User guide
10 11
Understanding the EnviR display
When your EnviR display is properly installed you should see a screen similar to the image below:
Indicates the number of sensor jaws installed. For most
domestic situations this will be one
The top line of the display shows you how much energy
you’re using right now. Test it out by switching a light on
and off and watch the gures as they change
Aerial icon conrms information is being read from the
transmitter
The second line down shows how much money you’re
spending. It will also change as you switch electrical
goods on and off. The gures change automatically to
show how much it cost you per day and per month – if
you neglect to turn off your appliances
The third line shows you how much you save when you
turn an appliance off, or spend as you turn it on. It also
shows you the equivalent decrease or increase in energy
usage
This graph shows you how much energy you have used
between 7am to 3pm during the previous day, 3pm
to 11pm the previous evening and 11pm to 7am the
previous night
This shows you your accumulative energy in kWh and
scrolls every ten seconds between the last day, the last
seven days and the last 30 days. You can also scroll
through these using the OK
button
The time and the temperature are displayed at all times.
Setting up your EnviR – OptiSmart Reader Monitor
Setting up your EnviR display
1) Unpack the product. Plug the display screen into its mains adapter, and plug the mains
adapter into a wall outlet. The display screen will start working and probably show dashes
instead of numbers.
2) Plug the wire from the OptiSmart reader into the white OptiSmart transmitter box. Rotate the aerial on
the white OptiSmart transmitter to the upright position.
3) Remove the plastic battery tab from the back of the white OptiSmart transmitter unit; the transmitter
will now be activated.
4) The Sensor’s red light will start to ash every 6 seconds.
5) For the next step, you will need some information about your electricity meter. On its faceplate look
for a label that says ‘xxxx imp/kWh’ and note the number.
Pairing the EnviR display and transmitter – electronic meter ‘appliance 9’ screen
1) Place the white OptiSmart transmitter and the display screen in the same room.
2) Using a used match, pen or similar, push and hold the small button in the hole on the front until the
LED on the white OptiSmart transmitter has ashed ONCE, then release.
3) The LED will start to ash faster for about a minute.
4) At the display, use the UP
or DOWN
buttons to reach the ‘appliance 9’ screen. Now press
and hold the DOWN
button until the display’s red LED ashes, then release the button. The
display screen 9 will pair to the transmitter. This will show 1000 (default imp/kWh)
5) If the number is different from the imp/kWh on the electricity meter, use a used match, pen or similar
to press and release the small button in the hole on the sensor so that the number changes.
(The options are 100, 500, 600, 800, 1000, 1250, 1600, 3200, 10000).
After about a minute, the transmitters LED will revert to ashing once every 6 seconds. The display’s
appliance 9 screen will now say ‘DATA’. If the transmitter fast ashing stops before you are ready, do the
Electronic Meter pairing again from Step 1.
Display/Sensor pairing 2 – Main screen (Energy Now Data)
1) Place the white OptiSmart transmitter and the display screen in the same room.
2) Using a used match, pen or similar, push and hold the small button in the hole on the front until the
LED on the white OptiSmart transmitter has ashed three times, then release.
3) The LED will start to ash faster for about a minute.
4) At the display, use the UP
or DOWN
buttons to reach the main screen (this is the screen
that shows Temperature and Time). Now press and hold the DOWN
button until the display’s
red LED ashes, then release the button. The main display screen will pair to the transmitter, clear
and then revert to normal operation.
5) After about a minute, the sensor LED will revert to ashing once every 6 seconds. The displays main
screen will now show ‘0 Watts’. If the transmitter’s fast ashing stops before you are ready; start from
the beginning again.
2
OPTION