The IP Endpoint Company Push-to-Talk V2 Speaker Operations Guide Part #011180, RAL 9002, Gray White, Standard Part #011181, RAL 9003, Signal White, Optional Document Part #930468A for Firmware Version 6.4.
Push-to-Talk V2 Speaker Operations Guide 930468A Part # 011180 Part # 011181 COPYRIGHT NOTICE: © 2012, CyberData Corporation, ALL RIGHTS RESERVED. This manual and related materials are the copyrighted property of CyberData Corporation. No part of this manual or related materials may be reproduced or transmitted, in any form or by any means (except for internal use by licensed customers), without prior express written permission of CyberData Corporation.
Revision Information Revision 930468A, which corresponds to firmware version 6.4.0, was released on November 13, 2012.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Pictorial Alert Icons GENERAL ALERT General Alert This pictoral alert indicates a potentially hazardous situation. This alert will be followed by a hazard level heading and more specific information about the hazard. Ground This pictoral alert indicates the Earth grounding connection point. Hazard Levels Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This is limited to the most extreme situations.
Abbreviations and Terms Abbreviation or Term Definition A-law A standard companding algorithm, used in European digital communications systems to optimize, i.e., modify, the dynamic range of an analog signal for digitizing. AVP Audio Video Profile Cat 5 TIA/EIA-568-B Category 5 DHCP Dynamic Host Configuration Protocol LAN Local Area Network LED Light Emitting Diode Mbps Megabits per Second. NTP Network Time Protocol PBX Private Branch Exchange PoE Power over Ethernet (as per IEEE 802.
i Contents Chapter 1 Product Overview 1 1.1 How to Identify This Product ..............................................................................................................1 1.2 Installation ...............................................................................................................................................2 1.3 Product Features .....................................................................................................................................2 1.
C.4.5 Warranty and RMA Returns Page .........................................................................................
1 1 Product Overview The CyberData SIP-enabled V2 Speaker is a Power-over-Ethernet (PoE 802.3af) and Voice-over-IP (VoIP) public address loudspeaker that easily connects into existing local area networks with a single CAT5 cable connection. The speaker is compatible with most SIP-based IP PBX. In a non-SIP environment, the speaker is capable of receiving broadcast audio via multicast. Its small footprint and low height allows the speaker to be discretely mounted almost anywhere.
Product Overview 2 Installation 1.2 Installation Figure 1-2 illustrates a typical configurations for the VoIP V2 Speaker. Figure 1-2. Typical Installation 802.3af Compliant Ethernet Switch 1 Remote Call Button IP Talkback Speaker 2 3 4 5 6 IP Speaker IP Phone IP PBX Server See the following sections for other installation options: • Section 2.2.1.3, "Running the Talkback Speaker with Auxiliary Power" • Section 2.2.2.2, "Talkback Speaker with an External Device" • Section 2.2.2.
Product Overview 3 Supported Protocols 1.4 Supported Protocols The V2 Speaker supports: • SIP • Multicast • HTTP Web-based configuration Provides an intuitive user interface for easy system configuration and verification of speaker operations. • DHCP Client Dynamically assigns IP addresses in addition to the option to use static addressing. • HTTP TCP Post auto-updating event notification in XML format • TFTP Client Facilitates hosting for the configuration file for Autoprovisioning.
Product Overview 4 Product Specifications 1.6 Product Specifications Table 1-1. Product Specifications Category Specification Audio sensitivity 96dB/1W/1M S.P. Level Audio output 10 Watts Peak Power Operating temperature -30 to 55 C (-22 to 131 F) Ethernet port baud rate 10/100 Mbps Protocol SIP RFC 3261 Compatible Power Input (J1) PoE 802.3af (as per IEEE 802.
Product Overview 5 Optional Connections (J9 and J10) 1.7 Optional Connections (J9 and J10) Figure 1-3. Optional Connections (J9 and J10) Function J10 Connections *Auxiliary power input for use when PoE power is not available. 12 VDC @ 1A. AUX POWER (+) (+12VDC @ 1A) AUX SPEAKER (-) AUX POWER (-) AUX SPEAKER (+) Relay contacts rated at 30 VDC @ 1A. J9 Connections RELAY COM Function Auxiliary 8-Ohm speaker connection (not to be used when the Clock is connected.
