Cyber Controller INSTRUCTION MANUAL Please read this manual thoroughly before use and keep it handy for future reference.
WARNINGS and CAUTIONS WARNINGS x TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. - DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. - DO NOT INSERT ANY MEALMETALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHERS OPENINGS ON THE EQUIPMENT.
COMPLIANCE STATEMENT FCC INFORMATION : THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT.
IMPORTANT SAFEGUARDS Please install the product on a completely flat floor. - Always check the strength and stability of the installation location. - Do not drop the appliance on the floor. This may result in damage or injury. Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers. - There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.
TABLE of CONTENTS WARNINGS AND CAUTIONS 2 COMPLIANCE STATEMENT 3 CE COMPLIANCE STATEMENT IMPORTANT SAFEGUARDS 4 1. INTRODUCTION 6 2. PACKAGE CONTENTS 7 3. INSTALLATION CONFIGURATION 8 3.1 Basic Configuration of DVR & Cyber Controller 8 3.2 Basic Configuration of Matrix System & Cyber Controller 9 3.3 The Example of Multi Configuration 10 4. OPERATING CONTROLS 11 4.1 Front View 11 4.2 Rear View 12 4.3 Operation by Part 13 5. OPERATION 16 5.1 POWER 16 5.
1. INTRODUCTION The Cyber Controller, Cyber Scan Dome, Video Matrix System & Digital Video Recorder make up the building blocks for any surveillance/security system. Using a multiple Cyber Controller and multiple dome cameras, no place is too large for monitoring and recording. Extendable and flexible architecture facilitates remote control functions for a variety of external switching devices such as DVR, Matrix System and Cyber Scan Dome Camera.
1.
3. INSTALLATION & CONFIGURATION 3.
3. INSTALLATION & CONFIGURATION 3.
3. INSTALLATION & CONFIGURATION 3.
4. OPERATING CONTROLS 4.
4. OPERATING CONTROLS 4.2 Rear View ① RS-232 : This connector port is provided to connect the external modem for remote monitoring, configuration and software upgrades. Use a modem cable with ADB-9S(female) connector to connect to the Cyber controller. Notice : A Modem cable not supplied so make certain you have the correct cable when you connect to the Cyber controller. ② ID DIP Switch : It is used to select Cyber controller ID. ③ RJ-45 JACK (IN/OUT) IN : Data Input port from the slave controller.
4. OPERATING CONTROLS 4.3 Operation by Part LEDs Part CAM : The Camera status indication. DVR : The DVR status Indication. MON : The Monitor(Matrix switcher) status Indication. TX/RX : Communication status indication. POWER : Turned on while the power is supplied. SHIFT : Turned on when SHIFT button is pressed. ALARM : Turned on when an alarm is activated. DVR Function Part MULTI : It is used to select the Quad screen. Whenever this button is pressed, the live screen status varies.
4. OPERATING CONTROLS DVR Search Part SEARCH : It is used to search the stored video data. ▶/ ll : It is used to activate the searched video data or bring them to a temporary stop. ◀◀REW : It allows data to be wounded in the reverse direction during retrieval. FF▶▶ : It allows searched data to be played out at higher speeds than the normal speed. Jog : It is used to search by 1 Frame.
4. OPERATING CONTROLS PTZ Camera Function Part PRESET : It is used to set the Preset function. TOUR : It is used to set the Tour function. PTRN : It is used to set the Pattern function. SCAN : It is used to set the Auto Scan function. MENU : It is used to select the Set up Menu. It is also used to execute or close Menu. HOME : It is used to set the Home function. QMAP : Quick Mapping function. It is used to call a User Defined function. GLB : It is used to call the Global function.
5. OPERATION 5.1 Power Turn on the controller power after all domes have initialized (wait at least 30 seconds) 1. Input 12VDC 1A to the Cyber controller & junction box 2. Connect Cyber controller and the junction box by RJ-45 Cable. BOOTLOADER VXX DVR & DOME 38400 PO (ID:01) & MATRIX H/W VER : VX.XX S/W VER : VX.
5. OPERATION * How to control On-Screen Menu Utility Action Function SETUP button Call the controller SETUP menu. Joystick right Go into the sub-menu items or select current item. Navigate the cursor up or down. Go to previous or next item. Joystick up/down Twist the Joystick Up count/down count CLR,ESC button Exit without saving. Go to previous menu. ENT button Save & Exit 5.3 SYSTEM SETUP Press SETUP button to setup the system of the controller. Below screen shows the controller setup menu. 1.
