Installation Guide

ManualsBrandsCurt ManualsAutomotiveCURT 60682 Double Lock EZr Gooseneck Hitch Kit Fits 2500 3500 Ram 2500 Ram 3500

Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or

consequential loss or damage.

DODGE 2500 / 3500 SHORT AND LONG BED

7/18/2014

**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!**

60660 SUBKIT

PAGE 1 OF 5

WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME

MODELS MAY REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE

BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB. ON TWO WHEEL DRIVE TRUCKS A CLEARANCE CHECK MUST BE PERFORMED

WHEN TRUCK IS LOADED AND UNLOADED TO VERIFY THE INVERTED BALL WILL NOT INTERFERE WITH THE TOP OF THE DIFFERENTIAL

SUBKIT WEIGHT:

LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

PERIODICALLY CHECK THIS GOOSENECK HITCH TO ENSURE THAT ALL FASTENERS

ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

Hardware

DESCRIPTIONPART NUMBERQTYITEM

CARRIAGE BOLT1/2-13 x 1, GR8

CARRIAGE BOLT1/2-13 x 1 1/2, GR8

.250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP1243

1/2-13 x 4 x 7.25 x 1 3/4 SQ U-BOLTCM-1209-UBS44

HEX FLANGE NUTHFN 1213, GR820

HEX BOLTM10 - 1.5 x 40mm46

CONICAL TOOTHED WASHER7/16"

CARRIAGE BOLT5/8-11 x 1 1_2, GR8

.250 x 1.25 x 2.50" SQUARE HOLE SPACERCM-SP9

HEX FLANGE NUT5/8-11

410

HEX BOLT

M10 - 1.5 x 70mm411

1/2" PUSHNUT BOLT RETAINER1/2 PNBR212

Parts List

DESCRIPTIONPART NUMBERQTYITEM

2.50 x 2.00 x .375" CROSS ARM60660-CA

.250" DRIVER SIDE PLATE60660-DSWA

.250" DRIVER SIDE BRACKET60660-DSB1C

.250" PASSENGER SIDE PLATE60660-PSWA1D

.250" PASSENGER SIDE BRACKET60660-PSB1E

.313" SPACER PLATE60660-SP2F

EXHAUST HANGERCM-C655-EH1G

- LOWER SPARE TIRE

- NO MEASURING DRILL LOCATIONS

- NO DRILLING INTO FRAME

TOOLS REQUIRED

SAFETY GLASSES

RATCHET

15mm, 17mm, 3/4" & 15/16" SOCKETS

CRESCENT WRENCH

TORQUE WRENCH

PLATE POSITION FOR 4 x 4 MODELS

PLATE POSITION FOR 4 x 2 MODELS

DESIGNED FOR USE WITH

60612 CENTER SECTION

(NOT INCLUDED IN SUBKIT)

REPLACE STOCK RUBBER

ISOLATOR FOR ADDITIONAL

EXHAUST CLEARANCE

ON SOME MODELS

RUBBER

BUMP STOP

DRIVER SIDE

PLATE ASSEMBLY

PASSENGER

SIDE FRAME

RAIL

DRIVER SIDE

FRAME RAIL

IF SPACER

BLOCK IS

PRESENT

USE 70mm

HARDWARE

Summary of content (8 pages)

PAGE 1
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** DODGE 2500 / 3500 SHORT AND LONG BED 60660 SUBKIT 7/18/2014 PAGE 1 OF 5 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME MODELS MAY REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 2
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** DODGE 2500 / 3500 SHORT AND LONG BED 60660 SUBKIT PAGE 2 OF 5 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME MODELS MAY REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 3
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** DODGE 2500 / 3500 SHORT AND LONG BED 60660 SUBKIT PAGE 3 OF 5 BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME MODELS MAY REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 4
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60660 SUBKIT 3500 SHORT AND LONG BED PAGE 4 OF 5 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME MODELS MAY REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 5
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** CAB TO TRAILER CLEARANCE PAGE 5 OF 5 **REMOVAL OF REAR WINDOW ACCESSORIES MAY BE REQUIRED.** COUPLER OVERHANG TRAILER 4 in (W) 96 in COUPLER ***GENERALLY, TAPERED NOSE TRAILERS ADHERE TO THE FOLLOWING DESIGNS:*** 8 FT. WIDE TRAILERS TAPER TO 6 FT. AT THE COUPLER. 7 FT. WIDE TRAILERS TAPER TO 5 FT. AT THE COUPLER.
PAGE 6
INSTALLATION INSTRUCTIONS WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY DOUBLE LOCK GOOSENECK HITCH MAINTENANCE Keep gooseneck ball, cylinder and trailer coupler lubricated regularly. Use silicone spray or equivalent to prevent wear / rust. Keep hitch assembly and trailer coupler free of dirt and other foreign debris. Periodically check the gooseneck hitch to ensure that all fasteners are tight and that all structural components are sound.
PAGE 7
INSTALLATION Step 1 Using a 3/16" drill bit, drill a pilot hole from underneath the truck bed through the hole in center locator / trim shield (#2). See figure 2. Step 3 Using a 4" hole saw, drill the hole from above the truck bed. Take caution to not drill through the center locator / trim shield (#2) Note: The use of cutting fluid will ease this process. Remove the center locator by pulling it up through the hole. Step 4 Deburr the cut holes and spray exposed metal with rust inhibitor.
PAGE 8
BEFORE TOWING FOR THE FIRST TIME BEFORE TOWING EVERY TIME Verify adequate turning clearance between the truck cab / box corners and trailer. Ensure all fasteners are tight and that all structural components are sound. Note: Do not tow a trailer with worn or damaged parts. Check truck box clearance. There should be a minimum clearance of 6" between the bottom of the trailer overhang and the top of the box sides.