Product Overview 6 Push-To-Talk Speaker Modes 1.9 Push-To-Talk Speaker Modes 1.9.1 Normal Mode • In Normal Mode, a person can use the Remote Call Button and the Talkback Speaker to call an IP phone or a phone user can call the talkback speaker. See Figure 1-5. Figure 1-5. Normal Mode Talkback Speaker makes a call or dials a SIP extension. Talkback Speaker OR Phone user dials the Talkback Speaker. IP Phone Push the Call Button • Push the Call Button to make a call or dial the SIP extension.
Product Overview 7 Push-To-Talk Speaker Modes • To talk to someone on the other end, the person at the V2 Speaker, must hold down the Call Button while they are talking to the person on the other end. See Figure 1-7. Figure 1-7. Hold Down the Call Button While Talking Hold down the Call Button while talking • To listen to someone talking on the other end, the person at the V2 Speaker must release the Call Button. See Figure 1-8. Figure 1-8.
Product Overview 8 Push-To-Talk Speaker Modes 1.9.2 Monitor Mode • In Monitor Mode, the person on the phone can listen to any activity that is occurring near the Push-to-Talk Speaker. See Figure 1-9. Figure 1-9. Monitor Mode Talkback Speaker IP Phone Sound, noise, or activity near the V2 Speaker • The Call Button is not used during Monitor Mode. • Monitor Mode is controlled by the phone instead of the Push-to-Talk Speaker.
Product Overview 9 Push-To-Talk Speaker Modes • In Monitor Mode, the "talking mode" and the "listening mode" are controlled by one of the preprogrammed buttons on the phone keypad. Therefore, if someone is in the "listening mode," they must press a pre-programmed keypad button to enter the "talking mode." Conversely, if someone is in the "talking mode," they must press a pre-programmed keypad button to enter the "listening mode." Figure 1-11.
10 2 Installing the VoIP V2 Speaker 2.1 Parts List Table 2-1 illustrates the parts for each speaker and includes kits for the drop ceiling and drywall mounting. The installation template for the Talkback Speaker is located on the Installation Quick Reference Guide that is included in the packaging with each speaker. Note Table 2-1.
Installing the VoIP V2 Speaker 11 2.2 Device Configuration Set up and configure each speaker before you mount it. CyberData delivers each speaker with the following factory default values: Table 2-2. Factory Network Default Settings—Default of Network Parameter Factory Default Setting IP Addressing DHCP IP Address a 10.10.10.10 Web Access Username admin Web Access Password admin Subnet Maska 255.0.0.0 Default Gatewaya 10.0.0.1 a. Default if there is not a DHCP server present.
Installing the VoIP V2 Speaker 12 Connect Power to the Speaker 2.2.1 Connect Power to the Speaker Figure 2-1 through Figure 2-3 illustrates how to connect power to the VoIP V2 Speaker. 2.2.1.1 Push-to-Talk V2 Speaker to a 802.3af Compliant PoE Switch Figure 2-1 illustrates how to connect the VoIP V2 Speaker to a 802.3af compliant PoE switch via a Cat 5 Ethernet cable. Figure 2-1. Push-to-Talk V2 Speaker to a 802.3af Compliant PoE Switch Cat 5 Ethernet cable 802.
Installing the VoIP V2 Speaker 13 Connect Power to the Speaker 2.2.1.2 Push-to-Talk V2 Speaker (with PoE Injector) to a 802.3af Compliant PoE Switch In Figure 2-2, if a PoE switch is not available, you will need a PoE Injector, part #010867A (ordered separately). A PoE Injector is a power supply solution for those who have a standard Non PoE Switch. Figure 2-2.
Installing the VoIP V2 Speaker 14 Connect Power to the Speaker 2.2.1.3 Running the Talkback Speaker with Auxiliary Power In Figure 2-3, the power for the Talkback Speaker can either come from an 802.3af Network connection or from an external source. Caution GENERAL ALERT Operational Note: Do not connect an auxiliary power supply when the Talkback Speaker is connected to a PoE power source through J1. Improper operation or equipment damage may occur. Figure 2-3.
Installing the VoIP V2 Speaker 15 Installation Options 2.2.2 Installation Options This section shows various installation options for the Talkback Speaker. 2.2.2.1 Running the Talkback Speaker with a Remote Call Button In Figure 2-3, the VoIP Remote Call Button enables calls to the SIP Talkback Speaker that can be initiated or answered from a remotely-mounted switch.
