Installation Guide

ManualsBrandsCURT ManualsOtherClass 1 Trailer Hitch, 1-1/4" Receiver, Select Honda Accord, Towing Draw Bar

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.

***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***

WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.

** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**

HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634

HITCH WEIGHT: LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS

ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or

consequential loss or damage.

2,000 200

HONDA ACCORD (ALL)

5/7/2020

11681

Parts List

DESCRIPTION

PART NUMBER

QTY

ITEM

BOLT,CAR,7/16-14 UNC,1-1/4,GRD8,YZ10-1028121

.250 x .88 x 2.25" SQUARE HOLE SPACERCM-SP222

NUT,SER-FLANGE,7/16-14 UNC,GRD8,YZ20-0010323

U-BOLT3_8 - 16 x 1.00 x 1.881

NUT,SER-FLANGE,3/8-16 UNC,GRD8,YZ

20-0010225

7/16" FISHWIRE7_16 FISHWIRE

PASSENGER SIDE

FRAME RAIL

DRIVER SIDE

FRAME RAIL

ACCESS HOLE

(BOTH SIDES)

DESIGNED FOR USE WITH

BALL MOUNT # D-55001 / 45501

- NO DRILLING REQUIRED

- HEAT SHIELD TRIMMING REQUIRED

- FISHWIRE HARDWARE

TOW LOOP

TRUNK PAN

EURO MOUNT OPTION AVAILABLE

#45571 (1-7/8" BALL) AND #45572 (2" BALL)

TOOLS REQUIRED

PRY BAR

RATCHET

10mm, 9/16" & 11/16" SOCKETS

TORQUE WRENCH

AVIATION SHEARS

TAPE MEASURE

SAFETY GLASSES

Summary of content (6 pages)

PAGE 1
1681 HONDA ACCORD (ALL) 5/7/2020 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 2,000 LBS. TRAILER WEIGHT & 200 LBS. TONGUE WEIGHT. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
PAGE 2
11681 HONDA ACCORD (ALL) GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 2,000 LBS. TRAILER WEIGHT & 200 LBS. TONGUE WEIGHT. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY AUXILIARY STABILIZING STRAPS.
PAGE 3
11681 YEARS: 2013 Safety glasses should be worn at all times while installing this product . INSTALLATION INSTRUCTIONS MAKE: HONDA MODEL: ACCORD STYLE: ALL WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY WEIGHT CARRYING: TRAILER WEIGHT: TONGUE WEIGHT: PRO: 30 MIN. INSTALLATION TIME: NOVICE: 60 MIN. THE INSTALL TIME LISTED IS FOR PROFESSIONAL INSTALLERS.
PAGE 4
INSTALLATION WALKTHROUGH: Parts List ITEM QTY PART NUMBER DESCRIPTION 1 2 10-10281 BOLT,CAR,7/16-14 UNC,1-1/4,GRD8,YZ 2 2 CM-SP2 .250 x .88 x 2.25" SQUARE HOLE SPACER 3 2 20-00103 NUT,SER-FLANGE,7/16-14 UNC,GRD8,YZ 4 1 3_8 - 16 x 1.00 x 1.
PAGE 5
INSTALLATION WALKTHROUGH: 1. Lower exhaust by removing two rubber exhaust isolators for single exhaust vehicles and three isolators for dual exhaust vehicles. See RUBBER ISOLATOR REMOVAL DIAGRAM below. 3. Fishwire 7/16"-14 x 1 1/4" carriage bolts with CM-SP2 spacers into poistion through access holes in both frame rails, as shown on page 1. See FISHWIRE TECHNIQUE DIAGRAM below. NOTE: Leave fishwires attached to prevent loss of hardware inside of frame rail. 2.
PAGE 6
INSTALLATION WALKTHROUGH: 5. Insert fishwires through mounting holes in hitch and raise hitch into position. Secure it to the U-bolt with 3/8"-16 hex flange nuts. Remove fishwires and attach 7/16"-14 hex flange nuts to the carriage bolts. 7. Trim heat shield(s) around hitch. Reinstall heat shield(s) with hardware removed in Step 2. Bend heat sheild over hitch as needed. NOTE: One fastener per shield will not be reinstalled. See HEAT SHIELD TRIMMING DIAGRAM below.