Owners manual

ManualsBrandsCurt ManualsAutomotiveCURT 60647 Under-Bed Double Lock Gooseneck Install Kit

Hardware

DESCRIPTION

PART NUMBER

QTY

ITEM

HEX FLANGE NUT5/8-1141

.375 x 1.25 x 2.50" SQUARE HOLE SPACERCM-SP942

CARRIAGE BOLT5/8-11 x 1 3_4, GR8

HEX FLANGE NUTHFN 1213, GR8

124

HEX FLANGE NUT3_4 - 10 HFN, GR82

1/2-13 x 4 x 7.25 x 1 3/4 SQ U-BOLTCM-1209-UBS26

CARRIAGE BOLT1/2-13 x 1 1/2, GR8

CARRIAGE BOLT3_4 - 10 x 2.5, GR828

1/2" PUSHNUT BOLT RETAINER1/2 PNBR29

.375 x 1.38 x 2.50" CARRIAGE SPACER60647-CBS

210

PARTS LIST

DESCRIPTION

PART NUMBER

QTY

ITEM

2.00 x 2.00 x .375" CROSS ARM60647-CA

WELDMENT ASSEMBLY60647-DSWA1B

WELDMENT ASSEMBLY60647-PSWA1C

Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or

consequential loss or damage.

FORD F-250, F-350

11/5/2018

**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!**

60647 SUBKIT

PAGE 1 OF 4

WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME

MODELS MAY REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE

BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB. ON TWO WHEEL DRIVE TRUCKS A CLEARANCE CHECK MUST BE PERFORMED

WHEN TRUCK IS LOADED AND UNLOADED TO VERIFY THE INVERTED BALL WILL NOT INTERFERE WITH THE TOP OF THE DIFFERENTIAL

SUBKIT WEIGHT: LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

PERIODICALLY CHECK THIS GOOSENECK HITCH TO ENSURE THAT ALL FASTENERS

ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

FIGURE A

- NO MEASURING DRILL LOCATIONS

- NO DRILLING INTO FRAME

- NO LOWERING EXHAUST

- REMOVE HEAT SHEILD

BED

DRIVER SIDE

FRAME RAIL

REAR DRIVER SIDE TIRE

FRONT OF VEHICLE REAR OF VEHICLE

DESIGNED FOR USE WITH

60612 CENTER SECTION

(NOT INCLUDED IN SUBKIT)

DRIVER SIDE

FRAME RAIL

PASSENGER

SIDE FRAME

RAIL

1 ADDED "HELPING HAND" WASHERS 7/31/2014 KWS

2 REPLACED 5/8-11 X 1 1/2" CARRIAGE BOLT WITH 5/8-11 X 1 3/4 CARRIAGE BOLT 11/5/18 AGC

REVISION HISTORY

REV DESCRIPTION DATE APPROVED

Summary of content (4 pages)

PAGE 1
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350 60647 SUBKIT 11/5/2018 PAGE 1 OF 4 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME MODELS MAY REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 2
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350 60647 SUBKIT 11/5/2018 PAGE 2 OF 4 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. SOME MODELS MAY REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 3
**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** 60647 SUBKIT PAGE 3 OF 4 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ALL MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
PAGE 4
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** CAB TO TRAILER CLEARANCE PAGE 4 OF 4 **REMOVAL OF REAR WINDOW ACCESSORIES MAY BE REQUIRED.** COUPLER OVERHANG TRAILER 4 in (W) 96 in COUPLER ***GENERALLY, TAPERED NOSE TRAILERS ADHERE TO THE FOLLOWING DESIGNS:*** 8 FT. WIDE TRAILERS TAPER TO 6 FT. AT THE COUPLER. 7 FT. WIDE TRAILERS TAPER TO 5 FT. AT THE COUPLER.