5 Warranty and RMA Returns Page ...............................................................................
1 1 Product Overview The CyberData SIP-enabled V2 Speaker is a Power-over-Ethernet (PoE 802.3af) and Voice-over-IP (VoIP) public address loudspeaker that easily connects into existing local area networks with a single CAT5 cable connection. The speaker is compatible with most SIP-based IP PBX. In a non-SIP environment, the speaker is capable of receiving broadcast audio via multicast. Its small footprint and low height allows the speaker to be discretely mounted almost anywhere. 1.
Product Overview 2 Installation 1.2 Installation Note Prior to installation, create a plan for the locations of your speakers. Warning Electrical Hazard: The VoIP V2 Speaker enclosure is not rated for any AC voltages. GENERAL ALERT Warning Electrical Hazard: This product should be installed by a licensed electrician according to all local electrical and building codes.
Product Overview 3 Product Features Figure 1-2 illustrates a typical configurations for the VoIP V2 Speaker. Figure 1-2. Typical Installation 802.3af Compliant Ethernet Switch 1 Speaker Speaker 2 3 4 5 6 IP Phone Clock Kit IP PBX Server See the following sections for other installation options: • Section 2.2.1.3, "Running the V2 Speaker with Auxiliary Power" • Section 2.2.2.1, "V2 Speaker with an External Device" • Section 2.2.2.
Product Overview 4 Supported Protocols 1.4 Supported Protocols The V2 Speaker supports: • SIP • Multicast • HTTP Web-based configuration Provides an intuitive user interface for easy system configuration and verification of speaker operations. • DHCP Client Dynamically assigns IP addresses in addition to the option to use static addressing. • HTTP TCP Post auto-updating event notification in XML format • TFTP Client Facilitates hosting for the configuration file for Autoprovisioning.
Product Overview 5 Product Specifications 1.6 Product Specifications Table 1-1. Product Specifications Category Specification Audio sensitivity 96dB/1W/1M S.P. Level Audio output 10 Watts Peak Power Operating temperature -30 to 55 C (-22 to 131 F) Ethernet port baud rate 10/100 Mbps Protocol SIP RFC 3261 Compatible Power Input (J1) PoE 802.3af (as per IEEE 802.
Product Overview 6 Optional Connections (J9 and J10) 1.7 Optional Connections (J9 and J10) Figure 1-3. Optional Connections (J9 and J10) Function J10 Connections *Auxiliary power input for use when PoE power is not available. 12 VDC @ 1A. AUX POWER (+) (+12VDC @ 1A) AUX SPEAKER (-) AUX POWER (-) AUX SPEAKER (+) Relay contacts rated at 30 VDC @ 1A. 5 VDC @ 100 mA. J9 Connections RELAY COM Function Auxiliary 8-Ohm speaker connection (not to be used when the Clock is connected.
7 2 Installing the VoIP V2 Speaker 2.1 Parts List Table 2-1 illustrates the parts for each speaker and includes kits for the drop ceiling and drywall mounting. Note The installation template for the V2 Speaker is located on the Installation Quick Reference Guide that is included in the packaging with each speaker. Table 2-1.
Installing the VoIP V2 Speaker 8 Device Configuration 2.2 Device Configuration Set up and configure each speaker before you mount it. CyberData delivers each speaker with the following factory default values: Table 2-2. Factory Network Default Settings—Default of Network Parameter Factory Default Setting IP Addressing DHCP a IP Address 10.10.10.10 Web Access Username admin Web Access Password admin Subnet Mask Default a 255.0.0.0 Gatewaya 10.0.0.1 a.
Installing the VoIP V2 Speaker 9 Device Configuration 2.2.1 Connect Power to the Speaker Figure 2-1 through Figure 2-3 illustrates how to connect power to the VoIP V2 Speaker. 2.2.1.1 VoIP V2 Speaker to a 802.3af Compliant PoE Switch Figure 2-1 illustrates how to connect the VoIP V2 Speaker to a 802.3af compliant PoE switch via a Cat 5 Ethernet cable. Figure 2-1. VoIP V2 Speaker to a 802.3af Compliant PoE Switch Cat 5 Ethernet cable 802.
