Owners manual

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
WARNING: ** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY **
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM & FOR HELPFUL TOWING TIPS LOG ONTO WWW.HITCHINFO.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
2,000 200
25
35
SUBARU IMPREZA SEDAN
2/20/2017
11466
70
Scan
for more
information
Parts List
DESCRIPTIONPART NUMBERQTYITEM
CARRIAGE BOLT1/2-13 x 1 1/2
61
.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP6
62
HEX FLANGE NUT
HFN 121363
1/2" FISHWIRE1_2 FISHWIRE64
1) Lower exhaust by removing (3) rubber isolators. See RUBBER ISOLATOR REMOVAL DIAGRAM. If needed to access
outside hangers remove plastic underbody panel by removing (7) plastic fasteners. Note: Support exhaust as required.
2) Remove the heat shield by removing the (4) small screws with a 10mm socket. Cut (2) holes in the heat shield as shown
in the diagram above.
3) Remove (8) rubber plugs from frame (1 large and 3 small, from each frame rail). Enlarge the access hole on both sides
to allow the 1/2" fasteners to pass into the frame rail.
4) Reinstall heat shield with (3) of the fasteners, without using the fastener between the hitch mounting holes. Fishwire the
1/2" hardware through the access hole into position on both sides, as shown above.
5) Raise hitch into position and loosely install 1/2" hex flange nuts. Note: The heat shield will be between the hitch and
vehicle frame rails.
6) Torque all 1/2" fasteners to 110 lb-ft.
7) Reinstall the exhaust and underbody panels onto the vehicle.
- LOWER EXHAUST (5 HANGERS)
- FISHWIRING REQUIRED
- ENLARGE HOLE / TRIM HEAT SHIELD
TOOLS REQUIRED
3/4" SOCKET
10mm SOCKET
RATCHET
TORQUE WRENCH
DIE GRINDER
AVIATOR SHEARS
SAFETY GLASSES
TRIM 1" HOLE ON
DIMPLE ON "R↑" AND "M"
1
2
3
4
DRIVER SIDE
FRAME RAIL
ENLARGE ACCESS HOLE
(BOTH SIDES)
PASSENGER SIDE
FRAME RAIL
DESIGNED FOR USE WITH
BALLMOUNT #45521
EURO MOUNT OPTION AVAILABLE
#45571 (1 7/8" BALL) OR #45572 (2" BALL)