Installing the VoIP V2 Speaker 16 Installation Options 2.2.2.2 Talkback Speaker with an External Device In Figure 2-5, when the Talkback Speaker is called from a remote phone, the relay on the speaker can be programmed to drive an external device such as an alert strobe. This external device may also be addressed from a separate Unified Communication (UC) server. Figure 2-5.
Installing the VoIP V2 Speaker 17 Installation Options 2.2.2.3 Talkback Speaker with Auxiliary Speaker Connection In Figure 2-6, the Talkback Speaker supports an amplified audio output for a second analog speaker. While the total speaker wattage is the same, by connecting a low cost analog speaker, additional coverage can be realized.
Installing the VoIP V2 Speaker 18 Installation Options Figure 2-7. Clock Kit with Extra Speaker Connection is NOT ALLOWED.
Installing the VoIP V2 Speaker 19 Installation Options 2.2.2.4 Talkback Speaker with Line Out In Figure 2-8, for areas that require more speaker volume, the Talkback Speaker can be connected directly to an auxiliary amplifier to drive additional horns or speakers. This is done through the lineout connection. Figure 2-8. Talkback Speaker with Line Out Speaker Office area in Factory AUX POWER (+) (+12VDC @ 1A) Line Out: Output Signal Amplitudes 2.
Installing the VoIP V2 Speaker 20 Confirm that the Speaker is Operational and Linked to the Network 2.2.3 Confirm that the Speaker is Operational and Linked to the Network After connecting the speaker to the 802.3af compliant Ethernet hub, the LEDs on the speaker face confirm that the speaker is operational and linked to the network. Figure 2-9. Status and Activity LEDs Network Link/Activity (Yellow) Speaker Status (Green) 2.2.3.1 Status LED After supplying power to the speaker: 1.
Installing the VoIP V2 Speaker 21 Confirm the IP Address and Test the Audio 2.2.4 Confirm the IP Address and Test the Audio 2.2.4.1 Reset Test Function Management (RTFM) Button When the speaker is operational and linked to the network, use the Reset Test Function Management (RTFM) button (Figure 2-10) on the speaker face to announce and confirm the speaker’s IP Address and test that the audio is working.
Installing the VoIP V2 Speaker 22 Adjust the Volume 2.2.5 Adjust the Volume To adjust the speaker volume, turn the Volume control dial (Figure 2-11) on the speaker face. Note The Talkback Speaker has two volume controls: Internal (web-based) and External (volume knob). The external volume control can be disabled from the web interface by selecting Use Digital Volume Control on the Device Configuration Page (see Section 2.3.3, "Configure the Device Parameters"). Figure 2-11.
Installing the VoIP V2 Speaker 23 How to Set the Factory Default Settings 2.2.6 How to Set the Factory Default Settings 2.2.6.1 RTFM Button When the speaker is operational and linked to the network, use the Reset Test Function Management (RTFM) button (Figure 2-12) on the speaker face to set the factory default settings. Figure 2-12. RTFM Button RTFM button To set the factory default settings: 1. Press and hold the RTFM button for more than five seconds. 2.
Installing the VoIP V2 Speaker 24 How to Set the Factory Default Settings 2.3 Configure the Speaker Parameters To configure the speaker online, use a standard web browser. Configure each speaker and verify its operation before you mount it. When you are ready to mount a speaker, refer to Appendix A, "Mounting the Speaker" for instructions.
Installing the VoIP V2 Speaker 25 Talkback Speaker Web Page Navigation 2.3.1 Talkback Speaker Web Page Navigation Table 2-4 shows the navigation buttons that you will see on every Talkback Speaker web page. Table 2-4. V2 Paging Amplifier Web Page Navigation Web Page Item Description Link to the Home page. Link to the Device Configuration page. Link to the Networking page. Link to go to the SIP Configuration page. Link to go to the Nightringer page. Link to the Multicast Configuration page.
Installing the VoIP V2 Speaker 26 Log in to the Configuration Home Page 2.3.2 Log in to the Configuration Home Page 1. Open your browser to the Talkback Speaker IP address. Note If the network does not have access to a DHCP server, the device will default to an IP address of 10.10.10.10. Note Make sure that the PC is on the same IP network as the Talkback Speaker.