Installing the VoIP V2 Speaker 10 Device Configuration 2.2.1.2 VoIP V2 Speaker (with PoE Injector) to a 802.3af Compliant PoE Switch In Figure 2-2, if a PoE switch is not available, you will need a PoE Injector, part #010867A (ordered separately). A PoE Injector is a power supply solution for those who have a standard Non PoE Switch. Figure 2-2.
Installing the VoIP V2 Speaker 11 Device Configuration 2.2.1.3 Running the V2 Speaker with Auxiliary Power In Figure 2-3, the power for the V2 Speaker can either come from an 802.3af Network connection or from an external source. Caution GENERAL ALERT Operational Note: Do not connect an auxiliary power supply when the V2 Speaker is connected to a PoE power source through J1. Improper operation or equipment damage may occur. Figure 2-3.
Installing the VoIP V2 Speaker 12 Device Configuration 2.2.2 Installation Options This section shows various installation options for the V2 Speaker. 2.2.2.1 V2 Speaker with an External Device In Figure 2-4, when the V2 Speaker is called from a remote phone, the relay on the speaker can be programmed to drive an external device such as an alert strobe. This external device may also be addressed from a separate Unified Communication (UC) server. Figure 2-4.
Installing the VoIP V2 Speaker 13 Device Configuration 2.2.2.2 V2 Speaker with Auxiliary Speaker Connection In Figure 2-5, the V2 Speaker supports an amplified audio output for a second analog speaker. While the total speaker wattage is the same, by connecting a low cost analog speaker, additional coverage can be realized.
Installing the VoIP V2 Speaker 14 Device Configuration Figure 2-6. Clock Kit with Extra Speaker Connection is NOT ALLOWED.
Installing the VoIP V2 Speaker 15 Device Configuration 2.2.2.3 V2 Speaker with Line Out In Figure 2-7, for areas that require more speaker volume, the V2 Speaker can be connected directly to an auxiliary amplifier to drive additional horns or speakers. This is done through the line-out connection. Figure 2-7. V2 Speaker with Line Out Speaker Office area in Factory AUX POWER (+) (+12VDC @ 1A) Line Out: Output Signal Amplitudes 2.0 VPP maximum Output Level +2dBm nominal Total Harmonic Distortion 0.
Installing the VoIP V2 Speaker 16 Device Configuration 2.2.3 Confirm that the Speaker is Operational and Linked to the Network After connecting the speaker to the 802.3af compliant Ethernet hub, the LEDs on the speaker face confirm that the speaker is operational and linked to the network. Figure 2-8. Status and Activity LEDs Network Link/Activity (Yellow) Speaker Status (Green) 2.2.3.1 Status LED After supplying power to the speaker: 1.
Installing the VoIP V2 Speaker 17 Device Configuration 2.2.4 Confirm the IP Address and Test the Audio 2.2.4.1 Reset Test Function Management (RTFM) Button When the speaker is operational and linked to the network, use the Reset Test Function Management (RTFM) button (Figure 2-9) on the speaker face to announce and confirm the speaker’s IP Address and test that the audio is working. Note Using the RTFM button will lock the digital volume level to 4 and disable the analog volume control dial. Figure 2-9.
Installing the VoIP V2 Speaker 18 Device Configuration 2.2.5 Adjust the Volume To adjust the speaker volume, turn the Volume control dial (Figure 2-10) on the speaker face. Note The V2 Speaker has two volume controls: Internal (web-based) and External (volume knob). The external volume control can be disabled from the web interface by selecting Use Digital Volume Control on the Device Configuration Page (see Section 2.3.4, "Configure the Device Parameters"). Figure 2-10.
Installing the VoIP V2 Speaker 19 Device Configuration 2.2.6 How to Set the Factory Default Settings 2.2.6.1 RTFM Button When the speaker is operational and linked to the network, use the Reset Test Function Management (RTFM) button (Figure 2-11) on the speaker face to set the factory default settings. Figure 2-11. RTFM Button RTFM button To set the factory default settings: 1. Press and hold the RTFM button for more than five seconds. 2.
Installing the VoIP V2 Speaker 20 Configure the Speaker Parameters 2.3 Configure the Speaker Parameters To configure the speaker online, use a standard web browser. Configure each speaker and verify its operation before you mount it. When you are ready to mount a speaker, refer to Appendix A, "Mounting the Speaker" for instructions. 2.3.
