Specifications

22 / CUTTERS EDGE FIRE RESCUE SAWS
ENGINE
TYPE: Single-cylinder 2-cycle, with loop
scavenging
DISPLACEMENT: 4.0 cu. in. (65.1 cc)
BORE: 1.89 in. (48mm)
STROKE: 1.4 in. (36mm)
COMPRESSION RATIO: 9.4:1 (±.3)
BEARINGS: Heavy-duty deep-groove ball bear-
i ngs on crankshaft, needle cage bearings on
connecting rod, piston pin and clutch
CYLINDER/PISTON: Open ported, single ring
design with four transfer ports
CYLINDER MATERIAL: Nikasil
MAX ENGINE SPEED: No load... 12,500 RPM
IGNITION SYSTEM
TYPE: Electronic, one piece modular, CD
BRAND: FHP
SPARK PLUG: Champion CJ7Y or equivalent
GAP: 0.020 in. (0.5mm)
STARTING SYSTEM
ONE STEP STARTING SYSTEM WITH
COMPRESSION RELEASE
Comprised Of...
Momentary contact switch
Combined choke/throttle lock with throttle safety
guard
AIR FILTRATION
SYSTEM: "RAM-AIR" with metered stack
TYPE: 2-stage, oil tack barrier, external mount
SURFACE AREA: 154 sq.in. "First Stage"
29 sq.in. "Second Stage"
FUEL & ENGINE LUBRICATION
GASOLINE OCTANE RATING: Use 90 octane
or higher
FUEL MIX OIURATIO:
With Cutters Edge Synthetic Oil: ...100:1
If petroleum base 2-cycle oil used: ...50:1
FUEL TANK CAPACITY: 26.8 fl. oz. (0.77 liters)
CARBURETOR ISOLATION
Designed to eliminate Vapor-lock and vibration
TYPE: Air gap isolation and Bakeolite insulation
DRIVE SYSTEM
TYPE: Inboard, 3-shoe centrifugal clutch
STYLE: Rim & Drum System
Radically Ported to keep rim free of tar & debris
build-up... free floating to keep chain in perfect
alignment with bar groove
SIZE: .404 by 7 tooth
CHAIN SPEED: No Load chain speed 98.5
FPS (feet per second)
GUIDE BAR
TYPE: Solid one piece construction, No
Rivets/No Laminates... 20" and 16" slotted for
Guard/Depth Gauge
MATERIAL
TITANIUM ALLOY, 7mm thick;
STYLE: Roller Blade/Speed Ring with sealed
bearing
CUTTING LENGTHS: 20", 16" and 12"
SIZE: .404 Pitch.063 Gauge
CUTTING CHAIN
CUTTERS EDGE "BULLET CHAIN"®
TYPE: Carbide Tipped "BULLET CHAIN"
SIZE: .404 pitch .063 Gauge
CUTTERS EDGE FIRE RESCUE SAW SPECIFICATIONS
CUTTING CHAIN LUBRICATION
SYSTEM
TYPE: Fully automatic, adjustable
DRIVE SYSTEM: Geared to Centrifugal Clutch
LUBRICANT: Cutters Edge "High Tack" Bar &
Chain Oil or high quality bar & chain oil
OIL TANK CAPACITY: 14.24 fl. oz. (0.42 liters)
HANDLES
TYPE: Front/Top... Full Wrap (For ease of use
with gloves, from either side of saw)
Back... Flared base for kickback guard Full iso-
l ation anti-vibration
VIBRATION LEVELS
*FRONT HANDLE M/S2 :3,6
*REAR HANDLE M/S2 : 5, 7
(*see Note 2)
SILENCING
MUFFLER: Oversize, top ported, low restriction
with fire screen
**NOISE LEVEL: 102dB(A) at maximum output
(**see Note 1)
GUARD/DEFLECTOR
TYPE: Aluminum front mount to cover muffler
and control air-flow for delivery of cleaner, cool-
er air to cylinder heat exchangers... (Keeps
engine running cooler and reduces mainte-
nance)
CHAIN BRAKE
TYPE: Inertia Activated
STYLE: Free-Swinging Pendulum
BREAKING TIME: <0.20 second
GUARD/DEPTH GAUGE® (Optional)
FUNCTION: Covers all the cutting chain, allows
saw operator to set depth of cut to avoid cutting
structural members
MATERIAL: Anodized aluminum
TYPE: D6 for 16" saw... D8 for 20" saw
3-point mount, positive lock with depth of cut
scale
DEPTH OF CUT: D6 = 6" D8 = 8"
WEIGHT
POWERHEAD ONLY: 13.9 lbs. (Dry Weight)
CE-2065RS-12": 21.0 lbs.
CE-2065RS-16": 21.5 lbs.
CE-2065RS-20":
22.0 lbs.
CE-2065RS/D6: 24.0 lbs.
CE-2065RS/D8: 24.5 lbs.
STANDARD ACCESSORIES
ACCESSORIES INCLUDED WITH ALL FIRE
RESCUE SAWS
"Scrench" holder and "Scrench" tool, complete
tool kit including grease gun and packet of
grease, complete manuals, filter cleaner and
filter oil kit, Cutters Edge 2-cycle oil mix, Cutters
Edge bar & chain oil, bar scabbard (saws with-
out D6 and D8 only)
I NCLUDED WITH D6 & D8 SAWS ONLY...
