DRAPERY TRACK Installation Manual and User Guide 1
Diagram TABLE OF CONTENTS List of Parts Wall Mount Drapery Track Installation and Connecting the Motors Ceiling Mount Drapery Track Installation and Connecting the Motors Install the Facia (Optional) Start Up Optional Programming Steps for the Track Drapery Change Positions on the Track Drapery (Single) Change Positions on the Track Drapery (Dual) Enable or Disable Smart Assist Pair the Remote Control Grouping Multiple Drapery Together Switch the Open and Close Positions Change the Frequency Swap the Open
the teps into iver wise ush sert Use h= mm). 1/2” ems, ww. Wall Mount DRapery Track Installation and connecting the motors For additional help during installation of your drapery track, visit www. currentproductscorp.com/support/drapery-track or call 1-844-307-7435. 1. Install the Brackets Carefully measure to the center of the window and make a small mark with a pencil.
B) If drilling into studs, no wall anchors are necessary. Carefully drill a pilot hole for all three screws. Use a 5/32” drill bit for the pilot holes if using the provided screws. Place the bracket against the wall, lining the holes in the bracket up with the holes in the wall. Screw in each screw until secure. Make sure your screw has solid embedment into the stud. Do not over torque. There should be no movement by the bracket after installation. Fig. X Fig.
2. Install the Track Starting in the middle, secure the track onto each of the brackets using each camlock. With the camlock arm open, or facing towards you, push the track upward so the camlock features rest in the groove on the top of the track. Turn the camlock arm to the left so the features inside the top track groove bite in and hold. Once all the camlocks are closed, use a screwdriver to tighten each camlock so the track is secure. Fig. X Fig.
For drapery with snaps, the carriers are connected with a cord. To remove carriers simply slide the desired number to be removed from the track and cut the string. To add carriers the whole string will need to be replaced. Slide the hardstop back into the track and tighten the screw. Fig. X 4. Connect the Motors On a single drapery, insert the motor shaft into the motor end of the drapery track and twist the motor into place. Push the locking tab up until it clicks into place.
6. Connect the Control Box (optional) On a single drapery, plug the motor into the Motor 1 slot. On a dual drapery, plug the room side drapery into the Motor 1 slot and window side drapery into the Motor 2 slot. 7. Attach the Drapery Snap or hook the drapery into each carrier, starting with the master carrier arm(s) and ending with the end(s) of the track. Wrap and pin the remaining fabric around the motor, hiding it from plain sight, but making sure the TAU is accessible. Fig. X Fig. X Fig.
Ceiling Mount DRapery Track Installation and connecting the motors For additional help during installation of your drapery track, visit www. currentproductscorp.com/support/drapery-track or call 1-844-307-7435. 1. Install the Camlocks The number of camlocks needed will depend on the desired length of the track. Mount a camlock every 16-32 inches along the ceiling. If installing a fascia, be sure to use the included small or large spacers. If not screwing into a joice, use the included anchors. Fig. X 2.
4. Adjust Number of Carriers It may be necessary to add or remove carriers based on curtain. To add or remove carriers, loosen the screw on the hardstop and slide it out of the track. Insert or remove carriers until the correct amount remain in the track. On a center draw, do this on each side. Slide the hardstop back into the track and tighten the screw. Fig. X Fig. X 5.
6. Connect the Control Box (optional) On a single drapery, plug the motor into the Motor 1 slot. On a dual drapery, plug the room side drapery into the Motor 1 slot and window side drapery into the Motor 2 slot. 7. Attach the Drapery Snap or hook the drapery into each carrier, starting with the master carrier arm(s) and ending with the end(s) of the track. Wrap and pin the remaining fabric around the motor, hiding it from plain sight, but making sure the pendant is accessible.
(Optional) Install the Facia 1. Install the Clips On ceiling mount installations the fascia clips will already be installed on the track drapery, so proceed to step 2. On wall mounted track installations, snap the fascia clips into the recess at the top of the drapery track, one side at a time. Use a fascia clip between each set of brackets. 2. Snap on the Fascia Orient the fascia so the protrusion is at the top.
Start up 1. Connect Power On battery powered units, untwist the TAU and insert (6) or (8) D Alkaline batteries, negative end first. Twist the TAU lock to secure back onto the unit. On rechargeable battery powered units, twist the TAU lock to secure onto the unit. On low voltage units, power up by plugging the unit into the desired outlet.
Optional Programming steps for the Drapery Track Change Positions on the drapery Track (Single) Change the open Position 1. Enter Learn Mode Pull down and release the TAU so the drapery moves towards the direction you would like to set as the “open” position. After the drapery reaches the position, it will stop moving. Pull down and hold the TAU for five seconds, or until the drapery jogs. Release the TAU. Fig. X Fig. X 2.
Change the Close Position 1. Enter Learn Mode Pull down and release the TAU so the drapery moves towards the direction you would like to set as the “close” position. After the drapery reaches the position, it will stop moving. Pull down and hold the TAU for five seconds, or until the drapery jogs. Release the TAU. Fig. X Fig. X 2. Set the Close Position By hand, pull the curtain until it reaches the desired full close position.