Installing the VoIP V2 Speaker 21 Configure the Speaker Parameters 2.3.2 V2 Speaker Web Page Navigation Table 2-4 shows the navigation buttons that you will see on every V2 Speaker web page. Table 2-4. V2 Paging Amplifier Web Page Navigation Web Page Item Description Link to the Home page. Link to the Device Configuration page. Link to the Networking page. Link to go to the SIP Configuration page. Link to go to the Nightringer page. Link to the Multicast Configuration page.
Installing the VoIP V2 Speaker 22 Configure the Speaker Parameters 2.3.3 Log in to the Configuration Home Page 1. Open your browser to the V2 Speaker IP address. Note If the network does not have access to a DHCP server, the device will default to an IP address of 10.10.10.10. Note Make sure that the PC is on the same IP network as the V2 Speaker.
Installing the VoIP V2 Speaker 23 Configure the Speaker Parameters 2. When prompted, use the following default Web Access Username and Web Access Password to access the Home Page (Figure 2-12): Web Access Username: admin Web Access Password: admin Figure 2-12.
Installing the VoIP V2 Speaker 24 Configure the Speaker Parameters 3. On the Home Page, review the setup details and navigation buttons described in Table 2-5. Table 2-5. Home Page Overview Web Page Item Description Device Settings Device Name Shows the device name (25 character limit). Change Username Type in this field to change the username (25 character limit). Change Password Type in this field to change the password (19 character limit).
Installing the VoIP V2 Speaker 25 Configure the Speaker Parameters 2.3.4 Configure the Device Parameters 1. Click the Device Configuration button to open the Device Configuration page. See Figure 2-13. Figure 2-13.
Installing the VoIP V2 Speaker 26 Configure the Speaker Parameters 2. On the Device Configuration page, you may enter values for the parameters indicated in Table 2-6. Table 2-6. Device Configuration Parameters Web Page Item Description Volume Settings Use Digital Volume Control When selected, you can bypass the analog volume knob on the front of the speaker. The volume level will only be determined by the digital Speaker Volume setting on the Device Configuration page.
Installing the VoIP V2 Speaker 27 Configure the Speaker Parameters 2.3.5 Configure the Network Parameters 1. Click the Networking button to open the Network Configuration page (Figure 2-14). Figure 2-14.
Installing the VoIP V2 Speaker 28 Configure the Speaker Parameters 2. On the Network Configuration page, enter values for the parameters indicated in Table 2-7. Table 2-7. Network Configuration Parameters Web Page Item Description Stored Network Settings Shows the settings stored in non-volatile memory. IP Addressing* Select either DHCP IP Addressing or Static IP Addressing by marking the appropriate radio button. If you select Static, configure the remaining parameters indicated in Table 2-7.
Installing the VoIP V2 Speaker 29 Configure the Speaker Parameters 2.3.6 Configure the SIP Parameters 1. Click SIP Config to open the SIP Configuration page (Figure 2-15). Note For specific server configurations, go to the following website address: http://www.cyberdata.net/support/server/index.html Figure 2-15.
Installing the VoIP V2 Speaker 30 Configure the Speaker Parameters 2. On the SIP Configuration page, you may enter values for the parameters indicated in Table 28. Table 2-8. SIP Configuration Parameters Web Page Item Description Enable SIP Operation Enables or disables SIP operation. SIP Settings SIP Server Use this field to set the address (in dotted decimal notation or as a canonical name) of the SIP registrar. This field can accept canonical names of up to 255 characters in length.
Installing the VoIP V2 Speaker 31 Configure the Speaker Parameters Table 2-8. SIP Configuration Parameters (continued) Web Page Item Description Beep on Page When selected, the device will play a beep before a page is sent on SIP pages (works for both buffered and live pages). Call Disconnection Terminate call after delay (in seconds) Type the desired number of seconds that you want to transpire before a call is terminated. Note: A value of 0 will disable this function.
Installing the VoIP V2 Speaker 32 Configure the Speaker Parameters 2.3.7 Configure the Night Ringer Parameters 1. Click on the Nightringer button to open the Nightringer Configuration page. See Figure 2-16. Figure 2-16.
