Installation guide

6 7
STEP
E
STEP
F
Multiple Rate Tariffs
The ENVI can be programmed to calculate different KWh unit rates for electricity
consumed at different times of day. In order to program different rates:
• Press and hold the UP and DOWN buttons together until the LED  ashes .
Then release both buttons.
• Using the UP and Down buttons you can select your low cost rate. Press the OK
button to confi rm rate.—If you do not select a different rate, then you will not see
the time section.
• You will see the clock  ashing. Using the UP and DOWN buttons you can now set the time that
your low rate starts. Press the OK button to confi rm.
• Using the UP and DOWN buttons you can set the time your normal rate starts. Press the OK button
to confi rm.
• Using the UP and Down buttons you can now select your normal cost rate. Press OK to con rm.
• The display will resume normal operation.
DATA output
• The ENVI will store up to 7 years of historical data. On the back of the display a USB cable can be
connected to facilitate both historical and real time data transfer to a MAC or PC.
• When installing the USB cable to the computer make sure you download the appropriate USB driver.
Please visit www.powersave.us for more information on available software downloads.
• Once the ENVI is connected to a computer the historical data will transfer automatically at 1 minute past
every odd hour, ie 17:01, 19:01 etc. A burst of data is sent once every 10 seconds. History Data is sent for
all 10 sensors regardless if they are now present or not.
• A full cycle of history output can be initiated for download on demand by pressing and holding the Down
and OK buttons together until the LED  ashes. Please note: all processor activity is halted during this
download, even the clock, with a lot of history, the download may take some time! Self-resets when done.
Troubleshooting
Your ENVI monitor should reach you in perfect condition. If you have connected it properly but cannot
get it to work, please check the following before contacting us for assistance.
Advanced Features
Additional transmitters
The ENVI can be synced with up to nine additional transmitters. Uses include:
• Monitor individual appliances or components
• Electrical usage of multiple users in apartment settings
• Solar or other alternative energy sources monitoring
• In order to sync an additional transmitter to the device
simply press the UP or DOWN buttons on the display and
you will see Appliance number in the bottom right corner.
When you reach the desired Appliance #, then pair the
transmitter per STEP A.
• PowerSave will introduce IAM (Individual Appliance Monitors) in Mid
2010 that will allow you to monitor up to nine individual outlets. Additional
transmitters can be ordered from your supplier or www.powersave.us
Multiple Displays
The transmitters can send their signal to an unlimited number of displays. Simply pair the display
with the other display(s) and transmitter(s). See STEP A.
Full System Reset
The ENVI can be fully reset to its factory condition. Resetting the ENVI will wipe out ALL historical
data and pairing information. To fully reset the ENVI:
• Remove the display power lead from the display
• Press and hold the UP and DOWN buttons as you push the display power lead into the back
of the display. When RED LED light  ashes release the buttons.
• The display will show software version number.
• Remove and reconnect the power lead on the display. This switch-on wipes all history and
pairing ID’s and burn in fresh defaults.
• Display unit will need to be paired again and rates need to be reprogrammed see Steps A-D.
Problem Possible Cause Solution
No display Faulty display and/or display power
supply
Contact Supplier
Corrupted display
(incomplete data)
Faulty display Contact Supplier
Alternating readings Display picking up a signal
from a neighbors transmitter
Pair your transmitter and
display again see Step C
Data does not change Incorrect installation Review quick set-up guide
Costs reading seems
excessively high or low
Correct tariff has not been set Refer to Steps F and G
Temperature gauge
excessively high
Display too close to heat source Choose a different location
Safety and care of your monitor
• Do not attempt to repair or service any part of the ENVI equipment. Contact our customer service
department for assistance.
• Do not immerse the product in water, or any other liquids.
• Do not expose the product to heat,  ame, steamy conditions or extreme cold.
• Do not open the equipment or touch any of its electronic circuitry.
• Do not hit, strike or drop the equipment—if the display gets broken, take special care not to
touch the liquid crystals.
• Do not use this product for any other purpose for which it was intended.