5. OPERATION 5.3.2 PASSWORD SETUP When you want to change the password, you can change the password in password setup menu. The unit requires the initial password before operation. The factory default password is 8888. CURRENT PASSWORD INPUT? : NEW PASSWORD INPUT? : CONFIRM PASSWORD INPUT? : ① Input the current password and Press ENT button. ② Input the new password and Press ENT button. ③ Input the new password again and Press ENT button.
5. OPERATION 5.3.3 BACKLIGHT TIME SETUP BACKLIGHT TIME: 011 (11~255 SECS) While the Cyber controller is in idle mode, The backlight will be turned off automatically INPUT? : 1: SAVE You may determine backlight turn-on time. 2: EXIT after backlight time. 5.3.4 FACTORY DEFAULT This all data is initialized. DO YOU WANT TO INITIALIZE ALL DATA? 1: YES Note : Be careful to select this mode since you can not revert the current data forever. 2: NO 5.3.
5. OPERATION 5.3.6 CAMERA SETUP Set up Camera ID Range, the Protocol , Baud Rate of the Camera, and Output Port. You can select Individual Setup or Whole Setup. Navigate the Cursor by pushing the joy stick up or down. Cursor moves to the desired position. 1 CAM ID Setting: You can select the camera ID which you need to choose from CAM ID to CAM ID. ○ Input the Camera ID number and Press ENT → CAM ID:[001 – 001] COMM.:CYBER SCAN I Push the joystick right. → CAM ID:[999 -– 999] COMM.
5. OPERATION 4 PORT Setting: In the Camera ID Range, You need to select the port. To navigate and choose the ○ Baud Rate, push the joystick left/right or twist the joy stick clockwise/counterclockwise. If you set the controller to RS-232, controller sends the data through the RS-232 port. If you choose RS485/422, it sends the Communication protocol through the OUT port. CAM ID:[999 – 999] COMM.:CYBER SCAN I BAUD :9600 BPS Push the joystick left/right or twist the joystick clockwise/counterclockwise.
5. OPERATION 5.3.7 DVR SETUP Set up DVR ID Range, the Protocol , Baud Rate of the DVR, and Output Port. You can select Individual Setup or Whole Setup. Navigate the Cursor by pushing the joy stick up or down. Cursor moves to the desired position. 1 DVR ID Setting : You can select the DVR ID which you want to set from DVR ID to DVR ID. ○ Input the Camera ID number and Press ENT → DVR ID:[001 – 001] COMM.:ENBEDDED DVR Push the joystick right. → DVR ID:[255 -– 255] COMM.
5. OPERATION 4 PORT Setting : In the DVR ID Range, You need to select the port. To navigate and choose the ○ Baud Rate, push the joystick left/right or twist the joy stick clockwise/counterclockwise. If you set the controller to RS-232, controller sends the protocol through the RS-232 port. If you choose RS-485/422, it sends the Communication protocol through the OUT port. DVR ID:[255 – 255] COMM.:EMBEDDED DVR BAUD :9600 BPS Push the joystick left/right or twist the joy stick clockwise/counterclockwise.
5. OPERATION 5.4 LOCK If you don’t want another person (not authorized) to manipulate the controller, you can lock the Cyber controller by pressing LOCK button. 5.4.1 Lock Setting Input the current password and Press ENT DVR:001 CAM:0001 INPUT? : MON:001 PRST:319 CS-I:9600 Press LOCK LOCK SETTING? : INPUT? DISPLAY LOCK SETTING? : LOCK MODE CORRECT PASSWORD INPUT? 5.4.
6. DIMENSION A. Cyber Controller B.
7.
APPENDIX B - The List of GLB(Short) Key If you use Cyber Scan dome camera and Cyber controller, you can use the following GLB short cut key for the easy operations without accessing the main menu of the dome unit. (Cyber Scan protocol only) Note : Press GLB button, after press the numeric button. This function is available subject to Global mode on, in the main menu. GLB Key Function On/Off RMK 1.
APPENDIX B - The List of GLB(Short) Key 77 Area Title On/Off Toggle 78 Operation Title On/Off Toggle 79 Flag Display On/Off Toggle 80 Time Display On/Off Toggle Flip Off 3.
APPENDIX B - Trouble Shooting If problems occur, verify the installation of the camera with the instructions in this manual and with other operating equipment. Isolate the problem to the specific pieces of equipment in the system and refer to the equipment manual for further in formation. Problem If you forget the password Possible Solution a. Press 5 button then DVR button when you forget the password once the controller is turned off then on. The controller will be initialized to Default Password, 8888.
APPENDIX C-OPTIONAL ITEM A. Cyber Scan Dome Camera C. Digital Video Recorder B. Cyber Scan Pre-Pack Dome Camera D.
MEMO 31
