Owners manual

ManualsBrandsCurt ManualsAutomotiveCURT 16422 Fifth Wheel Custom Bracket Kit Fits 09-10 Ram 1500

3/22/2013

16422

2009-2010 DODGE RAM 1500 (EXCLUDING CREW CAB 5' 7" BOX)

*** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMENDED TOWING CAPACITY ***

Page 1 of 3

HITCH WEIGHT: LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

180

Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or

consequential loss or damage.

Parts List

DESCRIPTION

PART NUMBER

QTY

ITEM

HANDLE NUT1/2-13101

HEX FLANGE NUTHFN 121392

HEX BOLT1/2-13 x 2"

103

.313" x 1.00 x 2.00" U-SHAPE SPACERCM-SP136

.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP6

.250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP1276

CARRIAGE BOLT1/2-13 x 1 3/4

1/2" FISHWIRE1_2 FISHWIRE28

1/2-13 x 4 1/8 x 7 x 1 1/2 SQ U-BOLTCM-1211-UBS19

TOOLS REQUIRED

3/4" AND 7/8" WRENCHES

1/8" AND 9/16" DRILL BITS

3/4" AND 7/8" SOCKETS

RATCHET

TORQUE WRENCH

DRILL

CENTER PUNCH

TAPE MEASURE

5TH WHEEL RAIL

(SOLD SEPARATELY)

PASSENGER

SIDE FRAME RAIL

DRIVER SIDE

FRAME RAIL

- DRILLING REQUIRED

- FISHWIRE HARDWARE

- LOWER SPARE TIRE

DRILL HOLE

Summary of content (3 pages)

PAGE 1
2009-2010 DODGE RAM 1500 (EXCLUDING CREW CAB 5' 7" BOX) 16422 Page 1 of 3 3/22/2013 *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMENDED TOWING CAPACITY *** ITEM 1 QTY 10 TOOLS REQUIRED 3/4" AND 7/8" WRENCHES 1/8" AND 9/16" DRILL BITS 3/4" AND 7/8" SOCKETS RATCHET TORQUE WRENCH DRILL CENTER PUNCH TAPE MEASURE Parts List PART NUMBER DESCRIPTION 1/2-13 HANDLE NUT 2 9 HFN 1213 HEX FLANGE NUT 3 10 1/2-13 x 2" HEX BOLT 4 8 CM-SP136 .313" x 1.00 x 2.00" U-SHAPE SPACER 5 4 CM-SP6 .250 x 1.
PAGE 2
16422 2009-2010 DODGE RAM 1500 2/11/2013 Page 2 of 3 WARNING: - Do not install mounting rails over plastic bed liners. Plastic liners must be trimmed for metal to metal contact. (Mounting rails may be installed on spray on liner.) - Use only supplied fasteners for installation. - Before installing mounting rails and hitch, measure to be sure there will be enough clearance between the truck and trailer to allow for turns. 1.
PAGE 3
16422 2009-2010 DODGE RAM 1500 Page 3 of 3 2/11/2013 DRILL (2) CENTER HOLES SHOWN IN ADDITION TO (8) HOLES FOR MOUNTING PLATES AND OTHER HARDWARE. INSTALL 1/2" BOLTS AND U-SHAPED SPACERS ABOVE OR BELOW BED TO FILL BED CORRUGATIONS AND BOLT PLATE BELOW BED WITH WASHERS AND NUTS. Front of Vehicle 29" SHORT BOX 31" LONG BOX REAR EDGE OF TRUCK BED BED (NOT TAILGATE) KING PIN CENTER APPROX.