Owner`s manual
8 9
www.CurrieTech.com
Currie Technologies
®
Currie Technologies
®
OM Direct Drive Scooters - 2012.indd
Modied 05/25/2012
Section 3 - BASIC ASSEMBLY & SET-UP
IMPORTANT: Some adult assembly required. Before using your scooter
please be sure to read and follow the basic assembly, set-up and operating
instructions. Following these instructions will help insure safe riding.
TOOLS REQUIRED:
Listed below are the tools you may need to assemble and adjust your
Electro-Drive™ scooter depending on model:
STEPS FOR BASIC ASSEMBLY
1. Remove scooter from carton. Remove all of the packaging materials
• 10mm box wrench
• 13mm box wrench
• 15mm box wrench
• 17mm cone wrench
• 4mm hex key wrench
• 5mm hex key wrench
• 6mm hex key wrench
• Phillips screwdriver
• Bicycle tire pump
from the scooter.
2. Install the front wheel (certain models will have the front wheel
already installed) being sure to properly install the safety washers.
Align the front wheel in the fork and tighten the axle nuts. Wait until
after you have installed the handlebars to connect the front brake (if
your scooter is so equipped).
3. Install the handlebars onto the stem, align and tighten.
4. Unfold the stem hinge. Be sure the locking pin is fully engaged and
close the quick release lever.
5. The brake(s) come pre-assembled from the factory (some scooters
have one brake while others have two brakes). However, you need
to check to make sure it is connected and operating properly. Test
the brake lever(s) by squeezing it. It should stop the
wheel(s) easily and NOT come in contact with the
handlebar. If the brake lever(s) needs adjusting, refer
to pages 19-20 for instructions. If the brake(s) does
not work properly, DO NOT RIDE THE SCOOTER.
Call Customer Service at 1-800-377-4532 for further
assistance.
6. Install the seat assembly, if so desired, by fully sliding the seat
tube into the frame and securing the pinch bolt. If the seat tube is
equipped with an indexing pin be sure to align this properly with the
frame.
7. Install the seat onto the seat tube if not already done and align
saddle angle and tilt and tighten accordingly.
8. Remove the battery charger from its box. Make sure the power
switch on the scooter is in the “OFF” position. Connect the charger
to the scooter first then plug the charger into the wall socket. Allow
the batteries to charge a full 6-10 hours (depending on the size of
batteries) before first use. Refer to page 17 for complete Battery
Care instructions
9. Before every ride, test the throttle with the power switch in
the “OFF” position. Twist the throttle, it should twist easily and
immediately spring back to the starting position when you release
it. If the throttle does not work properly, DO NOT RIDE THE
SCOOTER. Call Customer Service at 1-800-377-4532 for further
assistance.
10. Check tire pressure and inflate to the pressure marked on the tire
sidewall as necessary.
Before you ride the scooter, make sure you have tightened all parts. Riding
with a loose handlebar, front wheel, brake, seat assembly, etc. may cause a
rider to fall, possibly damaging the scooter and causing serious injury.
WARNING
!
STOPPING
1.
To slow down or come to a stop, allow the throttle to completely return to its
“zero speed” position
2. Squeeze the brake lever(s) on the handlebar to come to a safe stop. (Note: It
is not necessary to skid the wheel in order to slow or stop the scooter)
Skidding the wheel can damage the wheel and is not
covered by the warranty!
STORING YOUR SCOOTER
1. When you are not using the scooter, turn the power switch to the
“OFF” position.
2. Always be sure to fully charge batteries (6-10 hours depending on
battery size) at least every 30 days.
3. Plug the charger into the scooter then plug the charger into the wall
outlet. Do not charge your battery for more than 24 hours at one time.
5 MINUTE SLEEP MODE
Scooters are equipped with a 5 minute sleep mode. If no activity is detected
after 5 minutes the scooter will go into stasis mode to conserve the batteries.
To restart, cycle the power switch Off then On.
Never store your scooter in Sleep Mode as battery power will still be used by
the scooter. Always be sure to turn the power switch to the “OFF” position.
WARNING
!