Installation Instructions

ManualsBrandsCustomCraft High Resolution ManualsAll Countertops & LaminateCustomCraft Countertops® 6' Golden Mascarello Left Miter Laminate Countertop

APPLYING LOOSE BACKSPLASH

Trace the contour of the wall

to the top of the backsplash

with marking utensil.

Sand non-laminated side

of the backsplash to the

marked wall contour.

Dab color-matched caulk

along the top, back, and

underside of loose backsplash.

Secure to the top and wall

(Preferably with painters tape)

until caulk dries. Place a

bead of color-matched caulk

between the top of backsplash

and wall, and between the

backsplash & countertop to

seal from moisture.

COLOR-MATCH SEAM FILLER/REPAIRER INSTRUCTIONS

CARE AND MAINTENANCE

Fig. 11

1. Prepare the surface of the area to be repaired by exposing the backer or substrate. Thoroughly clean the area with seam ller/repairer

solvent (acetone). It is important to use 100% acetone when working with the product.

2. Squeeze the seam ller/repairer onto you nger. Draw the repairer across the area to be lled with your nger. This action will force the

material down into the area to be lled. Repeat this action several times until the material starts to harden.

3. Remove any excess material from around the area being lled with the leading edge of laminate sample square provided. Wait

approximately 15 minutes to allow the product to completely dry.

4. Seam ller/repairer is a solvent based product and some shrinkage will occur. If the material has shrunk below the surface being repaired,

simply repeat steps 2 & 3 until the repair is satisfactory.

5. Use a clean cloth with seam ller/repairer solvent and light pressure to blend the material level with the surface.

This product has been designed to adhere to the back of HPL (high pressure laminate). The backer is either brown or black in color. It will also

adhere to particle board, medium density ber board, and plywood. It is not designed to adhere to the actual color layer or surface of laminates.

1. Wash the surface with mild dish washing liquid or powdered detergent; add warm water. Use a soft dish cloth. Rinse with warm water and dry

with cloth. Water is generally all that is needed. A quick wipe will clean most stains.

2. For harder-to-remove spots, use an all-purpose cleaner or bathroom cleanser. Follow the manufacturer’s instructions. Rinse with warm water

and dry with a soft cloth.

(NOTE: Do not use cleaners that contain harsh acids or abrasives.)

3. For stubborn spots, make a paste with baking soda and water. The paste will be slightly abrasive. Work carefully to keep from damaging the

surface you are cleaning. Dip a soft bristle brush into the paste to cover the bristles. Gently rub the spot with the brush, moving in a circular

motion and pressing very lightly. You may also use a Magic Eraser stain remover following the manufacturer’s instructions for stubborn stains.

CAULK BACKSPLASH

(NOTE: Color-matched caulk; included in installation kit sold separately)

• Use color-matched caulk to seal around backsplash

and walls (Fig. 11).

• Color-Match Adhesive & Caulk will dry darker.

• Color-Match Adhesive & Caulk is non-toxic, non-

ammable, and mildew resistant.

• Manufacturer makes no warranty of any kind, expressed

or implied, concerning the use of this product. User

assumes all risk of handling or use whether in accordance

with the directions or not.

• Clean countertops per guidelines in the Care and

Maintenance section.

1. Knead the caulk tube before using.

2. Surfaces must be clean and free of dust, dirt, oil and

other substances.

3. Place bead of adhesive caulk to seal where backsplash

meets wall (Fig 11).

4. Using moderate pressure and moist nger, remove

excess caulk (Product will shrink as it cures).

Backsplash