Owners manual

ManualsBrandsCurt ManualsAutomotiveCURT 111113 Class I 1.25 in. Receiver Hitch Fits 11-19 M37 Q70 Q70L

MAKE: STYLE:

MIN.

WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY

For more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com

WEIGHT CARRYING:

INSTALLATION TIPS:

INSTALLATION REQUIRES:

VEHICLE PHOTO:

HITCH ILLUSTRATION:

REPRESENTATIVE PHOTO

MAKE SURE YOUR HITCH MATCHES

LEVEL OF DIFFICULTY:

CHALLENGING

MODERATE CHALLENGING

1. BEFORE YOU BEGIN INSTALLATION, READ ALL

INSTRUCTIONS THOROUGHLY.

2. TO EASE INSTALLATION, 2 PEOPLE MAY BE

REQUIRED.

3. USING PROPER TOOLS WILL GREATLY IMPROVE

THE QUALITY OF THE INSTALL AND REDUCE THE

TIME REQUIRED.

4. NEED HELP OR HAVE SOME QUESTIONS?

CALL TECHNICAL SUPPORT AT 800.798.0813

Safety glasses should be

worn at all times while

installing this product

YEARS:

MODEL:

TRAILER WEIGHT:

TONGUE WEIGHT:

INSTALLATION INSTRUCTIONS

LBS.

WARNING:

ALL NON-TRAILER (WHEEL-LESS) LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED

BY 18050 STABILIZING STRAPS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT

WWW.CURTMFG.COM FOR FURTHER INFORMATION.

MIN.

IF YOU ARE HESITANT TO UNDERTAKE

THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED

CURT INSTALLER FOR ADDITIONAL ASSISTANCE.

NOVICE INSTALL TIME:

PRO INSTALL TIME:

SCAN FOR

MORE INFO

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND

CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product

voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.

For more information log onto www.curtmfg.com

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.

EASY

11111

2011-2013

INFINITI

M37X, M56X

SEDAN

2014-CURRENT

INFINITI

Q70

SEDAN

2,000

200

180

2/1/2018

PHILLIPS & FLAT

HEAD

SCREW DRIVER

SOCKET

10mm

12mm

RATCHET

TORQUE

WRENCH

ROTARY TOOL

MARKER

TRIM UNDERBODY PANEL

PART REMOVAL

REMOVE BUMPER

NO DRILLING REQUIRED

Summary of content (8 pages)

PAGE 1
1111 YEARS: 2011-2013 2014-CURRENT Safety glasses should be worn at all times while installing this product . INSTALLATION INSTRUCTIONS MODEL: M37X, M56X Q70 MAKE: INFINITI INFINITI STYLE: SEDAN SEDAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY For more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com WEIGHT CARRYING: PRO INSTALL TIME: NOVICE INSTALL TIME: TRAILER WEIGHT: TONGUE WEIGHT: 90 MIN. 180 MIN.
PAGE 2
INSTALLATION WALKTHROUGH: Parts List ITEM QTY PART NUMBER DESCRIPTION 1 12 M8-1.25 x 35 HEX BOLT 2 12 3/8" CONICAL TOOTHED WASHER 1. Remove underbody panel by removing (7) fasteners. Remove (1) push fastener which holds bumper cover to vehicle next to the tow loop. TRIM DIAGRAM  TRIM 41 4 in 41 2 in 37 8 in NOTE: TRIM DIMENSIONS ARE APPROXIMATE. CHECK FIT PRIOR TO COMPLETING TRIM. 2. Begin bumper cover removal process by removing (2) fasteners behind rear tire.
PAGE 3
INSTALLATION WALKTHROUGH: 3. Remove (2) push fasteners from wheel well liner and (2) fasteners from bottom of bumper cover. 5. Pull back piece of fascia which is glued to bumper cover directly behind rear tire and remove (1) hex fastener. Repeat STEPS 2-5 on other side of vehicle.   4. Pull back wheel well liner to remove (1) hex head fastener. For more information log onto www.curtmfg.com 6. Remove trunk floor board which conceals spare tire inside of trunk.
PAGE 4
INSTALLATION WALKTHROUGH: 7. Remove rearmost plastic cover inside of trunk by removing (4) loop fasteners and (2) push fasteners. 9. Pop off plastic covers attached to the inside of tail lights. 8. Pull back inner trunk liner to expose and remove (2) hex nuts. It may ease the process to remove push fasteners from inner liner. Repeat on other side. 10. Carefully pull off tail lights by pulling straight back. For more information log onto www.curtmfg.
PAGE 5
INSTALLATION WALKTHROUGH: 11. Remove (1) hex fastener and (2) push fasteners on each side which were hidden by tail lights. 13. Remove bumper beam by removing (6) M8 fasteners which hold bumper beam supports to trunk pan. Repeat on other each side and return (12) M8 fasteners to vehicle owner.    12. Carefully remove bumper cover. Pop sides off first and then pull straight back. Note: Remove foam insert and return to vehicle owner. For more information log onto www.curtmfg.com 14.
PAGE 6
INSTALLATION WALKTHROUGH: 15. Torque all M8 hardware to 23 ft-lbs. 16. Reinstall bumper cover and tail lights by reassembling components removed in STEPS 2-12 in reverse order. For more information log onto www.curtmfg.com 17. Trim underbody panel and reinstall. See TRIM DIAGRAM on PAGE 2. Install is complete.
PAGE 7
INFINITI M37X, M56X, Q70 11111 PAGE 1 of 2 2/1/2018 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 2,000 LBS. TRAILER WEIGHT & 200 LBS. TONGUE WEIGHT. WARNING: ALL NON-TRAILER (WHEEL-LESS) LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS. WARNING: ** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY ** WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY *** FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.
PAGE 8
11111 INFINITI M37X, M56X, Q70 2/1/2018 PAGE 2 of 2 HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813 INSTALLED POSITION INSTALLATION STEPS 1. Remove underbody panel by removing (7) fasteners. Remove (1) push fastener which holds bumper cover to vehicle next to the tow loop. 2. Begin bumper cover removal process by removing (2) fasteners behind rear tire. 3. Remove (2) push fasteners from wheel well liner and (2) fasteners from bottom of bumper cover. 4.