Installing the VoIP V2 Speaker 33 Configure the Speaker Parameters 2. On the Nightringer Configuration page, enter values for the parameters indicated in Table 2-9. Table 2-9. Nightringer Configuration Parameters Web Page Item Description Enable Nightringer When the nightringer is enabled, the ceiling speaker will attempt to register a second extension with the SIP server. Any calls made to this extension will play a ringtone.
Installing the VoIP V2 Speaker 34 Configure the Speaker Parameters 2.3.8 Configure the Multicast Parameters 1. Click on the Multicast Configuration button to open the Multicast Configuration page. See Figure 2-17. Figure 2-17.
Installing the VoIP V2 Speaker 35 Configure the Speaker Parameters 2. On the Multicast Configuration page, enter values for the parameters indicated in Table 2-10. Table 2-10. Multicast Configuration Parameters Web Page Item Description Enable Multicast Operation Enables or disables multicast operation. Device Settings Priority Indicates the priority for the multicast group. Priority 9 is the highest (emergency streams). 0 is the lowest (background music). See Section 2.3.8.
Installing the VoIP V2 Speaker 36 Configure the Speaker Parameters Lengthy Pages Concerning how lengthy pages are handled (where someone puts the phone down for 15 minutes), after the 2MB limit is reached, further data will be thrown away while the audio file is played back. When the file is done playing, it will stop throwing away input and begin buffering data for another four minutes.
Installing the VoIP V2 Speaker 37 Configure the Speaker Parameters 2.3.9 Configure the Audio Parameters Click the Audio Config button to open the Audio Configuration page. See Figure 2-18 and Figure 2-19. The Audio Configuration page is used to add custom audio to the board. User uploaded audio will take precedence over the audio files shipped with the Intercom. Figure 2-18.
Installing the VoIP V2 Speaker 38 Configure the Speaker Parameters Figure 2-19.
Installing the VoIP V2 Speaker 39 Configure the Speaker Parameters On the Audio Configuration page, enter values for the parameters indicated in Table 2-11. Note Each entry on the Audio Configuration page replaces one of the stock audio files on the board. When the input box displays the word default, the V2 Speaker is using the stock audio file. If that file is replaced with a user file, it will display the uploaded filename. Table 2-11.
Installing the VoIP V2 Speaker 40 Configure the Speaker Parameters Table 2-11. Audio Configuration Parameters (continued) Web Page Item Description The Save button will download a new user audio file to the board once you've selected the file by using the Browse button. The Save button will delete any preexisting user-uploaded audio files.
Installing the VoIP V2 Speaker 41 Configure the Speaker Parameters 2.3.9.1 User-created Audio Files User created audio files should be saved in the following format: RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz You can use the free utility Audacity to convert audio files into this format. See Figure 2-20 through Figure 2-22. Figure 2-20. Audacity 1 Figure 2-21.
Installing the VoIP V2 Speaker 42 Configure the Speaker Parameters When you export an audio file with Audacity, save the output as: ● WAV (Microsoft) signed 16 bit PCM. Figure 2-22.
Installing the VoIP V2 Speaker 43 Configure the Speaker Parameters 2.3.10 Configure the NTP Server and Clock Parameters Click the Clock Config button to open the NTP Server and Clock Configuration page. See Figure 2-23. Note The Clock Configuration page is always visible. If a clock is not installed, the Clock Status will indicate NOT INSTALLED. Otherwise it shows INSTALLED. Figure 2-23.
Installing the VoIP V2 Speaker 44 Configure the Speaker Parameters Table 2-12 shows the web page items on the NTP Server and Clock Configuration page. Table 2-12. NTP Server and Clock Configuration Web Page Item Description Clock Status Displays the current clock status. Clock Firmware Displays the current clock firmware version. NTP Settings NTP Server Allows you to select the NTP server (64 character limit). Posix Time Zone String See Section 2.3.10.1, "Time Zone Strings" (43 character limit).
Installing the VoIP V2 Speaker 45 Configure the Speaker Parameters 2.3.10.1 Time Zone Strings The posix time zone string tells the internal date and time utilities how to handle daylight savings time for different time zones. Table 2-13 shows some common strings. Table 2-13. Common Time Zone Strings Time Zone Time Zone String US Pacific time PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00 US Mountain time MST7MDT,M3.2.0/2:00:00,M11.1.0/2:00:00 US Eastern Time EST5EDT,M3.2.0/2:00:00,M11.1.
