Installation Guide

ManualsBrandsCURT ManualsAuto PartsRambler Tow Bar Lock Set

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND

CURT Manufacturing Inc. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing Inc. may repair or replace

the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement

of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.

For more information log onto www curtmfg com & for helpful towing tips log onto www hitchinfo com

MAKE: STYLE:

MI N.30

WARNI NG: NEVER EXCEED YOUR VEHI CLE MANUFACTURER'S RECOMMENDED TOWI NG CAPACI TY

WEI GHT CARRYI NG:

I NSTALLATI ON TI PS: I NSTALLATI ON TI ME:

I NSTALLATI ON REQUI RES:

VEHI CLE PHOTO:

HI TCH I LLUSTRATI ON:

REPRESENTATI VE PHOTO

MAKE SURE YOUR HI TCH MATCHES

LEVEL OF DI FFICULTY:

EASY

EASY MODERATE HARD

THE I NSTALL TI ME LISTED I S FOR PROFESSI ONAL

I NSTALLERS. IF YOU ARE HESI TANT TO UNDERTAKE

THI S TASK ON YOUR OWN, CONTACT AN AUTHORI ZED

CURT I NSTALLER FOR ADDI TI ONAL ASSI STANCE.

1. BEFORE YOU BEGI N I NSTALLATI ON, READ ALL

I NSTRUCTI ONS THOROUGHLY.

2. TO EASE I NSTALLATI ON, 2 PEOPLE MAY BE

REQUI RED.

3. USING PROPER TOOLS WI LL GREATLY I MPROVE

THE QUALI TY OF THE I NSTALL AND REDUCE THE

TI ME REQUI RED.

4. NEED HELP OR HAVE SOME QUESTI ONS?

CALL TECHNI CAL SUPPORT AT 800. 798.0813

Safety glasses should be

worn at all times w hile

installing t his product

YEARS: 2011- PRESENT NI SSAN MODEL:

JUKE ( AWD MODELS)

CROSSOVER

2,000

200

TRAI LER WEI GHT:

TONGUE WEI GHT:

11088 I NSTALLATI ON I NSTRUCTI ONS

LBS.

10 / 14 / 13

WARNI NG:

WE RECOMMEND THE USE OF 18 05 0 STABI LI ZI NG STRAPS FOR ALL NON- TRAI LER

( WHEEL- LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VI SI T US ONLI NE AT

WWW.CURTMFG.COM FOR FURTHER I NFORMATI ON.

RATCHET

TORQUE

WRENCH

SOCKET

17mm

18mm

20mm

SOCKET

EXTENSI ON

PRY BAR

PART REMOVAL

NO DRILLING REQUIRED

LOWER EXHAUST

REMOVE TOW LOOP

(EXCLUDES NISMO)

Summary of content (4 pages)

PAGE 1
1088 YEARS: 2011- PRESENT Safety glasses should be w orn at all times w hile installing t his product . I NSTALLATI ON I NSTRUCTI ONS MODEL: JUKE ( AWD MODELS) (EXCLUDES NISMO) MAKE: NI SSAN STYLE: CROSSOVER W ARNI NG: NEVER EXCEED YOUR VEHI CLE MANUFACTURER'S RECOMMENDED TOW I NG CAPACI TY WEI GHT CARRYI NG: I NSTALLATI ON TI ME: TRAI LER WEI GHT: TONGUE WEI GHT: 30 MI N. THE I NSTALL TI ME LI STED I S FOR PROFESSI ONAL I NSTALLERS.
PAGE 2
I NSTALLATI ON WALKTHROUGH: 1. Remove existing tow loop from passenger side of vehicle. Return tow loop and hardware to vehicle owner. Parts List ITEM QTY PART NUMBER DESCRIPTION 1 4 M10 - 1.25 x 30 HEX BOLT 2 4 7/16" CONICAL TOOTHED WASHER 3 4 M12-1.25 x 30mm HEX BOLT 4 4 1/2" CONICAL TOOTHED WASHER 4 3 2. Lower exhaust be removing (3) rubber isolators from the muffler. Use wire to hold up exhaust enough to prevent damage. 2 1 For more informat ion log onto ww w.curt mfg.
PAGE 3
I NSTALLATI ON WALKTHROUGH: 3. Raise hitch into position and secure with supplied hardware as shown. 5. Raise exhaust back into position. 4. Torque M12-1.25 hardware to  lb-ft and M10-1.25 hardware to 4 lb-ft. For more information log ont o ww w.curt mfg.com, & for helpful t owing t ips log ont o ww w.hitchinfo.
PAGE 4
NISSAN JUKE (AWD MODELS, EXCLUDING NISMO) 11088 10/14/13 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 2,000 LBS. TRAILER WEIGHT & 200 LBS. TONGUE WEIGHT. * * * DO N OT EX CEED V EH I CLE M AN U FACT U RER'S RECOM M EN DED T OWI NG CAPACIT Y .* * * WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.