Specifications

5 - 9
MAINTENANCE
Read all of this manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notices, Cautions, Warnings, and Dangers.
5
To access the instructions remove three re-usable plastic rivets securing the controller
splash shield to the body and the controller. To remove the re-usable rivets, press the
center of the rivet with the vehicle key, when the center pin snaps into place the rivet can
be removed, repeat the process for each remaining rivet. Turn the splash shield over to
reveal the instructions for releasing the parking brake.
To reinstall the controller splash shield, position the splash shield by aligning the mount-
ing holes with the holes in the body, push the center pin of each rivet upward so that the
top of the pin is above the rivet head.
Place a rivet in each mounting hole of the controller splash shield and push down on the
center pin until the top of the pin is flush with the rivet head.
THIS PROCEDURE SHOULD ONLY BE PERFORMED BY QUALIFIED TRAINED PERSON-
NEL.
Make sure that the key is in the ’OFF’ position and the tires are chocked to prevent the vehicle moving; then perform
the following:
1. Locate the ’Auxiliary Power’ line (3) and remove the weather pack seal (4) from the connector.
2. Locate the ’Primary Power’ line connector (1) and disconnect it from line (2).
3. Connect the ’Auxiliary Power’ line (3) to the ’Primary Power’ line (1) which will release the brake. If the tires are not
chocked and the vehicle is not on flat ground the vehicle will move immediately.
4. Move the vehicle to desired, safe location and chock the tires immediately.
5. Disconnect the ’Auxiliary Power’ line (3) from the ’Primary Power’ line (1).
6. Connect the ’Primary Power’ line (1) to line (2).
7. Replace the weather pack seal (4) on the ’Auxiliary Power’ line connector (3).
609694
Failure to follow these instructions can result in DEATH or SERIOUS INJURY
THIS PROCEDURE SHOULD ONLY BE TO CLEAR VEHICLE FROM AN UNSAFE AREA AND BE PERFORMEDTHIS PR OCEDURE SHO ULD ONLY BE TO CL EAR VEHICLE FROM AN UNSA FE AREA AND BE P ERFORMED
ONLY BY QUALIFIED TRAINED PERSONNEL ONLY BY QUALIFIED T RAINED PERSO NNEL
In Case Of Total Power Loss And The ‘Run-tow’ Switch DOES NOT Release The Brake To Move The Vehicle: In Case Of Total Powe r Loss And Th e ‘Run-tow’ Sw itch DOES N OT Release T he Brake To Mo ve The Vehicle :
Turn the ignition key to the ‘OFF’ position and ‘chock’ tires to prevent inadvertent movement.Turn the ignition key to the ‘OFF’ position and ‘chock’ tires to prevent inadvertent moveme
n
t.
Connect ‘Auxiliary Power’ line (3) to ‘Primary Power’ line (1) which will release the brake. THIS WILLConnect ‘Auxiliary Power’ line (3) to ‘Primary Power’ line (1) whic h will release the brake. THIS WIL
L
CAUSE THE VEHICLE TO MOVE IMMEDIATELY IF NOT ON LEVEL GROUND.CAUSE THE VEHICLE TO MOVE IMMEDIATELY IF NOT ON LEVEL GROUND.
Move vehicle to desired location and park it properly on level ground, chock tires, IMMEDIATELYMove vehicle to des ired location and park it properly on level grou nd, chock tires, IMMEDIATELY
DISCONNECT ‘AUXILIARY POWER’ AND RECONNECT ‘PRIMARY POWER’ (1, 2) FOR SAFETYDISCONNECT ‘AUXILIARY POWER’ AND RECONNECT ‘PRIMARY
POWER’ (1
, 2) FOR SAFETY
AND TO AVOID BATTERY DRAIN.AND TO AVOID BATTERY DRAIN.
Reconnect the Weather Pack Seal (4) to the Auxiliary Power line (3) and perform required serviceReconne ct the Weather Pack Seal (4) to the Auxiliary Power line (3) and perform required service
procedures following all Safety guidelines as outlined in your repair manual.procedures followin g all Safety guidelines a s outlined in your repair manual.
Identify the ‘Auxiliary Power’ line (3) and remove the Weather Pack Seal (4) from the connector.Identify the ‘Auxil iary Power’ li ne (3) and remove the Weat her Pack Seal (4) from the connector.
Identify the ‘Primary Power’ line (1) connector and disconnect the line (2).Identify the ‘Prima ry Power’ line (1) connector and disconnect the line (2)
.
3
4
1
2
Controller Splash Shield