User manual

NOTE:
(1)
: This parameter is used to identify univocally the USB printer by a numerical address code, if on the PC are connected
two printers that are the same models for example two USB printers.
(2)
: This parameter is displayed if the printer emulation is set to KPM54.
(3)
: This parameter is displayed if the printer emulation is set to ESC/POS
TM
.
(4)
: If the “Notch Position” parameter is set to “Disabled” this parameter doesn’t appear in the “Printer Setup”.
1.3 CONFIGURATION
This printer permits the confi guration of default parameters. The printer’s confi gurable parameters are:
Printer Emulation: • ESC/POS
D
, SVELTA, KPM54.
Baud Rate :• 115200
D
, 57600, 38400, 19200, 9600, 4800, 2400, 1200.
Data length : • 7, 8
D
bits/car.
Parity :• None
D
, even, odd.
Handshaking :• XON/XOFF, Hardware
D
.
Busy condition : • RXFull
D
, OffLine/RXFull.
USB Address Number :• 0
D
, 1, 2, 3, 4, 5, 6, 7, 8, 9.
Print mode:• Normal
D
or Reverse.
Height Mode •
(2)
: x 1
D
, x 2, x 4.
Width Mode •
(2)
: x 1
D
, x 2, x 4.
Justifi cation •
(2)
: Left
D
, Centered or Right.
Character set •
(2)
: U.S.A.
D
, Standard Europe.
Panel Buttons •
(2)
: Enabled
D
, Disabled.
Paperend Sensor:• Enabled, Disabled
D
.
Autofeed:• CR disabled
D
, CR enabled.
Chars/Inch: • A=11 B=15 cpi, A=15 B=20 cpi
D
.
Speed/Quality :• Normal, High Speed
D
.
Paper width• : 20mm, 22mm, 24mm, 26mm, 28mm, 30mm, 32mm, 34mm, 36mm, 38mm, 40mm, 42mm,
44mm, 46mm, 48mm, 50mm, 52mm, 54mm
D
.
Paper Threshold•
(5)
: 30%, 40%, 50%, 60%
D
, 70%, 80%, 90%.
Notch Position•
(6)
: Disabled
D
, Down Mobile, Tr. Side, Up Side.
Notch Threshold•
(7)
: 30%, 40%
D
, 50%, 60%, 70%, 80%, 90%.
Notch Distance Sign•
(4)
: +
D
, -
Notch Distance [mm x 100]•
(4)(8)
: 0
D
, 1, 2, 3, 4, 5, 6, 7, 8, 9.
Notch Distance [mm x 10]•
(4)(8)
: 0
D
, 1, 2, 3, 4, 5, 6, 7, 8, 9.
Notch Distance [mm x 1]•
(4)(8)
: 0
D
, 1, 2, 3, 4, 5, 6, 7, 8, 9.
Notch Distance [mm x .1]•
(4)(8)
: 0
D
, 1, 2, 3, 4, 5, 6, 7, 8, 9.
Print Density:• -50%, -37%, -25%, -12%, 0
D
,+12%, +25%, +37%, +50%.
General notes:
The parameters marked with the symbol
D
are the default values.
Settings remain active even after the printer has been turned off.
NOTE:
(5)
: This parameter indicates the threshold value under the sensor detect the paper.
(6)
: This parameter sets which sensor is used as notch sensor. There are two sensor operating mode: refl ection or trans-
parence.
(7)
: This parameter is used to detect the presence of the notch. In order to better identify the optimum threshold for the
paper being used, a paper characterization function is also available in the setup.
(8)
: The “Notch distance” parameter represents the distance in mm from the upper margin of the ticket to the black mark
on the ticket. For example, to set notch distance to 15 mm, modify the following parameters in order to obtain the desired
values as indicated :
Notch Dist. [mm x 100] : 0
Notch Dist. [mm x 10] : 1
Notch Dist. [mm x 1] : 5
Notch Dist. [mm x .1] : 0
The settings made are stored in EEPROM (nonvolatile memory).
1. INSTALLATION AND USE
User Manual KPM150 1-3