Curtron - MicroShield Users Guide and Installation Manual Curtron Products, A Senneca Company 11502 Century Blvd., Cincinnati, OH 45246 800.833.5005 www.curtronproducts.
TABLE OF CONTENTS PAGE 2---------------------------------------------------------------------------------------------------INDEX PAGE 3-------------------------------------------------------------------------------------------WARRANTY PAGE 4-8-------------------------------------------------------------------------INSTALLATION GUIDE PAGE 9---------------------------------------------------------------------------------------INITIAL SETUP PAGE 10-----------------------------MAGNETIC REED SWITCH MOUNTING INS
THIS WARRANTY CERTIFICATE TO BE RETAINED BY CUSTOMER WARRANTY GENERAL WARRANTY STATEMENT We warranty all Curtron products to be free from defects in material and workmanship under normal use and service. Our warranty covers the product only as to materials or workmanship and not for fitness for purpose or merchantability. In the event that products are found to be defective in materials or workmanship, the extent of our liability will be replacement of defective parts only.
INSTALLATION DIMENSION I I A Intake H Front View On/Off Switch J Model MCS-36 MCS-48 MCS-72 A B C D E F G H I J 900mm 1200mm 1800mm 95mm 95mm 95mm 347.5mm 347.5mm 695mm NA 295mm 190mm 347.5mm 347.5mm 695mm 46mm 100mm 230mm 215mm 123mm 2. INSTALLATION GUIDE Use the following guide when installing the Curtron MicroShield Air Barrier: 2.1 Secure the unit to a sturdy location to avoid vibration. (ie. solid beams above the door) Minimum clearance: 2.
A. Installing on a concrete wall 3.1 To remove the mounting plate Unscrew the screws on the back of the main using body to remove the mounting plate. 3.2 Installing the mounting bolts properly Determine where the bolt holes will be the mounting plate and pour epoxy into the bolt holes. Mounting Plate Concrete 13-15mm 40-50mm 3.3 When the epoxy 70 mm 3.
Step 2: Step 1: Wall Mounting Plate Extension Brackets Through bolt to Mullions. 1/4" Bolts Wall Mounting Plate r Bi-parting or swing doors with proximity sensors Bi-parting or swing doors with proximity sensors Step 3: Microshield Air Barrier 4" Door Mullion 5/16" x 2 1/2" Bolts Microshield Air Barrier Rear Mount 1/4" x 1" B Direction of Air Travel.
Step 1: Step 2: Mounting Plate Microshield Air Barrier DOOR DOOR Center the mounting plate on door and attach to wall. The bottom of the mounting plate should be no more than 3" above the door opening. Hang Microshield on mounting plate and secure in place with the bottom mounting screws provided DO NOT MOUNT THE AIR BARRIER IN THIS CONFIGURATION.
Aluminum Mullions MOUNTING MCS AIR BARRIER EXTENSION BRACKETS 5/16" x 2 1/2" Bolts 6" x 12" Extendable Mounting Bracket Back Mounting Plate 1/4" x 1" Bolts with flat washers Grounded Plug Intake Grill MCS Air Barrier MCS Top View Extension Brackets Rear Mounting Plate Air Barrie Fixing Screws 1/4" x 1" Bolts Door Mullion 5/16" x 2 1/2" Bolts Air Barrier Fixing Screw Rear Mount Extendable Mounting Bracket Door Sensor For every inch above the door header, move the Air Barrier into the building 1/
Setting up the Curtron MicroShield Air Barrier. Outside Inside Approx. 10-15 % of the airflow should be directed outwards in order to prevent cold draft by the floor. To find the airflow’s split location hold a handkerchief by the corner approximately 2-3 inches above the floor and move it gently back and forth in the doorway. The split location should be in the middle of the doorway or a little outside.
ELECTRICAL SCHEMATICS Figure 1 Two Speed Infrared Controlled Wiring Diagram OPERATION 1) Plug in Air Barrier 2) Turn on Air Barrier 3) Select the desired speed 4) Adjust diffuser (page 9) MAINTENANCE 1) Unplug the unit before performing any maintenance. 2) Clean the Air Barrier regularly. Use a damp cloth to wipe the exterior surfaces. DO NOT USE SOLVENTS OR OTHER HARSH CHEMICAL CLEANERS!!! 3) Blow or vacuum out the interior as required.
