3-in-1 Stainless Five Burner Gas Grill ASSEMBLY INSTRUCTIONS Model GAS9556AS / GAS9556ASO
ASSEMBLY INSTRUCTIONS: READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
20 19 18 21 14 16 23 25 13 11 15 26 12 8 10 17 6 9 27 28 5 3 4 1 2 7 22 24 2
FRONT PANEL Step 1 2 1 • Loosen 6 screws 3-4 turns • Do not remove screws • Attach FRONT PANEL 2 using keyholes • Tighten 6 screws 3 NOTE: Before tightening keyhole screws, make sure panels are aligned.
Step 3 • Loosen 2 screws • Attach LEFT SIDE PANEL 5 • Tighten 2 screws on LEFT SIDE PANEL 5 5 1 2 3 LEFT SIDE PANEL Step 4 CART BRACE 6 1 2 3 5 Remove 2 screws • Remove 6 screws. • Attach CART BRACE. 6 • Tighten two screws on CART BRACE.
Step 5 • Attach CART BASE 7 • • Make sure TANK BRACKETS are on this end.
Step 7 • Attach CART BASE 7 to back legs • Tighten 4 screws (Removed from Step 6) 7 CART BASE LEFT SIDE PANEL Step 8 Screws removed from Step 6 5 8 • Attach LEFT SIDE PANEL 5 and CART BRACE 6 • Tighten 4 screws 9 CART BRACE 10 6
CASTERS Step 9 unlocked • Lock CASTERS • Attach CASTERS to legs 7 Step 10 • • 7 6 GRIDDLE HOOKS Attach GRIDDLE HOOKS to LEFT SIDE PANEL 5 NOTE: Washer and nut used to attach GRIDDLE HOOKS go on the back side of LEFT SIDE PANEL.
Step 11a TOP VIEW 6 • Loosen 2 bottom screws Loosen bottom screws CART BASE Step 11b 6 Tighten screw BAR • Install BAR • Tighten 2 screws Tighten screw CART BASE 8
Step 12 • GRILL BODY Set GRILL BODY on cart Step 13 GRILL BODY Remove screw • Remove 3 screws • Align GRILL BODY to cart • Rotate CART BRACKETS upwards and tighten 4 screws Remove screw CART BRACKETS Remove screw GRILL BODY Tighten screws Align Panels 9
GRILL BODY Step 14 Remove screw Remove screw Remove screw • Remove 3 screws • Align GRILL BODY to cart • Rotate CART BRACKETS upwards and tighten 4 screws CART BRACKETS GRILL BODY Tighten screws Step 15 LEFT SIDE TABLE Remove screw and washer • RIGHT SIDE TABLE Remove screw and washer Remove 3 screws and washers RIGHT SIDE CONTROL PANEL Remove screw 10
LEFT SIDE CONTROL PANEL RIGHT SIDE CONTROL PANEL Step 16 • Loosen 4 screws • Attach parts and tighten screws Align edges LEFT SIDE TABLE RIGHT SIDE TABLE Step 17 • Loosen 4 screws • Attach LEFT SIDE TABLE using keyholes • Do not tighten screws at this point in time Loosen 4 screws LEFT SIDE TABLE 11
Step 18 • Install screw and tighten. (screw was removed in Step 13) Step 19 • Install screw and washer. (screw and washer were removed in step 15) Do not tighten screw at this time.
Step 20 • Loosen 4 screws. • Attach RIGHT SIDE TABLE using keyholes. Do not tighten 4 screws at this time.
Step 22 • Install screw and washer (screw and washer were removed in step 15) Do not tighten screw at this time.
Step 24a • Remove WING NUT and remove burner.
Step 25a • Attach WIRE CLIP to side burner SIDE BURNER SIDE BURNER VALVE WIRE CLIP Step 25b SIDE BURNER SIDE BURNER VALVE WIRE CLIP 16
Step 26 • Attach IGNITOR WIRE to ELECTRODE ELECTRODE IGNITER WIRE Step 27 • 17 Install SIDE BURNER GRATE SIDE BURNER GRATE
Step 28 • Loosen 2 screws • Attach HEAT SHIELD and tighten screws HEAT SHIELD Step 29 GREASE TRAY • Install GREASE TRAY and GREASE CUP through back of grill GREASE CUP 18
WARMING RACK Step 30 COOKING GRATES • Install HEAT TENTS,COOKING GRATES and WARMING RACK HEAT TENTS Step 31 • Store GRIDDLE on GRIDDLE HOOKS • Store SMOKE TUBE SMOKE TUBE STORAGE GRIDDLE STORAGE 19
Model GAS9556AS Assembled AI9556AS/ASO 1118 ©2018 The Boltz Group LLC Addison, Texas 75001 U.S.