Installing the VoIP V2 Speaker 27 Log in to the Configuration Home Page 2. When prompted, use the following default Web Access Username and Web Access Password to access the Home Page (Figure 2-13): Web Access Username: admin Web Access Password: admin Figure 2-13.
Installing the VoIP V2 Speaker 28 Log in to the Configuration Home Page 3. On the Home Page, review the setup details and navigation buttons described in Table 2-5. Table 2-5. Home Page Overview Web Page Item Description Device Settings Device Name Shows the device name (25 character limit). Change Username Type in this field to change the username (25 character limit). Change Password Type in this field to change the password (19 character limit).
Installing the VoIP V2 Speaker 29 Configure the Device Parameters 2.3.3 Configure the Device Parameters 1. Click the Device Configuration button to open the Device Configuration page. See Figure 2-14. Figure 2-14.
Installing the VoIP V2 Speaker 30 Configure the Device Parameters 2. On the Device Configuration page, you may enter values for the parameters indicated in Table 2-6. Table 2-6. Device Configuration Parameters Web Page Item Description Volume Settings Use Digital Volume Control When selected, you can bypass the analog volume knob on the front of the speaker. The volume level will only be determined by the digital Speaker Volume setting on the Device Configuration page.
Installing the VoIP V2 Speaker 31 Configure the Device Parameters Table 2-6. Device Configuration Parameters (continued) Web Page Item Description Click on the Test Audio button to do an audio test. When the Test Audio button is pressed, you will hear a voice message for testing the device audio quality and volume. Click on the Test Microphone button to do a microphone test. When the Test Microphone button is pressed, the following occurs: 1. The device will immediately start recording 3 seconds of audio.
Installing the VoIP V2 Speaker 32 Configure the Network Parameters 2.3.4 Configure the Network Parameters 1. Click the Networking button to open the Network Configuration page (Figure 2-15). Figure 2-15.
Installing the VoIP V2 Speaker 33 Configure the Network Parameters 2. On the Network Configuration page, enter values for the parameters indicated in Table 2-7. Table 2-7. Network Configuration Parameters Web Page Item Description Stored Network Settings Shows the settings stored in non-volatile memory. IP Addressing Select either DHCP IP Addressing or Static IP Addressing by marking the appropriate radio button. If you select Static, configure the remaining parameters indicated in Table 2-7.
Installing the VoIP V2 Speaker 34 Configure the SIP Parameters 2.3.5 Configure the SIP Parameters 1. Click SIP Config to open the SIP Configuration page (Figure 2-17). Note For specific server configurations, go to the following website address: http://www.cyberdata.net/support/server/index.html Figure 2-16.
Installing the VoIP V2 Speaker 35 Configure the SIP Parameters Figure 2-17.
Installing the VoIP V2 Speaker 36 Configure the SIP Parameters 2. On the SIP Configuration page, you may enter values for the parameters indicated in Table 2-8. Table 2-8. SIP Configuration Parameters Web Page Item Description Primary SIP Server Shows the current status of the Primary SIP Server. Backup Server 1 Shows the current status of Backup Server 1. Backup Server 2 Shows the current status of Backup Server 2. Monitor SIP Server Shows the current status of the Monitor SIP Server.
Installing the VoIP V2 Speaker 37 Configure the SIP Parameters Table 2-8. SIP Configuration Parameters (continued) Web Page Item Description Backup Monitor User ID 1 Type the Monitor User ID for the Backup SIP Server (up to 64 alphanumeric characters). Backup Monitor User ID 2 Backup Monitor Auth ID 1 Type the Monitor Authenticate ID for the Backup SIP Server (up to 64 alphanumeric characters).
Installing the VoIP V2 Speaker 38 Configure the SIP Parameters Table 2-8. SIP Configuration Parameters (continued) Web Page Item Description Click the Save button to save your configuration settings. Note: You need to reboot for changes to take effect. Click on the Reboot button to reboot the system. 3. After changing the parameters, click on the Save button. 2.3.5.
Installing the VoIP V2 Speaker 39 Configure the Night Ringer Parameters 2.3.6 Configure the Night Ringer Parameters 1. Click on the Nightringer button to open the Nightringer Configuration page. See Figure 2-18. Figure 2-18.
Installing the VoIP V2 Speaker 40 Configure the Night Ringer Parameters 2. On the Nightringer Configuration page, enter values for the parameters indicated in Table 2-10. Table 2-10. Nightringer Configuration Parameters Web Page Item Description Enable Nightringer When the nightringer is enabled, the ceiling speaker will attempt to register a second extension with the SIP server. Any calls made to this extension will play a ringtone.
