Installation Guide

ManualsBrandsCURT ManualsAutomotiveCustom 5th Wheel Brackets, Select Ram 1500

Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or

consequential loss or damage.

7/2/2019

16307

RAM 1500

*** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMENDED TOWING CAPACITY ***

1 OF 3

180

HITCH WEIGHT:

LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

- LOWER SPARE TIRE

- NO FRAME DRILLING REQUIRED

Hardware List

DESCRIPTIONPART NUMBERQTYITEM

.313 x 1.25 x 2.00" 9/16" SQUARE HOLE SPACERCM-SP73

NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ20-00062182

HANDLE NUT1/2-1343

1/2" x 30" FISHWIRE1_2 x 30 FISHWIRE64

.250 x 1.00 x 2.50" SQUARE HOLE SPACERCM-SP106

BOLT, CAR,1/2-13 UNC,1-1/2,GRD8,YZ10-1028766

1/2-13 x 4 1/4 x 6 1/8 x 1 1/2 SQ U-BOLTCM-1205-UBS

.313" x 1.00 x 2.00" U-SHAPE SPACERCM-SP136

108

HHCS,1/2-13 UNC,2,GRD8

10-1028649

BOLT, CAR,1/2-13 UNC,2,GRD8,YZ

10-10288810

DRIVER SIDE FRONT PLATE16307-DSF111

DRIVER SIDE REAR PLATE16307-DSR112

PASSENGER SIDE FRONT PLATE16307-PSF113

PASSENGER SIDE REAR PLATE16307-PSR114

TOOLS REQUIRED

RATCHET

3/4" SOCKET

TORQUE WRENCH

CENTER PUNCH

DRILL

1/8" & 9/16" DRILL BITS

TAPE MEASURE

GRINDER

MOUNTING RAILS

SOLD SEPARATELY

TRUCK BED

PASSENGER SIDE FRAME RAIL

DRIVER SIDE

FRAME RAIL

BED SUPPORT RAIL

USE HANDLE NUT AND HEX HEAD BOLT

ON AIR RIDE EQUIPPED MODELS

(BOTH SIDES)

INSERT BOLT INTO

SPACER AND REVERSE

FISHWIRE INTO

FRAME RAIL PRIOR

TO INSTALLING SIDE

PLATE (BOTH SIDES)

INSTALL FASTENER IN

THIS LOCATION FOR

COIL SPRINGS

INSTALL FASTENER IN

THIS LOCATION FOR

AIR SUSPENSION

ACCESS HOLE

(BOTH SIDES)

Summary of content (3 pages)

PAGE 1
RAM 1500 16307 7/2/2019 1 OF 3 *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMENDED TOWING CAPACITY *** Hardware List ITEM QTY PART NUMBER 1 2 CM-SP73 TOOLS REQUIRED RATCHET 3/4" SOCKET TORQUE WRENCH CENTER PUNCH DRILL 1/8" & 9/16" DRILL BITS TAPE MEASURE GRINDER DESCRIPTION .313 x 1.25 x 2.00" 9/16" SQUARE HOLE SPACER 2 18 20-00062 NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ 3 4 1/2-13 HANDLE NUT 4 6 1_2 x 30 FISHWIRE 1/2" x 30" FISHWIRE 5 6 CM-SP10 .250 x 1.00 x 2.
PAGE 2
16307 RAM 1500 2 OF 3 WARNING: - Do not install mounting rails over plastic bed liners. Plastic liners must be trimmed for metal to metal contact. (Mounting rails may be installed on spray on liner.) - Use only supplied fasteners for installation. - Before installing mounting rails and hitch, measure to be sure there will be enough clearance between the truck and trailer to allow for turns. BEFORE INSTALLATION: Lower spare tire and remove heat shield as needed for access to the bottom of the truck bed.
PAGE 3
RAM 1500 16307 3 OF 3 WARNING: - Do not install mounting rails over plastic bed liners. Plastic liners must be trimmed for metal to metal contact. (Mounting rails may be installed on spray on liner.) - Use only supplied fasteners for installation. - Before installing mounting rails and hitch, measure to be sure there will be enough clearance between the truck and trailer to allow for turns.