Installation Guide

INSTALLED HITCH
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANU
FACTURER'S RECOMMENDED TOWING CAPACITY.***
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY):
MINUTES
INSTALL NOTES:
30,000 7,500
51
45
RAM 3500
3/31/2021
60626
90
WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE
FOR NEW HARDWARE. SOME MODELS REQUIRE MODIFICATION OR REMOVAL OF HEAT SHIELDS. ON SHORT BED MODELS,
CHECK FOR ADEQUATE TURNING CLEARANCE BETWEEN THE FRONT OF ALL TRAILERS AND THE TRUCK CAB.
- LOWER SPARE TIRE
- LOWER EXHAUST
- NO MEASURING DRILL LOCATIONS
- NO DRILLING INTO FRAME
PAGE 1 OF 4
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Scan
for more
information
Hardware List
DESCRIPTION
PART NUMBER
QTY
ITEM
FB,PATCH,5/8-11 UNC,1-1/2,GRD8,YZ10-1055361
NUT,CTR LOCK,5/8-18 UNF,GRDA,ZP
20-0013542
5/8" SQUARE U-BOLT
60614-UB23
U-BOLT SPRINGCM-C113-UBS
44
WASHER,FLAT,M16,YZ
30-0018585
Parts List
DESCRIPTIONPART NUMBERQTYITEM
GOOSENECK CENTER SECTION
60626-WA1A
DS NUT PLATE WELDMENT60626-DSNP
1B
PS NUT PLATE WELDMENT60626-PSNP
1
C
RUBBER COVER661551D
60601 GOOSENECK BALL606011E
CENTER LOCATOR / TRIM SHIELD60614-CL1F
1
A
DRIVER SIDE
FRAME RAIL
TRUCK BED
PASSENGER SIDE
FRAME RAIL
FACTORY CROSS MEMBER
REAR BED SUPPORT
FRONT BED
SUPPORT
B
E
C
D
TOOLS REQUIRED
TORQUE WRENCH
RATCHET
15/16" SOCKET
EXTENSION
DRILL
3-1/4" HOLE SAW
3/16" & 11/16" DRILL BIT
PRY BAR
CUTTING FLUID
RUST INHIBITOR
EAR PROTECTION
SAFETY GLASSES
NOTE: REVIEW 60601 INSTRUCTION
SHEET PRIOR TO USE.
NOTE: INSERT SUPPLIED RUBBER
COVER WHEN NOT IN USE
TRUCK BED
(TRIMMED FOR CLARITY)
DRIVER SIDE
FRAME RAIL
FACTORY CROSS MEMBER
REAR BED SUPPORT
5
4
3
2
NOTE: REQUIRES DRILLING
THROUGH THE FACTORY
CROSSMEMBER (4) PLACES
FOR SAFETY CHAIN LOOPS
INSTALL CENTER LOCATOR
INTO CYLINDER PRIOR
TO
RAISING GOOSENECK CENTER
SECTION INTO POSITION
F