Instructions / Assembly

Technical Support: 1-800-721-7360, Monday-Friday, 8:00 a.m. – 4:30 p.m., CST
Installation
• For standard installation on 1/2-inch-14 NPS threads (most common thread on
US kitchen faucets) cold water line.
• Please read all instructions and precautions before installing and using the US-
EZ water filter.
• Numbered diagrams correspond with numbered steps.
1. Selecting the Faucet Location
NOTE: The drinking water faucet should be positioned with function, convenience and
appearance in mind. An adequate flat area is required to allow faucet base to rest
securely. The faucet fits through a 9/16-inch hole. Most sinks have pre-drilled 1
3
⁄8" or
1
1
⁄2" diameter holes that may be used for faucet installation. If these pre-drilled holes
cannot be used or are in an inconvenient location, it will be necessary to drill a 9/16-
inch or 5/8-inch hole in the sink to accommodate the faucet.
This procedure may generate dusts which can cause severe irritation
if inhaled or come in contact with the eyes. The use of safety glasses and respirator for
this procedure is recommended.
DO NOT ATTEMPT TO DRILL THROUGH AN ALL-PORCELAIN SINK.
If you have an all-porcelain sink, mount the faucet in pre-drilled sprayer hole or drill
through counter top next to sink.
When drilling through a counter top make sure the area below the
drilled area is free of wiring and piping. Make certain that you have ample room to
make the proper connections to the bottom of the faucet.
Do not drill through a counter top that is more than 1-inch thick.
Do not attempt to drill through a tiled, marble, granite or similar counter
top. Consult a plumber or the counter top manufacturer for advice or assistance.
A. Line bottom of sink with newspaper to prevent metal shavings, parts or tools from
falling
down the drain.
B. Place masking tape over the area to be drilled to prevent scratches if drill bit slips.
C. Mark hole with center punch. Use a 1/4-inch drill bit for a pilot hole, then, using
a 9/16-inch or 5/8-inch drill bit, drill a hole completely through the sink. Smooth
rough edges with a file.
2. Mounting the Faucet
A. Insert spout
A
into faucet body
B
.
Tighten by screwing the spout nut
C
onto
the threads on the faucet body.
B. Slide black rubber gasket
D
onto threaded faucet stem. Lower faucet stem
through hole in sink.
C. Accessing the faucet from underneath the sink, slide metal washer
E
up the fau-
cet stem, followed by the white plastic stem nut
F
. Tighten with fingers to secure
faucet to sink.
NOTE: do not use pliers to tighten stem nut. Pliers may strip the threads of the faucet
stem.
3. Installing the Water Supply Adapter
The supply adapter fits 1/2-inch-14 NPS supply threads.
A. Turn off cold water supply line.
B. Turn on the cold water faucet and allow all water to drain from line.
C. Disconnect cold water line from 1/2-inch-14 NPS threaded stub on bottom of
main faucet.
NOTE: If it is too difficult to access the threaded stub on the bottom of the cold
water faucet, see Alternate Installation on page 4.
D. Apply Teflon
®
tape onto male threads of faucet stub and supply adapter. Screw
the water supply adapter to the threaded faucet stub as shown.
E. Using the nut that previously connected the cold water line to the faucet, screw
the cold water line to the male supply adapter threads. Hand tighten nut and snug
with wrench.
WARNING:
CAUTION:
CAUTION:
CAUTION:
CAUTION:
2
1
A
B
C
A
B
F
D
E
C
3
A
B
C
D
E
2