Installation Guide

Parts List
DESCRIPTIONPART NUMBERQTYITEM
BOLT,CAR,7/16-14 UNC,1-1/2,GRD8,YZ10-1028221
HHCS,1/2-13 UNC,2,GRD8,YZ10-1028612
BOLT,CAR,3/8-16 UNC,1-1/4,GRD8,YZ
10-1042313
NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ
20-0006214
NUT,SER-FLANGE,3/8-16 UNC,GRD8,YZ20-0010225
NUT,SER-FLANGE,7/16-14 UNC,GRD8,YZ20-0010316
.250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP727
.250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP1818
.188 x 1.50 x 3.00" ROUND HOLE SPACERCM-SP3419
7/16" FISHWIRE7_16 FISHWIRE110
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): 125 MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
2000
200
26
60
11415
11/25/2020
1) Remove (2) fascia nuts from the under body panel and lower panel from vehicle. (Nuts will be reinstalled
in step 8)
2) Trim under body panel as shown in plastic under body panel cutout diagram.
3) Fishwire 7/16" carriage bolt and spacer in through the access hole and out the mounting hole in the
passenger side frame rail. Leave fishwire attached. (See fishwire technique diagram)
4) Raise hitch into position over fishwired bolt, remove fishwire and secure with flange nut.
5) Use 3/8" and 7/16" carriage bolts, spacers and flange nuts to secure the center of the hitch to the bumper
beam tab as shown.
6) Secure driver side arm to top of tow loop using 1/2" bolt, spacer, and flange nut as shown.
7) Torque all 1/2" fasteners to 110 lb-ft, all 7/16" fasteners to 70 lb-ft, and all 3/8" fasteners to 45 lb-ft.
8) Reinstall the fascia nuts. (Nuts that were removed in step 1)
6.250 in
4.500 in
5.875 in
4.313 in
PLASTIC UNDER BODY PANEL
CUTOUT DIAGRAM
- NO DRILLING REQUIRED
- LOWER AND TRIM FASCIA
DRIVER SIDE
PASSENGER SIDE
REAR OF VEHICLE
SAAB 9-3 SPORT COMBI WAGON
(ALL EXCEPT DUAL EXHAUST MODELS)
5
5
7
8
3
1
6
7
1
BUMPER
BEAM TAB
PASSENGER SIDE
FRAME RAIL
ACCESS HOLE
TOOLS REQUIRED
10mm, 3/8", 7/16", 1/2" SOCKETS
RATCHET
TORQUE WRENCH
2
9
4
DESIGNED FOR USE WITH
BALLMOUNT #55001 / 45501
10