TDS

8850 N.W. 79th Avenue Miami, Florida 33166 PH 800/826-6852 FAX [phone] www.jamoinc.com
FITNESS ARE HEREBY DISCLAIMED. The suitability of a
product for an intended use shall be solely up to the user.
Manufacturer assumes no liability for consequential
damages. Its liability shall in no event exceed the purchase
price of the materials supplied by it. No person has the
authority to change these items and there are no warranties
except herein stated.
Caution
Contains Portland cement. Wear rubber gloves and eye
protection. Avoid eye contact or prolonged contact with
skin. Wash thoroughly after handling. If eye contact occurs,
flush with water for 15 minutes. Consult a physician
immediately.
WARNING! Do Not Breathe Dust! This product contains
Free Silica which may cause cancer or delayed lung injury
(Silicosis). Wear approved respirator in dusty areas. See
Material Safety Data Sheet for detailed information.
KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE
INTERNALLY. STORE IN COOL, DRY AREA.
Application
INSTALLATION TO CONFORM TO ANSI A108.5. Use
proper sized notch trowel to ensure 100% coverage under
tiles. Use a 1/4" x 3/8" x 1/4" (6 x 9.5 x 6 mm) square-notch
trowel when setting tile larger than 12" x 12" (30 x 30 cm).
Using flat side of trowel, apply skim coat of mortar to the
surface. Apply additional mortar with notched side of trowel
held at a 45° angle to the surface, combing in one direction.
Press tile firmly into place in a perpendicular motion across
ridges, moving back and forth. Perpendicular pressing
flattens ridges and closes valleys allowing maximum
coverage. With some tile, back buttering is advisable.
Adjust tile promptly and beat in with block and rubber
mallet. Mortar can be applied up to 1/4” (6 mm) thick after
beat in. For thicker applications, use a medium bed mortar.
Periodically pull up a tile and check the back to ensure
complete coverage with the adhesive. Do not spread more
material than can be tiled in 15 minutes or while material
has wet tack (sticky to the touch). If material has skinned
over (not sticky), recomb with notch trowel. If too dry,
remove and replace with fresh material. Material in bucket
will remain workable approximately 4 hours.
Coverage
90 - 100 sq. ft. per 50 lbs. (8.4 - 9.3 M
2
/22.68 kg) applied
with a 1/4" x 1/4" x 1/4" (6 x 6 x 6 mm) square-notch trowel.
60 - 70 sq. ft. per 50 lbs. (5.6 - 6.5 M
2
/22.68 kg) applied with
a 1/4" x 3/8" x 1/4" (6 x 9.5 x 6 mm) square-notch trowel.
Cleaning
Clean with water before material dries.
Curing and Grouting
Allow to dry for at least 24 hours before grouting or light
traffic depending upon temperature and humidity. Master
Color
®
Grout is recommended.
Warranty
Manufacturer warrants that should this product prove to be
defective material, it will replace the same or refund the
purchase price of the goods. THIS WARRANTY IS IN
PLACE OF ALL OTHER WARRANTS EXPRESS OR
IMPLIED. WARRANTIES OF MERCHANTABILITY AND OF
MULTI-PURPOSE FLEX
POLYMER-MODIFIED THIN-SET MORTAR
DSJ012 8/10R
Typical Value
Exceeds ANSI A118.4 and
A118.11 specifications
Open Time @ 70° F (21° C) 30 minutes
Adjustability @ 70° F (21° C) 30 - 35 minutes
Shear Bond Strength
Non-Vitreous Tile: 28 day dry cure
Bisque Tile 550 psi (38.7 kg/cm
2
)
Porcelain Tile 450 psi (31.6 kg/cm
2
)
Quarry Tile to Plywood 190 psi (13.4 kg/cm
2
)
SETTING PRODUCTS
Item Code Color Size Package
125133 Grey 50 pounds (22.68 kg) Bag
125003 White 50 pounds (22.68 kg) Bag
Technical Data
Ordering Information