Owners manual

ManualsBrandsCurt ManualsAutomotiveCURT 60659 600 Series Install Kit Gooseneck Hitch

Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or

consequential loss or damage.

**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!**

C-659 SUBKIT

'02-'08 DODGE 1/2 TON TRUCKS

'03-PRESENT DODGE 3/4 & 1 TON TRUCKS

(WILL FIT 1/2, 3/4 & 1 TON MEGA CAB SHORT BED)

BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED

TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION

OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE

TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.

When placing the U-bolt against the frame stay under the wiring harness and brake line.

Make certain that nothing is between the U-bolt and frame before attaching to the side plate.

If needed, a brake line spacer is in the bolt kit and can be used to clamp the U-bolt over the

top of the brake line when installed as shown in Figure 4.

INSIDE DRIVER

SIDE FRAME

U-BOLT

BRAKE LINE

SPACER

DRIVER

SIDE PLATE

BRAKE LINE

(INSIDE OF

DRIVER SIDE

FRAME)

FIGURE 4

FRONT OF TRUCK

REAR OF TRUCK

WARNING!!

Summary of content (5 pages)

PAGE 1
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** '02-'08 DODGE 1/2 TON TRUCKS '03-PRESENT DODGE 3/4 & 1 TON TRUCKS C-659 SUBKIT (WILL FIT 1/2, 3/4 & 1 TON MEGA CAB SHORT BED) WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 2
C-659 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** '02-'08 DODGE 1/2 TON TRUCKS SUBKIT '03-PRESENT DODGE 3/4 & 1 TON TRUCKS (WILL FIT 1/2, 3/4 & 1 TON MEGA CAB SHORT BED) 7/13/2012 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 3
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** C-659 SUBKIT '02-'08 DODGE 1/2 TON TRUCKS '03-PRESENT DODGE 3/4 & 1 TON TRUCKS (WILL FIT 1/2, 3/4 & 1 TON MEGA CAB SHORT BED) Installation Steps Continued 3) Install the front cross arm by sliding it between the truck frame and truck bed above the passenger side rear tire. Slide through until both sides are resting on the truck frame.
PAGE 4
'02-'08 DODGE 1/2 TON TRUCKS '03-PRESENT DODGE 3/4 & 1 TON TRUCKS C-659 SUBKIT (WILL FIT 1/2, 3/4 & 1 TON MEGA CAB SHORT BED) REAR OF TRUCK Parts List ITEM QTY PART NUMBER 1 2 CM-1204-UBS DESCRIPTION 1/2-13 x 4 1/4 x 6 7/8 x 1 1/2 SQ U-BOLT 2 8 1/2 - 13 x 1 1/2 HEX BOLT 3 8 FW12 FW, 12, ZP 4 6 HFN 1213 HEX FLANGE NUT 5 4 1/2-13 x 1 1/2 CARRIAGE BOLT 6 1 5/16-18 x 1 CARRIAGE BOLT 7 1 5/16-18 HEX FLANGE NUT 8 10 1/2" LOCK WASHER 9 4 1_2 - 13 HEX NUT GR8 HEX NUT 10 2 5_8
PAGE 5
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** '02-'08 DODGE 1/2 TON TRUCKS '03-PRESENT DODGE 3/4 & 1 TON TRUCKS C-659 SUBKIT (WILL FIT 1/2, 3/4 & 1 TON MEGA CAB SHORT BED) **REMOVAL OF REAR WINDOW ACCESSORIES MAY BE REQUIRED.** COUPLER OVERHANG TRAILER 4 in (W) 96 in COUPLER ***GENERALLY, TAPERED NOSE TRAILERS ADHERE TO THE FOLLOWING DESIGNS:*** 8 FT. WIDE TRAILERS TAPER TO 6 FT. AT THE COUPLER. 7 FT. WIDE TRAILERS TAPER TO 5 FT. AT THE COUPLER.