Installing the VoIP V2 Speaker 41 Configure the Multicast Parameters 2.3.7 Configure the Multicast Parameters 1. Click on the Multicast Configuration button to open the Multicast Configuration page. See Figure 2-19. Figure 2-19.
Installing the VoIP V2 Speaker 42 Configure the Multicast Parameters 2. On the Multicast Configuration page, enter values for the parameters indicated in Table 2-11. Table 2-11. Multicast Configuration Parameters Web Page Item Description Enable Multicast Operation Enables or disables multicast operation. Device Settings Priority Indicates the priority for the multicast group. Priority 9 is the highest (emergency streams). 0 is the lowest (background music). See Section 2.3.7.
Installing the VoIP V2 Speaker 43 Configure the Multicast Parameters Lengthy Pages Concerning how lengthy pages are handled (where someone puts the phone down for 15 minutes), after the 2MB limit is reached, further data will be thrown away while the audio file is played back. When the file is done playing, it will stop throwing away input and begin buffering data for another four minutes.
Installing the VoIP V2 Speaker 44 Configure the Audio Parameters 2.3.8 Configure the Audio Parameters Click the Audio Config button to open the Audio Configuration page. See Figure 2-20 and Figure 2-21. The Audio Configuration page is used to add custom audio to the board. User uploaded audio will take precedence over the audio files shipped with the Intercom. Figure 2-20.
Installing the VoIP V2 Speaker 45 Configure the Audio Parameters Figure 2-21.
Installing the VoIP V2 Speaker 46 Configure the Audio Parameters On the Audio Configuration page, enter values for the parameters indicated in Table 2-12. Note Each entry on the Audio Configuration page replaces one of the stock audio files on the board. When the input box displays the word default, the Talkback Speaker is using the stock audio file. If that file is replaced with a user file, it will display the uploaded filename. Table 2-12.
Installing the VoIP V2 Speaker 47 Configure the Audio Parameters Table 2-12. Audio Configuration Parameters (continued) Web Page Item Description The Delete button will delete any user uploaded audio and restore the stock audio file. The Save button will download a new user audio file to the board once you've selected the file by using the Browse button. The Save button will delete any preexisting user-uploaded audio files.
Installing the VoIP V2 Speaker 48 Configure the Audio Parameters 2.3.8.1 User-created Audio Files User created audio files should be saved in the following format: RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz You can use the free utility Audacity to convert audio files into this format. See Figure 2-22 through Figure 2-24. Figure 2-22. Audacity 1 Figure 2-23.
Installing the VoIP V2 Speaker 49 Configure the Audio Parameters When you export an audio file with Audacity, save the output as: ● WAV (Microsoft) signed 16 bit PCM. Figure 2-24.
Installing the VoIP V2 Speaker 50 Configure the NTP Server and Clock Parameters 2.3.9 Configure the NTP Server and Clock Parameters Click the Clock Config button to open the NTP Server and Clock Configuration page. See Figure 2-25. Note The Clock Configuration page is always visible. If a clock is not installed, the Clock Status will indicate NOT INSTALLED. Otherwise it shows INSTALLED. Figure 2-25.
Installing the VoIP V2 Speaker 51 Configure the NTP Server and Clock Parameters Table 2-13 shows the web page items on the NTP Server and Clock Configuration page. Table 2-13. NTP Server and Clock Configuration Web Page Item Description Clock Status Displays the current clock status. Clock Firmware Displays the current clock firmware version. NTP Settings NTP Server Allows you to select the NTP server (64 character limit). Posix Time Zone String See Section 2.3.9.
Installing the VoIP V2 Speaker 52 Configure the NTP Server and Clock Parameters 2.3.9.1 Time Zone Strings The posix time zone string tells the internal date and time utilities how to handle daylight savings time for different time zones. Table 2-14 shows some common strings. Table 2-14. Common Time Zone Strings Time Zone Time Zone String US Pacific time PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00 US Mountain time MST7MDT,M3.2.0/2:00:00,M11.1.0/2:00:00 US Eastern Time EST5EDT,M3.2.0/2:00:00,M11.1.