Change Positions on the drapery Track (dual) Change the open Position for the Room Side curtain (Motor 1) 1. Enter Learn Mode Pull down and release the TAU so the room side drapery moves towards the direction you would like to set as the “open” position. After the drapery reaches the position, it will stop moving. Pull down and hold the TAU for five seconds, or until the drapery jogs. Release the TAU. Fig. X Fig. X 2.
2. Set the Close Position By hand, pull the curtain until it reaches the desired full close position. Fig. X 3. Exit Mode Pull down on the TAU once to exit learn mode. The drapery will jog to confirm it has learned this position. Fig. X Change the open Position for the window side curtain (Motor 2) 1. Enter Learn Mode Lift up and release the TAU so the drapery moves towards the direction you would like to set as the “open” position. After the drapery reaches the position, it will stop moving.
Change the Close Position for the window side curtain 1. Enter Learn Mode Lift up and release the TAU so the drapery moves towards the direction you would like to set as the “close” position. After the drapery reaches the position, it will stop moving. Push up and hold the TAU for five seconds, or until the drapery jogs. Release the TAU. Fig. X Fig. X 2. Set the Close Position By hand, pull the curtain until it reaches the desired full close position. Fig. X 3.
Enable or disable smart assist Smart Assist allows users to pull the curtain manually and have the movement complete automatically. All drapery tracks come with Smart Assist enabled. 1. Move the Drapery Manually Begin with the curtain in the full open or full closed position. Manually move the drapery more than a foot towards the opposite direction. If Smart Assist is enabled, the drapery will begin to complete the movement automatically. If Smart Assist is disabled, the curtain will remain in place.
Pair the Remote to the drapery (FM) 1. Initiate Learn Mode Pull down and release the TAU twice to enter learn mode. After the first tug, the drapery should start moving. The second tug should stop it. 2. Connect the Remote On multi-channel remotes, select the channel you wish to pair to by pressing the Channel button until the LED corresponding with the appropriate channel is lit.
Pair the Remote to the drapery (Zigbee) 1. Connect Remote to Bridge If using the Current Products Corp. bridge, use a tack or other object to depress and release the recessed button on the bottom of the bridge to put the bridge into pairing mode. The LED should flash blue to show it is in pairing mode. Pull the “Pull” tab from the bottom of the remote. If the tab has already been pulled, push any button on the face of the remote. The LEDs should scroll to show it is seeking a bridge. 2.
Grouping Multiple Drapery Together The grouping feature is available on all units with a control box. Grouping allows users to control multiple units simultaneously with one manual command. Grouping also allows units to move together simultaneously when any one unit in the group has a sensor automated command triggered. 1. Enter Pairing Mode On each drapery you would like to group, pull down on the Pendant twice. After the first pull, the drapery should move. The second pull should stop it. 2x Fig.
Change the Frequency (FLOW with bridge ONLY) In rare instances it may become necessary to alter the frequency on which the device communicates. The frequency will need to be changed on both the unit and the remote. To do this, you must have the bridge and the multichannel remote. ? In most instances, when the frequency of the device needs to be changed, the user will recieve an alert through the Smart Phone app. 1.
The LEDs will change to reflect the current frequency (Fig. X). Stop when you determine the frequency matches the frequency from the bridge. Frequency Number LED Pattern 1 434.625 2 434.825 3 435.025 4 435.225 5 435.425 6 435.625 7 435.825 8 436.025 Fig. X 4. Exit Frequency Change Mode When you reach the desired frequency, exit the mode by pressing and releasing one of the two lower remote buttons. 25 Frequency Fig.
Swap the Open and Close Directions on a single drapery In some cases, to maximize functionality, users may want to swap which button on the remote control opens and closes the drapery. 1. Swap Directions First, depress a tack or pin into hole in the back of the remote to press and release the recessed button twice. The LEDs on the front of the remote should blink to confirm you are in the correct mode. To swap the open and close directions, press and release the top left button. 2.
2. Swap Directions for Motor 2 To swap the open and close directions for motor 2, press and release the bottom left button. 3. Confirm On the drapery you wish to swap the open and close direction of, pull down and release the TAU once. The drapery will jog to confirm it has switched open and close directions. Fig. X Fig. X Switch motor response Controls for a dual drapery In some cases, to maximize functionality, users may want to swap the control functions for the window side and room side curtains.
Master Reset the Drapery In some instances it may become necessary to master reset your drapery. Performing a master reset will restore the drapery to its factory settings, erasing saved open and closed positions, groups, and all paired remotes. 1. Remove Power Disconnect power from the unit. For hardwired units, simply unplug the device. For battery powered units, remove the battery tube by twisting it off of the connection wire. With power disonnected, pull down on the Pendant or cord and release once.
Connect & Integrate the drapery Track Pair or Unpair A Remote Control 1. Initiate Learn Mode 2x Pull down and release the TAU twice to enter learn mode. After the first tug, the drapery should start moving. The second tug should stop it. Fig. X 2. Connect the Remote If the remote is multi-channel, select the channel you wish to pair to by pressing the Channel button until the LED corresponding with the appropriate channel is lit. Fig.