Training video for Guard/Depth Gauge assem-
bly, operation and maintenance
Specifications are subject to change without notice
ENGINE
TYPE: Single-cylinder 2-cycle, with loop
scavenging
DISPLACEMENT: 4.3 cu. in. (70.7cc)
BORE: 1.97 in. (50mm)
STROKE: 1.4 in. (36mm)
COMPRESSION RATIO: 10.2:1 (+.3)
BEARINGS: Heavy-duty deep-groove ball bear-
i ngs on crankshaft, needle cage bearings on
connecting rod, piston pin and clutch
CYLINDER/PISTON: Closed ported, single ring
design with four transfer ports
CYLINDER MATERIAL: Nikasil
MAX ENGINE SPEED: No load... 13,500 RPM
IGNITION SYSTEM
TYPE: Electronic, one piece modular, CD
BRAND: FHP
SPARK PLUG: Champion CJ7Y or equivalent
GAP: 0.020 in. (0.5mm)
STARTING SYSTEM
ONE STEP STARTING SYSTEM WITH
COMPRESSION RELEASE
Comprised Of...
Momentary contact switch
Combined choke/throttle lock with throttle safety
guard
AIR FILTRATION
SYSTEM: "RAM-AIR" with metered stack
TYPE: 2-stage, oil tack barrier, external mount
SURFACE AREA: 154 sq.in. "First Stage"
29 sq.in. "Second Stage"
FUEL & ENGINE LUBRICATION
GASOLINE OCTANE RATING: Use 90 octane
or higher
FUEL MIX OIL/RATIO:
With Cutters Edge Synthetic Oil: ...100:1
If petroleum base 2-cycle oil used: ...50:1
FUEL TANK CAPACITY: 26.8 fl. oz. (0.77 liters)
CARBURETOR ISOLATION
Designed to eliminate Vapor-lock
TYPE: Air gap isolation and Bakeolite insulation
DRIVE SYSTEM
TYPE: Inboard, 3-shoe centrifugal clutch
STYLE: Rim & Drum System
Radically Ported to keep rim free of tar & debris
build-up... free floating to keep chain in perfect
alignment with bar groove
SIZE: .404 by 7 tooth
CHAIN SPEED: No Load chain speed 106.4
FPS (feet per second)
GUIDE BAR
TYPE: Solid one piece construction, No
Rivets/No Laminates... 20" and 16" slotted for
Guard/Depth Gauge
MATERIAL
TITANIUM ALLOY, 7mm thick;
STYLE: Roller Blade/Speed Ring with sealed
bearing
CUTTING LENGTHS: 20" 16" and 12"
SIZE: .404 Pitch .063 Gauge
CUTTING CHAIN
CUTTERS EDGE "BULLET CHAIN"0
TYPE: Carbide Tipped "BULLET CHAIN"®
SIZE: .404 pitch .063 Gauge
Cutter's Edge, DB Guard/Depth Gauge® and BULLET CHAINS are registered trademarks of Edge Industries Inc, Pat. 5,056,395 5,156,156 P.O. Box 1179. Julian, CA 92036 USA
CUTTING CHAIN LUBRICATION
SYSTEM
TYPE: Fully automatic, adjustable
DRIVE SYSTEM: Geared To Centrifugal Clutch
LUBRICANT: Cutters Edge "High Tack" Bar &
Chain Oil or high quality bar & chain oil
OIL TANK CAPACITY: 14.24 fl. oz. (0.42 liters)
HANDLES
TYPE: Front/Top... Full Wrap (For ease of use
with gloves, from either side of saw)
Back... Flared base for kickback guard Full iso-
l ation anti-vibration
VIBRATION LEVELS
*FRONT HANDLE M/S2 :4,6
*REAR HANDLE M/S2 :
5, 2
(*see Note 2)
SILENCING
MUFFLER: Oversize, top ported, low restriction
with fire screen
**NOISE LEVEL: 104dB(A) at maximum output
(*see Note 1)
GUARD/DEFLECTOR
TYPE: Aluminum front mount to cover muffler
and control air-flow for delivery of cleaner, cool-
er air to cylinder heat exchangers... (Keeps
engine running cooler and reduces mainte-
nance)
CHAIN BRAKE
TYPE: Inertia Activated
STYLE: Free-Swinging Pendulum
BREAKING TIME: <0.20 second
GUARD/DEPTH GAUGE® (Optional)
FUNCTION: Covers all the cutting chain, allows
saw operator to set depth of cut to avoid cutting
structural members
MATERIAL: Anodized aluminum
TYPE: D6 for 16" saw... D8 for 20" saw
3-point mount, positive lock with depth of cut
scale
DEPTH OF CUT: D6 = 6" D8 = 8"
WEIGHT
POWERHEAD ONLY: 13.9 lbs. (Dry Weight)
CE-2071 RS-12": 21.0 lbs.
CE-2071 RS-16": 21.5 lbs.
CE-2071 RS-20": 22.0 lbs.
CE-2071 RS/D6: 24.0 lbs.
CE-2071 RS/D8: 24.5 lbs.
STANDARD ACCESSORIES
ACCESSORIES INCLUDED WITH ALL FIRE
RESCUE SAWS
"Scrench" holder and "Scrench" tool, complete
tool kit including grease gun and packet of
grease, complete manuals, filter cleaner and fil-
ter oil kit, Cutters Edge 2-cycle oil mix, Cutters
Edge bar & chain oil, bar scabbard (saws with-
out D6 or DS only)
I NCLUDED WITH D6 & D8 SAWS ONLY...
Training video for Guard/Depth Gauge assem-
bly, operation and maintenance
**Note 1:Equivalent noise level is, according to ISO 7182 and ISO 9207 calculated as the time-weighted energy total for
*Note 2: Equivalent vibration level is, according to ISO 7505, calculated as the time-weighted energy total for vibration
noise levels under various working conditions with the following time distribution'. 1/3 Idle, 1/3 full load, 1/3 full speed.
levels under various working conditions with the following time distribution: 1/3 mle, 1/3 full load, 1/3 full speed.
MODEL
CE-2065-RS
MODEL
CE-2071-RS