Assembly & Set-Up Thank You Thank you for purchasing this product, It was carefully engineered Lo provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain your machine, Please be sure that you, and any either persons who will generate the machine, carefully follow the recommended safety practices st ol times.
Place shift ravel in Forward-6 position ar fastest forward speed f equipped] Observe lawyer tear area of equipment 10 be sure bath cables fif equipped) are aligned and seated properly In rifler guides, See Figure 2-3. Attach the two carriage screws (b) and nuts {2} removed in Step 2. Finish securing the handle by tightening the top two nuts fc} loosened in Step 2. See Figure 2-5 or Figure 2-6 for pits with side supports.
T nsertacarviage screw () from the outside through & handier tab (b}, the upper (e} and lower handles (d), a saddle washer and anti the wing knob ], Repeat ort the other side. Tighten the wing nabs {f) on each side of the handle. Refer to Figure 29, Figure 2-9 Chute Assembly Options NOTE: The auger cable (2) austere down the leftward handle and the drive cable (b s routed crass the top of the lower fandom and down the right side of the lower handle. See Figure 2-16.
8 Standard Side Crank Chute Control Chute Assembly Standard Side Crank Rod Figure 2-12 1. Position chute assembly over base. See Figure 213, Section 2 — Assembly & Set-Us Close flange keepers to secure sate assembly ta chute base. Flange leapers wil click into place when properly secured, Ses Figure 214 Figure 2-14 NOTE: Ensure the lower chute s secured to the flange on the chute base. The lawyer edge of the chute keeper should be positioned below the flange on the chute base lefter being sicked into place.
Overhead Chute Control (w/ 2 Chute Control Rod) Chute Assembly Overhead Chute Control Rod Figure 216 1 Re rove wing nut () and hex screw (b} from chute control head and devils pin and teeter pin (d) from chute support bracket. Position Shiite assembly forward-facing) over chute base. See Figure 217, Chute Control 4. Head Chute Support Bracket Figure 217 3 Remove hairpin clip (3 from rear of sate control head.
#lace chute onto chute base and ensure chute control rod is positioned under handle panel. Install hex screw governed in Sta 1, but do not secure with wing nut at this time. See Figaro 325, 2-Way & 4-Way Chute Control 3 Chute Assembly Chute Control = Figure 2-25 4 Squeegeeing on joystick and rotate chaste by hand to face forward. The hales in chute control input will be facing up. See Figure 2:26. Chute Control Input Figure 2-22 Tap View 1.
Overhead Chute Control (w/ Flex Shaft & Steel Chute) Figure 2:20 1 Bemoan nuts (8 and hex screws (b) from chute support braces {this wil require two wrenches), See Figure 231, Chute Control Head @ Chute’ Assembly | Bracket Figure 231 2. Place chute assembly onto chute base and chute control hied onto chute support bracket See Figure 231, a Secure chute control head to chute support bracket with lock nuts (a) and fex screws (b} removed in Step 1.
Electric Chute Control Chute Assembly Chute Control Rod ar Manual Chute Control Rod Figure 238 1. Remove cotter pin {a), wing nut (b) and hex screw from chute control head. Remove clevis pin (d) and bio-tle cotter pin {e) from chute support bracket. See Figure 2-39, Chute Central Head t Chute Support Bracket Figure 2-39 NOTE: For smoothest operation, sables should all be to the left of the chute directional control rod. 12 Section 2 — Assembly & Set-Up 2.
Set-Up Chute Control Cable Routing (if Equipped) For units equipped with 2wy of 4wy chute control Joystick, electric chute control and/or chute-pitch constant, senate control cables are routed properly.
Shave Plate 3 NOTE: This procedure applies to units equipped with adjustable sheave plates only. To adjust the shave paler: 1. Engineering to run und iris out of fuel Do nat atwitter i pour fuel from the engine. 5. 2. Carefully pivot unit up and forward so that ft vests on auger housing, 5 % Loosen bearskin shoe bolts 3) on both sides of auger housing and remove carriage boles (b} and hex nuts (c which attach shave plate {d) o the bantam of the auger housing.
Shift Rod (if Equipped) if full range of speeds forward and reverse) cannot ba achieved, adjust shift rod as follows: 1. 4, 16 Place shift lever in fastest forward sped antipasti. framer cotter pin (s} and washer (b) from adjustment arise on shift rod and pullout from shift lever. See Figure 259, Figure-58 Make sure the shift lever on the back of the transmission is ratted downward 1o the full extent of its rotation.
