Installation Instructions

App-Controlled for your vehicle
Smart Lighting
WARNING
• Never use the LED Innovation App while driving &
obey all traffic laws.
• This product is intended solely for the purpose of
decorative or off-road use. Check laws and/or
regulations in your state, county and/or municipality
regarding installation and use of this product. This
product is not DOT Approved.
• Do not install this product or run its wires near any
moving parts. Keep all wires and lighting units away
from excessively hot areas.
• 12 Volt use only. Product designed to draw up to
2.8 Amps.
BEFORE INSTALLATION
It is recommended that you download the App, connect
and test your LED lighting kit before installation and
read all instructions carefully.
Model: 23191 FCC ID: 2ADMQ-23191-23192
A registered trademark of Bluetooth SIG, Inc
Smart Lighting
and download the App scan
the QR code with your
smartphone!
To learn more about
Download the
“LED INNOV”
App
TM
Visit our website at
ww w.causa.com
Customer Service:
1- 8 0 0 -962- 6 676
®
CUSTOM ACCESSORIES, INC.,
RICHMOND, IL 60071, USA
MADE IN CHINA © 01_2021 CA
ONE YEAR WARRANTY
We guarantee this product to be free of defects in
material and workmanship for a period of one year from
the date of purchase. If a defect in material or workman-
ship occurs, call Custom Accessories customer service at
[phone] for instructions on how to have it
replaced or repaired free of charge.
PROOF OF PURCHASE OR RECEIPTS MUST BE
PROVIDED FOR ANY/ALL REPLACED OR REPAIRED
ITEMS.
This guarantee does not cover normal damage to the
product that is not the result of a defect in materials or
workmanship such as, for example, normal wear and tear
or damage resulting from an accident. Shipment of any
product back to Custom Accessories is at the consumer’s
expense. Custom Accessories, Inc. limits its liability only
to the replacement of its products, not incidental or
consequential damages to other property. Some states
do not allow the exclusion or limitation of incidental or
consequential damages. This guarantee gives you
specific legal rights and you may also have other rights
which vary from state to state.
OPTIONAL HARDWIRE KIT
INSTALLATION INSTRUCTIONS:
1. Open the package and find the direct wire harness.
(included)
2. Run the wires toward a 12V power source.
(For example, a fuse box or light switch)
The circuit chosen must be able to supply 3 Amps.
3. Connect the (+) red wire to a (+) positive power
source that is switched (like a running light) so the
light strips will light only when the vehicle ignition is
turned on.
4. Or you can connect the red (+) positive wire to a
circuit with constant power and add your own switch
to turn it on and off. The LED INNOVATION APP
also includes a master ON/OFF switch.
5. Connect the black/red (-) negative wire to any clean,
metal ground.
6. Tuck and secure all wires.
For FCC matters please contact:
Custom Accessories Inc., 5900 Ami Drive, Richmond, IL 60071
Ph. # [phone]
FCC RF Radiation Exposure Statement
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure condition
without restriction.
To replace fuse, remove fuse and replace with like amperage.
Para cambiar el fusible, saque el fusible y reemplácelo con
uno de amperaje similar.
12v - 3 amp maximum
12v - 3 máximo de amperio
Mini blade fuse
Mini fusible De cuchilla
1' (30.48cm) Wire
3' (91cm) Wire
2' (61cm) Wire
2' (61cm) Wire
2' (61cm) Wire
2' (61cm) Wire
3' (91cm) Wire
3' (91cm) Wire
3' (91cm) Wire
Kit includes:
6Pc - 3M™ Tape 10 Cable Ties8 Screws
23191
EXTERIOR
LED POD KIT
INSTALLATION
1. Begin by laying out your new lighting system. Place your
Pod lights where you would like to install them and place
the 12V power wires near the power source to make sure
you have enough wire. You may power your lights using
the included trailer harness or 12V direct wire option.
2. Next, select a mounting location for the control box
while making sure you leave enough wire to reach both
the Pod lights and 12V power source. Clean the control
box installation surface thoroughly with alcohol and allow
to dry before installation. Install your control box using
the included two-sided tape and screws (if desired).
3. To install your LED Light Pods, you may use the included
3M double sided tape, the included screws or both.
Run your wires from each set of LED Light Pods to the
control box and plug them in. Tuck and secure all wires
with included cable ties.
4. If using the 12V trailer wiring harness to power your lights,
insert the trailer wiring harness into your trailer socket.
Tuck and secure all wires. Alternatively, you may use the
12V hardwire option.
(Follow the instructions on the next page)
5. Start your vehicle. Open the LED INNOV APP and choose
to connect to the “EXT HUB” 1 channel system.
Mobile phone must be within Bluetooth range.
(Approximately 30 feet from the control box)
6. You have now successfully installed your new lighting
system and are ready to customize it using the
LED INNOV APP. Please see the “Info” tab on your
LED INNOV APP for important tips and instructions.
FCC
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation. NOTE: This equipment has
been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
product. This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located
or operated in conjunction with any other antenna or
transmitter.