B U I L T -IN ELECTRIC HOB INSTRUCTION MANUAL CSPHOBW10 CSPHOBW10_IB_final110415.
CSPHOBW10_IB_final110415.
Contents Unpacking...................................................................................................................................... 4 Product Overview.......................................................................................................................... 5 Top View........................................................................................................................................................................5 Control Panel.........................
Thank you on the purchase of your new Currys Essentials Built-in Electric Hob. We recommend that you spend some time to read this manual in order to fully understand how to install and operate it correctly. Read all the safety warnings carefully before use and keep this manual for future reference. Unpacking Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to local regulations. The following items are included: Main Unit Screws × 4 P.N.: ST4.
Product Overview Top View 2 1 3 2 1. max.1000 W zone 2. max.1500 W zone 3. Control Panel 1 Control Panel 1 2 1. Power Indicator Light 2. Power Regulating Controls 5 CSPHOBW10_IB_final110415.
Before using your New Electric Hob • Read this guide, taking special note of the ‘Safety Warnings’ section. • Remove any protective film that may still be on your electric hob. Choosing the Right Cookware Do not use cookware with jagged edges or a curved base. Make sure that the base of your pan is smooth, sits flat against the surface, and is the same size as the cooking zone. Always centre your pan on the cooking zone.
Using Your Electric Hob To Start Cooking 1. Place a suitable pan on the cooking zone you wish to use. • 2. Make sure the bottom of the pan and the surface of the cooking zone are clean and dry. Adjust the power regulating control to the desired level to turn on the control. Setting 1 – Lower heat setting Setting 6 – Higher heat setting When You Have Finished Cooking Turn the cooking zone off by turning the power regulating control to “0“ position. 7 CSPHOBW10_IB_final110415.
Cooking Guidelines Take care when frying as oil and fat heat up very quickly. At extremely high temperatures oil and fat will ignite spontaneously and this presents a serious fire risk. Cooking Tips • When food comes to the boil, reduce the temperature setting. • Using a lid will reduce cooking times and save energy by retaining the heat. • Minimise the amount of liquid or fat to reduce cooking times. • Start cooking on a high setting and reduce the setting when the food has heated through.
Cleaning and Maintenance The settings below are guidelines only. The exact setting will depend on several factors, including your cookware and the amount you are cooking. Experiment with the electric hob to find the settings that best suit you. What? Everyday soiling on surface (fingerprints, marks, stains left by food or non-sugary spillovers on the surface) How? 1. Switch the power to the electric hob off. 2. Apply an electric hob cleaner while the electric hob is still warm (but not hot!) 3.
Specification Model CSPHOBW10 Power (W) 5000 – 5440W Voltage (V) 230 - 240 V~ Frequency (Hz) 50 Features and specifications are subject to change without prior notice. 10 CSPHOBW10_IB_final110415.
Installation Preparing the Worktop Cut out the work surface following the dimensions shown in the drawing below. For the purpose of installation and use, a minimum distance of 5cm space must be left around the cut out. Be sure the thickness of the work surface is at least 20mm. Use a heat-resistant work surface material to avoid deformation caused by the heat from the hob. The minimum distance between the hob and the cupboard should be at least 65cm.
Fastening the Fixing Brackets The unit should be placed on a stable, smooth surface (use the packaging). 1. Turn the hob upside down, place it on a soft surface and fasten the brackets to the appropriate holes. DO NOT tighten the screws at this stage. 2. Apply sealing strips around the edge of the hob. Screw Brackets Screw Screw Brackets Brackets Screw Brackets • • • • • The hob must be installed by qualified personnel or technicians.
Connecting the Hob to the Mains Power Supply The socket should be connected in compliance with the relevant standard,or a single-pole circuit breaker. The method of connection is shown below. L N L N 3 × 6mm2 / 3 × 2.5mm2 • This appliance must be earthed. • For this connection a power lead of wire type H05VV-F should be used. 1. If the cable is damaged or needs replacing, this should be done by an after-sales technician using the proper tools, so as to avoid any accidents. 2.
Safety Warnings Your safety is important to us. Please read this information before using your electric hob. Operation and Maintenance Installation Electrical Shock Hazard Electrical Shock Hazard • Disconnect the appliance from the mains electricity supply before carrying out any work or maintenance on it. • Connection to a good earth wiring system is essential and mandatory. • Alterations to the domestic wiring system must only be made by a qualified electrician.
Important Safety Instructions • Do not stand on your electric hob. • Never leave the appliance unattended when in use. Boilover causes smoking and greasy spillovers that may ignite. • Do not use pans with jagged edges or drag pans across the ceramic electric hob as this can scratch the surface. • Never use your appliance as a work or storage surface. • Do not use scourers or any other harsh abrasive cleaning agents to clean your electric hob, as these can scratch the surface.
If you require a replacement for any of the items listed below, please quote their corresponding part numbers: Replacement Part Part Number Screw ST4.2x22 Brackets SBD-55AM4AA.FJ-01 Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories. With over 1 million spares and accessories available we can deliver direct to your door the very next day. Visit www.partmaster.co.uk or call 0844 8003 456 (UK customers only) Calls charged at National Rate.
