Product Manual

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM & FOR HELPFUL TOWING TIPS LOG ONTO WWW.HITCHINFO.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
5,000 500
32
20
RAM PROMASTER
11/4/2016
13295
40
Scan
for more
information
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
CARRIAGE BOLT1/2-13 x 1 1/421
HEX FLANGE NUTHFN 121322
.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP6
23
1/2" FISHWIRE1_2 FISHWIRE
24
M10-1.25 x 30 HEX FLANGE BOLT
M10 - 1.25 x 30 HFB45
1. Open the rear vehicle doors to expose the bumper cover and fasteners. Using a T30 torx bit, remove (8) fasteners and
the bumper cover. Note
: If present, disconnect the rear back-up sensor before completely removing the bumper cover.
2. Remove (2) M10 bolts and (1) M10 nut securing the bumper beam to the end of the frame, both sides.
Note
: Remove the M10 bolts with a 16mm socket and the M10 nuts using a 15mm socket.
3. Fishwire the 1/2" carriage bolts and SP6 spacers through the access holes and out the existing holes in the bumper beam.
4. With the hitch side plates flat on the ground, align the center holes of the hitch with the bolts fishwired in the bumper beam and
loosely secure with 1/2" flange nuts.
5. Raise the hitch and bumper beam into position by aligning the hitch and bumper beam holes with the holes in the end of the frame.
Secure with the M10-1.25 x 30mm hex flange bolts provided and the M10 nuts removed in Step (2).
6. Torque all 1/2" hardware to 110 ft-lbs.
Torque all 10mm hardware to 48 ft-lbs.
7. Reinstall bumper cover with fasteners removed in Step (1). Note: If present, reconnect the back-up sensor. You may need to
gently flex the cover to align with fastener holes.
BUMPER COVER
BUMPER COVER
FASTENER
ACCESS HOLE
(BOTH SIDES)
3
1
4
BUMPER BEAM
EXISTING M10 BOLTS
(BOTH SIDES)
EXISTING M10 NUT
(BOTH SIDES)
REAR OF VEHICLE
TOOLS REQUIRED
RATCHET
TORQUE WRENCH
15mm, 16mm, & 3/4" SOCKET
T30 TORX BIT
SAFETY GLASSES
5
- NO DRILLING
- FISHWIRE HARDWARE
- TEMPORARY PART REMOVAL
2