Setup with the bridge and app 1. Download the App Download the Current Products Corp. app from the Google Play Store or the App Store. Follow the prompts to set up your account. 2. Connect Power to Bridge Find an outlet in a location central to the drapery you are installing in the home. Insert the micro-usb end of the included power cable into the power port on the bridge. Plug the other end of the cable into an outlet. Fig. X Fig. X 3.
Setup with the bridge (No App) 1. Connect Power to Bridge Find an outlet in a location central to the drapery you are installing in the home. Insert the micro-usb end of the included power cable into the power port on the bridge. Plug the other end of the cable into an outlet. Fig. X 2. Put Bridge into Pairing Mode Push a tack or pen into the hole in the back of the bridge to depress and release the recessed button. The blue LED should illuminate. 3.
Integrate with Amazon Echo - 434 FM 1. Set up your Echo If your Alexa device is not yet set up, do so now by following the instructions that came with your device. Also be sure the bridge has been setup. For instructions on how to set up your bridge and app, go to page ____. Fig. X 2. Download the Skill Use the “add a skill” (+) button inside your Alexa App. Search for the skill titled “My Curtains” or “Current Products”.
Integrate with Amazon Echo Plus- ZigBee with Current Products corp bridge 1. Set up your Echo If your Alexa device is not yet set up, do so now by following the instructions that came with your device. Also be sure the bridge has been setup. For instructions on how to set up your bridge and app, go to page ____. Fig. X 2. Download the Skill Use the “add a skill” (+) button inside your Alexa App. Search for the skill titled “My Curtains” or “Current Products”.
Integrate with Amazon Echo Plus- ZigBee 1. Set up your Echo If your Alexa device is not yet set up, do so now by following the instructions that came with your device. 2. Add a Device From the menu in the Alexa app, go to “Smart Home” and hit “Add a Device”. Alternately, you can say “Alexa, search for devices”. After Alexa has completed her search, pull down and release the TAU twice on each drapery you want to pair to Alexa. Fig. X Fig. X 3.
Integrate with Google Home Integrate with Control4 Integrate with Samsung SmartThings Troubleshooting 35
Using the DRapery Track Using the TAU for Operation The TAU, or Tug Activation Unit, can be pulled down or pushed up, depending on the desired movement. On a single drapery, pulling the TAU down activates the curtain. Pulling down once makes the curtain move towards the next position, depending on if the curtain is open or closed. Pushing the TAU up will stop it. Pulling down a second time after stopping will allow the curtain to move in the opposite direction.
Using the Remote Control- Single Drapery Full open Full Closed 66% Open 66% closed Channel Selector LED Indicators Full Open- A press and release moves the drapery to the full open position. A press and hold will move the drapery towards the open position, and stop it precisely upon release. Full Closed- A press and release moves the drapery to the full closed position. A press and hold will move the drapery towards the closed position, and stop it precisely upon release.
Using the Remote Control- Dual Drapery Full open primary Full Closed Primary Full Open secondary Full Closed secondary Channel Selector LED Indicators Full Open Primary- A press and release moves the drapery plugged into the motor 1 slot to the full open position. Full Closed Primary - A press and release moves the drapery plugged into the motor 1 slot to the full closed position. Full Open Secondary- A press and release moves the drapery plugged into the motor 2 slot to the full open position.
Using the Light & Temperature Sensors on the control housing Light Sensor Control Light Sensor LED Indicator Temperature Sensor Control Temperature Sensor LED Indicator Sensors Power Sensors Power LED Indicator Light Sensor Control - A press and release displays the current mode of the light sensor. A second press and release changes the mode of the automated movements triggered by the light sensor. Temperature Sensor Control- A press and release displays the current mode of the temperature sensor.
Sensor Modes The integrated light and temperature sensors have three possible modes: Off, Fully Automatic, and Semi-Automatic. Off- The device will not make any movement triggered by this sensor. Fully Automatic- The device will open and close the curtains based on the sensor readings. Semi-Automatic- The device will close the curtains based on sensor readings, but will not open them. These modes are indicated using the LEDs on the right of the control box.
SAFETY INFORMATION WARNING Read all warnings and instructions prior to installing the E-Wand™. Failure to follow these instructions may result in property damage or serious personal injury. CAUTION Do not use this product for anything other than its intended use. Any usage of the parts of this kit outside of its intended purposes in not covered under the warranty. CAUTION Drapery parts may have sharp edges. Use gloves to prevent cuts or abrasions whenever removing or reinstalling drapery.
RF WARNING STATEMENT This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated to provide a separation distance of at least 20 cm from all persons. Cet équipement est conforme aux limites d’exposition au rayonnement FCC / ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé de manière à assurer une distance de séparation d’au moins 20 cm de toutes les personnes.
been installed; (ii) Products which have not been regularly and properly serviced in accordance with the User’s Manual or which have otherwise been neglected; and (iii) ordinary wear and tear, service and maintenance and replacement items; (iv) the Product has been used, or attempted to be used, for other than the customary usage or for other than the Product’s intended use; (v) the Product has been subject to mishandling, misuse, or abuse; (vi) the product has suffered damage resulting from lightning, powe
