The SmartR Monitor Monitor User Guide 1 PowerSave Envi R Man.
Table of contents 2 How the EnviR works 3 EnviR Functions and Features Overview 4 Setting up your EnviR 5 Pair Display to the Transmitter 5 Sensable software – Voltage Adjustment 6 Sensable software – Pairing additional C² enabled displays to the transmitter 6 Install Transmitter and CT Clamps 7 Setting the Clock 8 Setting the Base Rate 8 Multiple Rate Tariffs 8 Advanced Features 9 Full System Reset 9 DATA output 9 Troubleshooting 10 Safety and care of your monitor 10 Limited
A big thank you for taking the decision to reduce your energy use. The planet needs more people like you. If we all do our bit to stop wasting electricity we can significant reduce our carbon footprint. The beauty of the EnviR is that it shows you how much energy you are using right now. It also shows you how much your electricity is costing every day and every month. The EnviR will allow you to take control of your energy use and SAVE Money while helping reduce your carbon footprint.
EnviR functions and features overview Before commencing installation please take a moment to review the components, buttons and display functions. Your Standard EnviR Kit includes: One Transmitter One Transmitter One Display Power Supply Two CT Clamps One Display One Installation Guide Antenna Signal Indicates number of CT clamps connected Shows how much energy you are using right now.
setting up your EnviR • Plug display power supply into back of display. • Plug display into convenient wall outlet. • Remove plastic battery tab from transmitter. • The red LED light on the transmitter should be flashing slowly. If not, check the batteries. • Check the display and compare it to the two images below to determine if the unit is paired. system is paired Electric pairing needed If the display looks likeEnergy the image to kW kW Energy NowNow theCost left Costdisplaying $ $ 0.
sensable software – Voltage adjustment The new Sensable software found in the EnviR transmitter allows you to set your known voltage. The default value shown on the display of 115. If you wish to change it please follow the instructions below: 1) Follow the steps for pairing the EnviR display and transmitter. 2) When you release the button the screen will show a tuning signal indicating the display is tuning to the transmitter.
Install Transmitter and cT clamps IMPORTANT: THIS DEVICE MUST BE INSTALLED BY A QUALIFIED/LICENCED ELECTRICIAN, UNLESS OTHERWISE PERMITTED BY LOCAL REGULATIONS. • Locate the main breaker panel that disconnects all power to the house. This enclosure is usually located close to the meter.
• Check the display to ensure that it is reading the signal and that watts are being displayed. • Re-attach the protective cover and close the panel. • Turn On the Main Breaker. setting the clock Energy Now Cost • Press the OK button for three seconds. • Use the UP ( ) or DOWN (V) buttons to adjust the hour. Night Day Eve Time Time setting the base Rate The unit has been programmed with a default rate of $0.1396 cents per kWh.
advanced features Additional transmitters The EnviR can be synced with up to nine additional transmitters. Uses include: • Monitor individual appliances or components. • Electrical usage of multiple users in apartment settings. • Solar or other alternative energy sources monitoring. • In order to sync an additional transmitter to the device simply press the UP ( ) or DOWN (V) buttons on the display and you will see Appliance number in the bottom right corner.
• A full cycle of history output can be initiated for download on demand by pressing and holding the DOWN (V) and OK buttons together until the LED flashes. Please note: all processor activity is halted during this download, even the clock, with a lot of history, the download may take some time! Self-resets when done. Troubleshooting Your EnviR monitor should reach you in perfect condition.
limited one year warranty PowerSave Inc. warrants this product for a period of one (1) year from date of purchase for all defects in workmanship or materials to the original user or consumer purchaser. This warranty excludes and does not cover defects, malfunctions, or failures caused by misuse, unauthorized repairs, modifications or accidental damage. All defective parts will be repaired free of charge or replaced. Note: This warranty does not apply to batteries.
The display has the following inputs/outputs:Powersupply and Datacable.The transmitter has three sensor inputs. Normal environmental conditions This equipment is designed to be safe at least under the following conditions: a) indoor use; b) altitude up to 2 000 m; c) temperature 5°C to 40°C; d) maximum relative humidity 80% for temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C; e) MAINS supply voltage fluctuations up to 10% of the nominal voltage.