Installing the VoIP V2 Speaker 46 Configure the Speaker Parameters Time Zone String Examples Table 2-15 has some more examples of time zone strings. Table 2-15. Time Zone String Examples Time Zone Tokyo Time Zone String a IST-9 Berlinb CET-1MET,M3.5.0/1:00,M10.5.0/1:00 a.Tokyo does not use daylight savings time. b.For Berlin, daylight savings time starts on the last Sunday in March at 01:00 UTC, and ends on the last Sunday in October at 01:00 UTC, and is one hour ahead of UTC.
Installing the VoIP V2 Speaker 47 Configure the Speaker Parameters Table 2-16. World GMT Table (continued) Operations Guide Time Zone City or Area Zone Crosses GMT Greenwich Mean Time, Dublin GMT+1 Berlin, Rome GMT+2 Israel, Cairo GMT+3 Moscow, Kuwait GMT+4 Abu Dhabi, Muscat GMT+5 Islamabad, Karachi GMT+6 Almaty, Dhaka GMT+7 Bangkok, Jakarta GMT+8 Hong Kong, Beijing GMT+9 Tokyo, Osaka GMT+10 Sydney, Melbourne, Guam GMT+11 Magadan, Soloman Is.
Installing the VoIP V2 Speaker 48 Configure the Speaker Parameters 2.3.11 Configure the Event Parameters Click the Event Config button to open the Event Configuration page (Figure 2-25). The Event Configuration page specifies a remote server that can be used to receive HTTP POST events when actions take place on the board. Figure 2-25.
Installing the VoIP V2 Speaker 49 Configure the Speaker Parameters Table 2-17 shows the web page items on the Event Configuration page. Table 2-17. Event Configuration Web Page Item Description Enable Event Generation When selected, Event Generation is enabled. Remote Event Server Remote Event Server IP Type the Remote Event Server IP address. (64 character limit) Remote Event Server Port Type the Remote Event Server port number.
Installing the VoIP V2 Speaker 50 Configure the Speaker Parameters 2.3.11.1 Example Packets for Events The server and port are used to point to the listening server and the 'Remote Event Server URL' is the destination URL (typically the script running on the remote server that's used to parse and process the POST events). Note The XML is URL-encoded before transmission so the following examples are not completely accurate. Here are example packets for every event: POST xmlparse_engine HTTP/1.1 Host: 10.
Installing the VoIP V2 Speaker 51 Configure the Speaker Parameters Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 197 Content-Type: application/x-www-form-urlencoded RINGING POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 234 Content-Type: application/x-www-form-urlencoded
Installing the VoIP V2 Speaker 52 Configure the Speaker Parameters Content-Length: 234 Content-Type: application/x-www-form-urlencoded
Installing the VoIP V2 Speaker 53 Configure the Speaker Parameters 2.3.12 Configure the Autoprovisioning Parameters 1. Click the Autoprovisioning button to open the Autoprovisioning Configuration page. See Figure 2-26. Figure 2-26.
Installing the VoIP V2 Speaker 54 Configure the Speaker Parameters 2. On the Autoprovisioning Configuration page, you may enter values for the parameters indicated in Table 2-18. Table 2-18. Autoprovisioning Configuration Parameters Web Page Item Description Autoprovisioning Enable Autoprovisioning See Section 2.3.12.1, "Autoprovisioning". Get Autoprovisioning from DHCP See Section 2.3.12.1, "Autoprovisioning". Autoprovisioning Server (IP Address) See Section 2.3.12.
Installing the VoIP V2 Speaker 55 Configure the Speaker Parameters 2.3.12.1 Autoprovisioning Enable Autoprovisioning Option With autoprovisioning enabled, the board will get its configuration from a remote TFTP server on startup or periodically on a scheduled delay. Autoprovisioned values will override values stored in on-board memory and will be visible on the web page. The board gets its autoprovisioning information from an XML-formatted file hosted from a TFTP server.
Installing the VoIP V2 Speaker 56 Configure the Speaker Parameters To set up a Linux DHCPD server to serve autoprovisioning information (in this case using both option 66 and 150), here's an example dhcpd.conf: # dhcpd.conf # # Configuration file for ISC dhcpd (see 'man dhcpd.conf') # ddns-update-style ad-hoc; option option-150 code 150 = ip-address; subnet 10.0.0.0 netmask 255.0.0.0 { max-lease-time 120; default-lease-time 120; option routers option subnet-mask 10.0.0.1; 255.0.0.