Installing the VoIP V2 Speaker 53 Configure the NTP Server and Clock Parameters Time Zone String Examples Table 2-16 has some more examples of time zone strings. Table 2-16. Time Zone String Examples Time Zone Time Zone String Tokyoa IST-9 Berlin b CET-1MET,M3.5.0/1:00,M10.5.0/1:00 a.Tokyo does not use daylight savings time. b.For Berlin, daylight savings time starts on the last Sunday in March at 01:00 UTC, and ends on the last Sunday in October at 01:00 UTC, and is one hour ahead of UTC.
Installing the VoIP V2 Speaker 54 Configure the NTP Server and Clock Parameters Table 2-17. World GMT Table (continued) Operations Guide Time Zone City or Area Zone Crosses GMT Greenwich Mean Time, Dublin GMT+1 Berlin, Rome GMT+2 Israel, Cairo GMT+3 Moscow, Kuwait GMT+4 Abu Dhabi, Muscat GMT+5 Islamabad, Karachi GMT+6 Almaty, Dhaka GMT+7 Bangkok, Jakarta GMT+8 Hong Kong, Beijing GMT+9 Tokyo, Osaka GMT+10 Sydney, Melbourne, Guam GMT+11 Magadan, Soloman Is.
Installing the VoIP V2 Speaker 55 Configure the Event Parameters 2.3.10 Configure the Event Parameters Click the Event Config button to open the Event Configuration page (Figure 2-27). The Event Configuration page specifies a remote server that can be used to receive HTTP POST events when actions take place on the board. Figure 2-27.
Installing the VoIP V2 Speaker 56 Configure the Event Parameters Table 2-18 shows the web page items on the Event Configuration page. Table 2-18. Event Configuration Web Page Item Description Enable Event Generation When selected, Event Generation is enabled. Remote Event Server Remote Event Server IP Type the Remote Event Server IP address. (64 character limit) Remote Event Server Port Type the Remote Event Server port number.
Installing the VoIP V2 Speaker 57 Configure the Event Parameters 2.3.10.1 Example Packets for Events The server and port are used to point to the listening server and the 'Remote Event Server URL' is the destination URL (typically the script running on the remote server that's used to parse and process the POST events). Note The XML is URL-encoded before transmission so the following examples are not completely accurate. Here are example packets for every event: POST xmlparse_engine HTTP/1.1 Host: 10.0.
Installing the VoIP V2 Speaker 58 Configure the Event Parameters Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 197 Content-Type: application/x-www-form-urlencoded RINGING POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 234 Content-Type: application/x-www-form-urlencoded
Installing the VoIP V2 Speaker 59 Configure the Event Parameters Content-Length: 234 Content-Type: application/x-www-form-urlencoded
Installing the VoIP V2 Speaker 60 Configure the Autoprovisioning Parameters 2.3.11 Configure the Autoprovisioning Parameters 1. Click the Autoprovisioning button to open the Autoprovisioning Configuration page. See Figure 2-28. Figure 2-28.
Installing the VoIP V2 Speaker 61 Configure the Autoprovisioning Parameters 2. On the Autoprovisioning Configuration page, you may enter values for the parameters indicated in Table 2-19. Table 2-19. Autoprovisioning Configuration Parameters Web Page Item Description Autoprovisioning Enable Autoprovisioning See Section 2.3.11.1, "Autoprovisioning". Get Autoprovisioning from DHCP See Section 2.3.11.1, "Autoprovisioning". Autoprovisioning Server (IP Address) See Section 2.3.11.
Installing the VoIP V2 Speaker 62 Configure the Autoprovisioning Parameters 2.3.11.1 Autoprovisioning Enable Autoprovisioning Option With autoprovisioning enabled, the board will get its configuration from a remote TFTP server on startup or periodically on a scheduled delay. Autoprovisioned values will override values stored in on-board memory and will be visible on the web page. The board gets its autoprovisioning information from an XML-formatted file hosted from a TFTP server.
Installing the VoIP V2 Speaker 63 Configure the Autoprovisioning Parameters To set up a Linux DHCPD server to serve autoprovisioning information (in this case using both option 66 and 150), here's an example dhcpd.conf: # dhcpd.conf # # Configuration file for ISC dhcpd (see 'man dhcpd.conf') # ddns-update-style ad-hoc; option option-150 code 150 = ip-address; subnet 10.0.0.0 netmask 255.0.0.0 { max-lease-time 120; default-lease-time 120; option routers option subnet-mask 10.0.0.1; 255.0.0.
