Installation Guide

ManualsBrandsCURT ManualsOtherClass 3 Trailer Hitch, 2" Receiver, Select Toyota Sienna (Concealed Main Body), Towing Draw Bar

MAKE: STYLE:

WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY

For more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com

WEIGHT CARRYING:

INSTALLATION TIPS:

INSTALLATION REQUIRES:

VEHICLE PHOTO:

HITCH ILLUSTRATION:

REPRESENTATIVE PHOTO

MAKE SURE YOUR HITCH MATCHES

LEVEL OF DIFFICULTY: MODERATE

MODERATE CHALLENGING

1. BEFORE YOU BEGIN INSTALLATION, READ ALL

INSTRUCTIONS THOROUGHLY.

2. TO EASE INSTALLATION, 2 PEOPLE MAY BE

REQUIRED.

3. USING PROPER TOOLS WILL GREATLY IMPROVE

THE QUALITY OF THE INSTALL AND REDUCE THE

TIME REQUIRED.

4. NEED HELP OR HAVE SOME QUESTIONS?

CALL TECHNICAL SUPPORT AT 877.287.8634

Safety glasses should be

worn at all times while

installing this product.

YEARS: 2011-PRESENT TOYOTA MODEL: SIENNA VAN

3,500

525

TRAILER WEIGHT:

TONGUE WEIGHT:

13343 INSTALLATION INSTRUCTIONS

LBS.

120MIN.

MIN. PRO INSTALL TIME:

NOVICE INSTALL TIME:

IF YOU ARE HESITANT TO UNDERTAKE

THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED

CURT INSTALLER FOR ADDITIONAL ASSISTANCE.

SCAN FOR

MORE INFO

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND

CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product

voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.

For more information log onto www.curtmfg.com

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.

5/19/2020

EASY

RATCHET

SCREW

DRIVER

SOCKET

EXTENSION

SOCKET

19mm

10mm

TORQUE

WRENCH

MARKER

MASKING

TAPE

SAFETY

GLASSES

ROTARY TOOL

TAPE

MEASURE

NO DRILLING REQUIRED

LOWER EXHAUST

PART REMOVAL

TEMPORARILY REMOVE UNDERBODY

PANEL AND REAR FASCIA

TRIM UNDERBODY PANEL

A UPDATED HARDWARE DESCRIPTION 4/23/2020 CJW

B UPDATED PHONE NUMBER 5/19/2020 CJW

REVISION HISTORY

REV DESCRIPTION DATE APPROVED

Summary of content (8 pages)

PAGE 1
3343 YEARS: 2011-PRESENT Safety glasses should be worn at all times while installing this product . INSTALLATION INSTRUCTIONS MAKE: TOYOTA MODEL: SIENNA STYLE: VAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY For more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com WEIGHT CARRYING: PRO INSTALL TIME: NOVICE INSTALL TIME: TRAILER WEIGHT: TONGUE WEIGHT: 60 MIN. 120 MIN.
PAGE 2
INSTALLATION WALKTHROUGH: 1. Remove underbody panel, if present by removing (5) screws with a 10 mm socket, 4 plastic screws with a philips head screwdriver and 8 plastic push pins with a flat head screwdriver. Parts List ITEM QTY PART NUMBER DESCRIPTION 1 6 10-10277 HHCS,M12x1.25,40,CL10.9,YZ 2 6 30-00149 WASHER,S-CON,1/2,YZ PASSENGER SIDE FRAME RAIL 2 1 DRIVER SIDE FRAME RAIL EXISTING WELDNUTS (BOTH SIDES) For more information log onto www.curtmfg.com 2.
PAGE 3
INSTALLATION WALKTHROUGH: 3. Remove (1) plugs and (2) pieces of tape covering exisiting weldnuts on each side of vehicle. (See Weldnut Cleaning diagram) 5. Remove (1) screw per each side of vehicle inside of rear wheel well that are attaching the rear fascia to the vehicle side panels. 4. Open rear hatch of vehicle and remove (1) plastic rivet and (2) screws per each side of vehicle that are attaching the rear fascia. 6.
PAGE 4
INSTALLATION WALKTHROUGH: 7. Pull rear wheel well panel (both sides) away from rear fascia by unclipping the tab. Disconnect backup sensor connectors as needed. Gently remove fascia from vehicle and set aside. 8. Raise hitch into position and install M12 bolts and 1/2" conical toothed washers as shown. 9. Raise exhaust back into position. Reinstall rear fascia in reverse order of removal from Steps 4-7. 10. Mark underbody panel for trimming as shown below. Torque M12 hardware to 86 lb-ft.
PAGE 5
INSTALLATION WALKTHROUGH: 11. Trim underbody panel and reinstall in reverse order from Step 1. For more information log onto www.curtmfg.
PAGE 6
PAGE 7
13343 TOYOTA SIENNA PAGE 1 of 2 5/19/2020 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 3,500 LBS. TRAILER WEIGHT & 525 LBS. TONGUE WEIGHT. WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS. WARNING: ** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY ** WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY *** FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.
PAGE 8
13343 TOYOTA SIENNA 4/23/2020 PAGE 2 of 2 HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 877-287-8634 4 in 7 in UNDERBODY PANEL TRIM DIAGRAM INSTALLATION STEPS 1. Remove underbody panel, if present by removing (5) screws with a 10 mm socket, 4 plastic screws with a philips head screwdriver and 8 plastic push pins with a flat head screwdriver. 2. Lower exhaust by disconnecting (1) rubber isolator. (See Rubber Isolator Removal Diagram) 3.