Surfliner Illustrated Installation Instructions ™ Contractors Wardrobe®, 26121 Avenue Hall, Valencia, CA 91355 | Phone: 661.257.1177 Fax: 661.257.4907 | CwDoors.
Surfliner™ Outside Panel HangerAssembly (#10) Illustrated Parts Breakdown (IPB) 10b Shown with Solana Towel Bar 10d aa 10c 11 10a dd 8 Inside Panel Hanger Assembly (#9) bb 7 cc 9c dd aa 9b 6 1 bb 13 cc 9d 5 10 7 2L 12 9a 14 9 13 12 15 8 5 6 Right Wall Mount (#12) 6 17 2R 13 12 13 12 5 12a 13 5 16 6 3 13 4 2 Surfliner™-PRIN-2820-0620 Contractors Wardrobe , 26121 Avenue Hall, Valencia, CA 91355 | Phone: 661.257.1177 Fax: 661.257.4907 | CwDoors.
Parts list NO. QTY.
C. Tool checklist (included): KNOW YOUR WIDTH d d Width D. D. a A. a A. 3 Hex keys Tool checklist (not included): Height Height Height Height • TUB Width b B. • Level • Electric drill • 1/8” drill bit (for fiberglass stall) b c B. C. c C. 3/16” masonry drill bit (for tile stall) • Pencil • Fine metal file • Miter box & hacksaw with 32 tooth blade • Caulking gun and clear tub/tile silicone • Wire cutters • Tape measure • Painters tape D. A.
Step 3 C. Locate the Curb. Remove the Panel Glide Strip from the Curb (See Figure 3). Note: The Aerial™ comes with two Wall Jambs. One is notched for the left wall, the other is notched for the right wall. Each Wall Jamb is marked clearly on the bottom back side: “L” for left, “R” for right. Inside enclosure Painter’s tape A. Locate the left Wall Jamb. Curb (#3) B. Place the left Wall Jamb against the left wall and slip the bottom of the Wall Jamb over the Curb.
Step 4 Installing the Panel Locator/Bumper Step 5 Installing the Wall Mount Brackets A. Remove the Latch from Wall Mount Bracket (See Figure 5). See Figure 4 to position the Panel Locators. Secure with #8 x 1-1/2” PH SMS Screws. Panel Locator/ Bumper (#5) Right Wall Mount Bracket (#12) Right Wall Mount Bracket Latch (#12a) 723 9,(: 6&$/( Panel Locator/ Bumper (#5) Figure 5 ,62 9,(: 6&$/( B. Place Right Wall Mount Bracket on top of the right Wall Jamb.
Right Wall Mount Bracket (#12) #8 1-1/2” flat head plain screw (#7) Right Wall Mount Latch (#12a) Hex Key 723 9,(: 6&$/( Right Wall Jamb (#2R) 6& 6,'( 9,(: 6&$/( Figure 7 )5217 9,(: 6&$/( Step 6 %$&. 9,(: 6&$/( Installing the Header &Z A. Using the tape measure, measure the width from inside the Right and Left Wall Mount Brackets. 7,7/( 352326(' /()7 02' Figure 8 B. Locate the Header. Using the miter box and hacksaw cut the header to the length you just measured.
Step 7 B. Hanging the Inside Panel in the C-Rail Header Installing the Glass Panels may be easier if you have someone assisting you. Always wear gloves and safety glasses whenever handling glass. Installing the Inside Panel A. Attaching the Inside Panel Hanger Assembly 1. Insert Cam Bushings into the hole at the top of the Inside Glass Panel. Note: Take extra care in handling the Glass Panels.
of the Adjustable Cam to turn it. This moves the Panel up or down in the Hanger Assembly (See Figure 11). Step 8 WARNING! DO NOT ATTEMPT TO LOCK THE CENTER GUIDE IN PLACE UNTIL YOU ARE READY TO INSTALL IT! Once the Center Guide is in place the shower Door Panels will be extremely difficult to remove, and adjusting or removing the Center Guide will be nearly impossible.
E. Slide the Center Guide under the Door Panel. Center the Center Guide on the pencil mark you made (See Figure 13b). Press the Center Guide onto the Curb and lock it into position by pressing firmly on the back edge of the Center Guide as shown in Figure 13c. You should feel it lock into place. If the Center Guide does not lock into position easily, it may be necessary to press firmly on one end to start the process and work along the back of the Center Guide in order to lock it into place. Step 9 A.
B. Hanging the Outside Panel on the Header freely (See Figure 15). Installing the Door Panels may be easier if you have someone assisting you. Always wear gloves and safety glasses whenever handling glass. Note: If you have a Soft Close installed in your Header, you will need to move the Soft Close mechanisms inside the Header all the way to the ends (two on each end of the Header track), so they are out of the way when attaching the Soft Close Catches.
A. Installing the Towel Bar to the Outside Panel tighten with the Hex Key. Do not over tighten. 4. Repeat Step 9, B3 with second Outside Panel Hanger Assembly. This will secure the Outside Panel to the Header. Do not over tighten the screw. 1. Locate the Towel Bar Kit parts for the Outside Door including a Towel Bar, two Towel Bar Adapters, two Recessed Finger Pulls, four Washers and two Bushings. Refer to Figure 18-19 to help identify these parts for your hardware style. C.
Knob and Recessed Finger Pull Assembly Towel Bar Assembly NO. QTY. PART DESCRIPTION NO. QTY. 17 1 Towel Bar 17a 4 PART DESCRIPTION Washer 17a 4 Washer 17b 2 Bushing 17b 2 Bushing 17d 1 Recessed Finger Pull 17c 2 Towel Bar Adapter 17e 1 Knob 17d 2 Recessed Finger Pull 17f 1 End Cap 17g 1 Recessed Finger Pull Note: The Inside Door Knob Assembly is included in the Towel Bar Combo. All part numbers can be found on the parts list on page 3.
C. Installing the Knob and Pull on the Inside Door Panel Step 11 Silicone sealing the enclosure Using a caulking gun and clear silicone, seal inside your shower enclosure in the following areas: 1. Slide the Inside Door Panel towards the shower head about 5” to 6” for the next step. 2. Locate the Knob and Recessed Finger Pull. Refer to Figure 19 to help identify the parts. 3.
Your Style. Our Quality. CwDoors.