Installing the VoIP V2 Speaker 64 Configure the Autoprovisioning Parameters Autoprovisioned Audio Files Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be downloaded once for each device. Loading many audio files to the device from the web page could cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh the page. The device uses the file name to determine when to download a new audio file.
Installing the VoIP V2 Speaker 65 Upgrade the Firmware and Reboot the Talkback Speaker 2.3.12 Upgrade the Firmware and Reboot the Talkback Speaker 2.3.12.1 Upgrade the Firmware Caution GENERAL ALERT When upgrading to firmware version 6.x.x from version 5.x.x or earlier, your device configuration settings will be lost because the way that the device stores the configuration settings is different in version 6.x.x. To upload the firmware from your computer: 1.
Installing the VoIP V2 Speaker 66 Upgrade the Firmware and Reboot the Talkback Speaker 4. Click the Update Firmware button to open the Upgrade Firmware page. See Figure 2-29. Figure 2-29. Upgrade Firmware Page 5. Click Browse, and then navigate to the location of the Talkback Speaker firmware file. 6. Click Submit. Operations Guide Note This starts the upload process.
Installing the VoIP V2 Speaker 67 Upgrade the Firmware and Reboot the Talkback Speaker Table 2-20 shows the web page items on the Upgrade Firmware page. Table 2-20. Upgrade Firmware Parameters Web Page Item Description File Upload Firmware Version Firmware Version Please specify a file Refer to the Browse button description. Use the Browse button to navigate to the location of the Intercom firmware file that you want to upload.
Installing the VoIP V2 Speaker 68 Upgrade the Firmware and Reboot the Talkback Speaker 2.3.12.2 Reboot the Talkback Speaker To reboot a Talkback Speaker, 1. Log in to the Home Page as instructed in Section 2.3.2, "Log in to the Configuration Home Page". See Figure 2-30. Figure 2-30. Home Page Reboot 2. Click the Reboot button. See Figure 2-30.
Installing the VoIP V2 Speaker 69 Upgrade the Firmware and Reboot the Talkback Speaker 3. A normal restart will occur and you will see the following Reboot page. Figure 2-31.
Installing the VoIP V2 Speaker 70 Command Interface Post Commands 2.4 Command Interface Some functions on the device can be activated using simple POST commands to the web interface. The examples in Table 2-21 use the free unix utility, wget, but any program that can send http POST commands to the device should work. 2.4.1 Command Interface Post Commands Note These commands require an authenticated session (a valid username and password to work). Table 2-21.
Installing the VoIP V2 Speaker 71 Command Interface Post Commands Table 2-21. Command Interface Post Commands (continued) HTTP Post Command a Device Action Play the "5" audio file wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data "play_5=yes" Play the "6" audio file wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.
Installing the VoIP V2 Speaker 72 Command Interface Post Commands Table 2-21. Command Interface Post Commands (continued) HTTP Post Command a Device Action Play the "5" audio file wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data "play_5=yes" Play the "6" audio file wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.
Installing the VoIP V2 Speaker 73 Command Interface Post Commands Table 2-21. Command Interface Post Commands (continued) HTTP Post Command a Device Action Delete the "0" audio file wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data "delete_0=yes" Delete the "1" audio file wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.
Installing the VoIP V2 Speaker 74 Command Interface Post Commands Table 2-21. Command Interface Post Commands (continued) HTTP Post Command a Device Action Delete the "Ring tone" audio file wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data "delete_ringtone=yes" Delete the "Intrusion Sensor Triggered" audio file wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.
75 Appendix A: Mounting the Speaker A.1 Mount the Speaker Before you mount the speaker, make sure that you have received all the parts for each speaker. Refer to Table A-1 and Table A-2. Table A-1. Drop Ceiling Mounting Components (Part of the Accessory Kit) Quantity Part Name 3 #8 Nylon Thumb Nuts 3 #8 Fender Washers 3 8-32 x 1 1/4" Mounting Screws Illustration Table A-2.
76 Mount the Speaker To mount the speaker: 1. Use the TEMPLATE to cut the speaker hole and prepare holes for the screws (Figure A-1). This template is located on the back page of the Installation Quick Reference Guide that is delivered with each speaker. Figure A-1.