Installing the VoIP V2 Speaker 57 Configure the Speaker Parameters Autoprovisioned Audio Files Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be downloaded once for each device. Loading many audio files to the device from the web page could cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh the page. The device uses the file name to determine when to download a new audio file.
Installing the VoIP V2 Speaker 58 Configure the Speaker Parameters 2.3.13 Upgrade the Firmware and Reboot the V2 Speaker 2.3.13.1 Upgrade the Firmware Caution GENERAL ALERT When upgrading to firmware version 6.x.x from version 5.x.x or earlier, your device configuration settings will be lost because the way that the device stores the configuration settings is different in version 6.x.x. To upload the firmware from your computer: 1.
Installing the VoIP V2 Speaker 59 Configure the Speaker Parameters 4. Click the Update Firmware button to open the Upgrade Firmware page. See Figure 2-27. Figure 2-27. Upgrade Firmware Page 5. Click Browse, and then navigate to the location of the V2 Speaker firmware file. 6. Click Submit. Operations Guide Note This starts the upload process. Once the V2 Speaker has uploaded the file, the Uploading Firmware countdown page appears, indicating that the firmware is being written to flash.
Installing the VoIP V2 Speaker 60 Configure the Speaker Parameters Table 2-19 shows the web page items on the Upgrade Firmware page. Table 2-19. Upgrade Firmware Parameters Description Web Page Item File Upload Firmware Version Firmware Version Please specify a file Refer to the Browse button description. Use the Browse button to navigate to the location of the Intercom firmware file that you want to upload. Click on the Submit button to automatically upload the selected firmware and reboot the system.
Installing the VoIP V2 Speaker 61 Configure the Speaker Parameters 2.3.13.2 Reboot the V2 Speaker To reboot a V2 Speaker, 1. Log in to the Home Page as instructed in Section 2.3.3, "Log in to the Configuration Home Page". See Figure 2-28. Figure 2-28. Home Page Reboot Reboot 2. Click the Reboot button. See Figure 2-28.
Installing the VoIP V2 Speaker 62 Configure the Speaker Parameters 3. A normal restart will occur and you will see the following Reboot page. Figure 2-29.
Installing the VoIP V2 Speaker 63 Command Interface 2.4 Command Interface Some functions on the device can be activated using simple POST commands to the web interface. The examples in Table 2-20 use the free unix utility, wget commands. However, any program that can send HTTP POST commands to the device should work. 2.4.1 Command Interface Post Commands Note These commands require an authenticated session (a valid username and password to work). Table 2-20.
Installing the VoIP V2 Speaker 64 Command Interface Table 2-20. Command Interface Post Commands (continued) Device Action HTTP Post Commanda Play the "6" audio file wget --user admin --password admin --auth-no-challenge --quiet -O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data "play_6=yes" Play the "7" audio file wget --user admin --password admin --auth-no-challenge --quiet -O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.
Installing the VoIP V2 Speaker 65 Command Interface Table 2-20. Command Interface Post Commands (continued) Device Action HTTP Post Commanda Delete the "3" audio file wget --user admin --password admin --auth-no-challenge --quiet -O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data "delete_3=yes" Delete the "4" audio file wget --user admin --password admin --auth-no-challenge --quiet -O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.
66 Appendix A: Mounting the Speaker A.1 Important Safety Instructions Warning Electrical Hazard: The VoIP V2 Speaker enclosure is not rated for any AC voltages. GENERAL ALERT Warning Electrical Hazard: This product should be installed by a licensed electrician according to all local electrical and building codes. GENERAL ALERT Warning Electrical Hazard: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
67 Mount the Speaker A.2 Mount the Speaker Before you mount the speaker, make sure that you have received all the parts for each speaker. Refer to Table A-1 and Table A-2. Table A-1. Drop Ceiling Mounting Components (Part of the Accessory Kit) Quantity Part Name 3 #8 Nylon Thumb Nuts 3 #8 Fender Washers 3 8-32 x 1 1/4" Mounting Screws Illustration Table A-2.
68 Mount the Speaker To mount the speaker: 1. Use the TEMPLATE to cut the speaker hole and prepare holes for the screws (Figure A-1). This template is located on the back page of the Installation Quick Reference Guide that is delivered with each speaker. Figure A-1.
