Installation Instructions

Contractors Wardrobe
®
, 26121 Avenue Hall, Valencia, CA 91355 | Phone: [phone] Fax: [phone] | CwDoors.com
Zephyr
™
-PRIN-2830-0620
3
NO. QTY. PART # PART DESCRIPTION
Header Assembly
1 1 ALUM-7740* Header
2L 1 ALUM-7750* Left Wall Jamb
2R Right Wall Jamb
3 1 ALUM-7760* Curb
4 1 VINY-118 5CL Clear Panel Glide Strip
(Pre-Installed)
5 4 HARD-2045 Panel Locator/Bumper
6 4 FAST-1365* #8 x 1-1/2” PH SMS Screw
7 2 FAST-1250* #8 x 1-1/2” FH SMS Screw
8 6 FAST-1440 Screw Anchor
9 4
HARD-3080*
Panel Hanger Assembly
9a 4
HARD-3085* T-Bracket Housing
9b 8 HARD-2065BL Wheel, Ball Bearing
9c
4
#8-32 x 1/2” PFH Screw
9d
4 HARD-4020 Bushing
9e
4 HARD-4005 1/4” (6mm) Gasket
4 HARD-4010 5/16” (8mm) Gasket
9f
4 HARD-3090* Adjustable Cam
9g
1 HARD-4025 2-Pin Cam Wrench
9h
4 HARD-4000* L-Bracket Housing
9i
4 HARD-3095* Cam Cover
10
4
HARD-2040 Soft Close includes
two plates, three screws
Glass
11 1 Outside Door Panel
12 1 Inside Door Panel
13 1** HARD-2000* 1/4” (6mm) Center Guide
HARD-2005* 5/16” (8mm) Center Guide
Hardware
14 1** TBC-SLN3-20SK* Solana Towel Bar Combo
(shown)
TBC-VCT5-20BK* Victoria Towel Bar Combo
TBC-CTN3-20BK* Canton Towel Bar Combo
*When reordering the part please indicate the SIZE and/or FINISH
**Based on your selection
DO NOT use a razor blade to cut open the paper
wrapping as you may scratch the contents.
DO NOT REMOVE your old shower door until you
check that your new shower door kit is the right size
for your shower and that all the proper parts are in
the box or hardware bag.
Congratulations on purchasing your new Cw
®
tub/
shower enclosure. Now that you have opened the
package, we want you to verify that you have all the
necessary hardware supplied with your enclosure.
Please read and understand these instructions in their
entirety prior to assembly, installation and operation.
Use a level to check that the tub/shower sill is
reasonably level – not more than 1/8” out of level from
side to side. If the sill is out of level more than 1/8”,
you will need to order a custom-mitered filler that fits
under the Curb. This will level the Curb correctly. In the
absence of leveling the Curb with a mitered filler, and
depending upon the out of level amount, the Panels
may not stay in a closed or open position.
Use a level to check that the walls of the enclosure are
plumb – not more than 3/8” out of plumb. If the walls
are out of plumb by more than 3/8”, you will need
to order a custom-mitered filler that fits behind the
Wall Jamb. In the absence of a plumb Wall Jamb, and
depending upon the out of plumb amount, the Panels
may not close correctly.
To order custom-mitered filler for your Curb or Wall
Jambs, please contact customer service at your
original purchase location.
Before beginning assembly of the product, make sure
all parts are present. Compare parts with the parts list.
If any parts are missing or damaged, do not attempt to
assemble the product. Contact our Customer Service
department with any questions or concerns you may
have about this product at 661.257.1177.
KEEP THE CORNER PROTECTORS
ON THE GLASS DURING
INSTALL ATION
Parts list