77 Mount the Speaker 2. Plug the Ethernet cable into the Speaker Assembly. Section 2.2.3, "Confirm that the Speaker is Operational and Linked to the Network" explains how the Link and Status LEDs work. 3. At this point: • For drop ceiling mounting, position the VoIP SPEAKER ASSEMBLY in the ceiling so that its screw holes align with those you prepared.
78 Appendix B: Setting up a TFTP Server B.1 Set up a TFTP Server Autoprovisioning requires a TFTP server for hosting the configuration file. B.1.1 In a LINUX Environment To set up a TFTP server on LINUX: 1. Create a directory dedicated to the TFTP server, and move the files to be uploaded to that directory. 2. Run the following command where /tftpboot/ is the path to the directory you created in Step 1: the directory that contains the files to be uploaded. For example: in.
79 Appendix C: Troubleshooting/Technical Support C.1 Frequently Asked Questions (FAQ) To see a list of frequently asked questions for your product, go to the following URL: http://www.cyberdata.net/products/voip/digitalanalog/ceilingspkr2ptt/faqs.html C.2 Documentation The documentation for this product is released in an English language version only. You can download PDF copies of CyberData product documentation by going to the following URL: http://www.cyberdata.
80 Contact Information C.3 Contact Information Contact CyberData Corporation 3 Justin Court Monterey, CA 93940 USA www.CyberData.net Phone: 800-CYBERDATA (800-292-3732) Fax: 831-373-4193 Sales Sales 831-373-2601 Extension 334 Technical Support The fastest way to get technical support for your VoIP product is to submit a VoIP Technical Support form at the following website: http://www.cyberdata.net/support/contactsupportvoip.
81 Warranty C.4 Warranty CyberData warrants its product against defects in material or workmanship for a period of two years from the date of purchase. Should the product fail within the warranty period, CyberData will repair or replace the product free of charge. This warranty includes all parts and labor. Should the product fail out-of-warranty, a flat rate repair charge of one half of the purchase price of the product will be assessed.
82 Warranty C.4.4 Return and Restocking Policy For our authorized distributors and resellers, please refer to your CyberData Service Agreement for information on our return guidelines and procedures. For End Users, please contact the company that you purchased your equipment from for their return policy. C.4.5 Warranty and RMA Returns Page The most recent warranty and RMA information is available at the CyberData Warranty and RMA Returns Page at the following web address: http://www.cyberdata.
83 Index Symbols C #8 fender washers 75, 77 #8 nylon thumb nuts 75, 77 #8 sheet metal screws 75, 77 changing the web access password 29 clock configuration 50, 51 clock configuration page 50 clock status 50 command interface 70 commands 70 configurable parameters 28, 30, 33 configuration clock 50 default IP settings 24 device 11 NTP Server 50 SIP 34 using Web interface 24 configuration home page 27 configuration page configurable parameters 30 confirming IP address 21, 23 contact information 80 contact
84 L door sensor 46 downgrading (may restore factory defaults) 66 drop ceiling mounting of speaker 77 drywall mounting of speaker 77 DTMF tones 38 DTMF tones (using rfc2833) 38 lease, SIP server expiration time 37, 40 lengthy pages 42 link LED 77 Linux, setting up a TFTP server on 78 local SIP port 37 log in address 26 E M enable night ring events 50, 56 Ethernet cable 77 ethernet port baud rate 4 event configuration enable night ring events 56 expiration time for SIP server lease 37, 40 MGROUP MGROUP
85 #8 sheet metal screws 75 8-32 x 1 1/4" mounting screws 75 plastic ribbed anchors 75 password for monitor SIP server login 36 for SIP server login 36 login 27 restoring the default 11, 24 plastic ribbed anchors 75, 77 port local SIP 37 remote SIP 37 POST command 70 power input (J1) 4 power requirement 4 power, connecting to speaker 12 priority assigning 42 product configuring 24 mounting 75 parts list 10 product features 2 product overview 1 product features 2 product specifications 4 product specificati
86 volume, adjusting 23 W warranty 81 warranty & RMA returns outside of the United States 81 warranty & RMA returns within the United States 81 warranty and RMA returns page 82 warranty policy at CyberData 81 web access password 11, 24 web access username 11, 24 web configuration log in address 26 web page navigation 25 web page navigation 25 web-based speaker configuration 24 weight 4 wget, free unix utility 70 Windows, setting up a TFTP server on 78 Operations Guide 930468A CyberData Corporation