69 Mount the Speaker 2. Plug the Ethernet cable into the Speaker Assembly. Section 2.2.3, "Confirm that the Speaker is Operational and Linked to the Network" explains how the Link and Status LEDs work. 3. At this point: • For drop ceiling mounting, position the VoIP SPEAKER ASSEMBLY in the ceiling so that its screw holes align with those you prepared.
70 Appendix B: Setting up a TFTP Server B.1 Set up a TFTP Server B.1.1 Autoprovisioning requires a TFTP server for hosting the configuration file. B.1.2 In a LINUX Environment To set up a TFTP server on LINUX: 1. Create a directory dedicated to the TFTP server, and move the files to be uploaded to that directory. 2. Run the following command where /tftpboot/ is the path to the directory you created in Step 1: the directory that contains the files to be uploaded. For example: in.
71 Appendix C: Troubleshooting/Technical Support C.1 Frequently Asked Questions (FAQ) To see a list of frequently asked questions for your product, go to the following URL: http://www.cyberdata.net/products/voip/digitalanalog/ceilingspkr2/faqs.html C.2 Documentation The documentation for this product is released in an English language version only. You can download PDF copies of CyberData product documentation by going to the following URL: http://www.cyberdata.
72 Contact Information C.3 Contact Information Contact CyberData Corporation 3 Justin Court Monterey, CA 93940 USA www.CyberData.net Phone: 800-CYBERDATA (800-292-3732) Fax: 831-373-4193 Sales Sales 831-373-2601 Extension 334 Technical Support The fastest way to get technical support for your VoIP product is to submit a VoIP Technical Support form at the following website: http://www.cyberdata.net/support/contactsupportvoip.
73 Warranty C.4 Warranty CyberData warrants its product against defects in material or workmanship for a period of two years from the date of purchase. Should the product fail Within Warranty, CyberData will repair or replace the product free of charge. This warranty includes all parts and labor. Should the product fail Out of the Warranty period, a flat rate repair charge of one half of the purchase price of the product will be assessed.
74 Warranty C.4.3 Spare in the Air Policy CyberData now offers a Spare in the Air no wait policy for warranty returns within the United States and Canada. More information about the Spare in the Air policy is available at the following web address: http://www.cyberdata.net/support/warranty/spareintheair.html C.4.4 Return and Restocking Policy For our authorized distributors and resellers, please refer to your CyberData Service Agreement for information on our return guidelines and procedures.
75 Index Symbols C #8 fender washers 67, 69 #8 nylon thumb nuts 67, 69 #8 sheet metal screws 67, 69 changing the web access password 25 clock configuration 43, 44 clock configuration page 43 clock status 43 command interface 63 commands 63 configurable parameters 24, 26, 28 configuration clock 43 default IP settings 20 device 8 NTP Server 43 SIP 29 using Web interface 20 configuration home page 23 configuration page configurable parameters 26 confirming IP address 17, 19 contact information 72 contact i
76 L downgrading (may restore factory defaults) 59 drop ceiling mounting of speaker 69 drywall mounting of speaker 69 lease, SIP server expiration time 30, 33 lengthy pages 35 link LED 69 Linux, setting up a TFTP server on 70 local SIP port 30 log in address 22 E enable night ring events 43, 49 Ethernet cable 69 ethernet port baud rate 5 event configuration enable night ring events 49 expiration time for SIP server lease 30, 33 M MGROUP MGROUP Name 35 mounting a speaker 67 multicast configuration 34 Mu
77 POST command 63 power input (J1) 5 power requirement 5 power, connecting to speaker 9 priority assigning 35 product configuring 20 mounting 67 parts list 7 product features 3 product overview 1 product features 3 product specifications 5 product specifications 5 Spare in the Air Policy 74 speaker configuration default IP settings 20 speaker configuration page configurable parameters 24, 28 speaker operations, verifying 25 static IP addressing 28 status LED 69 Stored Network Settings 28 subnet mask 8, 2
78 web configuration log in address 22 web page navigation 21 web page navigation 21 web-based speaker configuration 20 weight 5 wget, free unix utility 63 Windows, setting up a TFTP server on 70 Operations Guide 930274R CyberData Corporation
