OPERATOR’S MANUAL Zero Turn Tractor Models 364, 365 & 365L IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
TABLE OF CONTENTS Content Page Important Safe Operation Practices................................................................... 3 Slope Gauge...................................................................................................... 6 Know Your Z-Series........................................................................................... 7 Operating Your Z-Series .................................................................................... 10 Making Adjustments ................
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol - heed its warning.
23. Muffler and engine become hot and can cause a burn. Do not touch. 24. Check overhead clearances carefully before driving under low hanging tree branches, wires, door openings etc., where the operator may be struck or pulled from the unit, which could result in serious injury. 25. Your machine is designed to cut normal residential grass of a height no more than 10“. Do not attempt to mow through unusually tall, dry grass(e.g., pasture) or piles of dry leaves.
Service 3. Periodically check to make sure the blades come to complete stop within approximately (5) five seconds after operating the blade disengagement control. If the blades do not stop within the this time frame, your unit should be serviced professionally by an authorized MTD service dealer. 4. Check parking brake frequently as it is subjected to wear during normal operation. Adjust and service as required. 5. Check the blades and engine mounting bolts at frequent intervals for proper tightness.
TO REDUCE THE RISK OF INJURY, DO NOT OPERATE MOWER UNLESS DISCHARGE CHUTE COVER OR GRASS CATCHER IS IN ITS PROPER PLACE. KEEP HANDS AND FEET AWAY FROM ROTATING PARTS. REMOVE OBJECTS THAT CAN BE THROWN BY THE BLADE IN ANY DIRECTION. WEAR SAFETY GLASSES. DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND. NEVER CARRY CHILDREN. S30015 USE EXTRA CAUTION ON SLOPES. DO NOT MOW SLOPES GREATER THAN 15.MOW UP AND DOWN, NOT ACROSS. AVOID SUDDEN TURNS, USE LOW GEAR. READ OPERATOR'S MANUAL. KEEP SAFETY DEVICES WORKING.
SECTION 3: KNOW YOUR Z-SERIES NOTE: Reference to right or left hand side of the mower is observed from the operating position. Drive Handles Throttle Lever And Choke Lever Indicator Panel Brake Pedal Parking Brake Pedal Speed Control Bar Lift Handle Right Control Panel Figure 1 Read this operator’s manual and safety rules before operating your Z-Series. Compare the illustrations in this manual with your unit to familiarize yourself with the location of various controls and adjustments.
Electric PTO (Power Take-Off) Switch The PTO switch is located on the right control panel and it is used to control the engagement of the cutting blades. When the switch is up, the cutting blades are engaged. When the switch is down, the cutting blades are disengaged. See Figure 1 and Figure 2. NOTE: The PTO switch must be in the disengaged (OFF) position when starting the engine, when shifting into reverse, and when the operator leaves the seat.
• • Battery: The BATTERY indicator light will illuminate any time the ignition key is in the ON position and the engine is not running. If it illuminates while the engine is running, then the battery is in need of a charge. Refer to the MAINTENANCE section of this manual for the proper battery charging procedure. Temperature: (Liquid Cooled Models Only) Stop the engine immediately. Check clean air intake and cooling areas.
SECTION 4: OPERATING YOUR Z-SERIES Gas and Oil Fill-Up WARNING: Always remove the key from the ignition switch to avoid accidental starting. Service the engine with gasoline and oil as instructed in the separate engine manual packed with your mower. Read instructions carefully. Safety interlock Switches IMPORTANT: Your unit is shipped with oil; however, you • MUST check the oil level before operating. Be careful not to overfill. Overfilling with oil may cause the engine to smoke.
• If safe for operation, walk the slope and look for hazards such as rocks, mounds, ruts, stumps, or other irregularities. • After removing debris and identifying irregularities of the slope, back the Z-Series up the steepest slope you intend to work. If it cannot negotiate the slope in reverse, the slope is too steep. Use the following guidelines when operating on a slope: • • • • • • • Position the Z-Series on a flat and level surface and engage the parking brake.
Release Handles = Neutral / Stop Pull Handles Equal Back = Straight Reverse Push Handles Equal Forward = Straight Forward Full Right Forward And Full Left Back = Zero Turn Left Full Right Back and Full Left Forward = Zero Turn Right Right Neutral And Left Forward = Right Turn Right Forward And Left Neutral = Left Turn Right Neutral And Left Back = Reverse Left Right Back And Left Neutral = Reverse Right Figure 10 SECTION 5: MAKING ADJUSTMENTS Adjusting the Mower Deck Height Adjusting the Seat Pos
Checking the Brake Adjustment Adjusting Brake Force • • Position the Z-Series on a level surface and move the throttle lever to the slowest position (turtle). • Stop the engine, remove the key from the ignition, and engage the parking brake. • Release both hydraulic relief levers. • From the rear push on the frame and try to move the Z-Series. If you can move it, then the brake force must be increased. Go to ADJUSTING BRAKE FORCE.
• Remove bolts that secure linkage to upper control handles and lower control arms. The shock absorbers should remain connected to linkage. See Figure 12. Hex Bolt • With quarter inch by seven inch pins still installed in the top and bottom linkage arms, loosen the jam nuts at both the front and rear ends of linkage that runs from bottom linkage arms to hydrostatic pumps. See Figure 13.
Deck Lift Pivot Grease Fittings Pivot Bar Grease Fitting Caster Wheel Spindle Grease Fitting Caster Wheel Grease Fitting Lift Handle Grease Fitting Control Tower Grease Fittings 44” Mower Deck Grease Fittings 54” Mower Deck Grease Fittings Figure 14 Engine mended at the start of each mowing season. Check engine manual for correct plug type and gap specifications. Refer to the separate engine manual for engine maintenance instructions. Service air cleaner every 25 hours under normal conditions.
Checking Hydraulic Oil • Check the oil level of hydraulic units only when the engine is OFF. Pour proper amount of hydraulic oil level, insert the dipstick, and check the hydraulic oil level. Draining Hydraulic Oil During initial break-in (first five hours of operation), check oil before each use and after every hour of operation. • • During normal operation, check oil after 50 hours of operation.
• • • • • • • Slide the boot cover all the way up (toward the drive handles) to access the drive handle bolts. Remove drive handle bolts, drive handles, and rubber boot. Remove the four bolts securing the retaining plate to the control tower cover. Pull up on the control tower cover and slide up and over the control tower. Locate the rear of the light fixture where the wire attaches. See Figure 17.
• • Carefully pull the belt up and over the right hydrostatic cooling fan and then lift up and over the left hydrostatic cooling fan. Pull the drive belt out of the unit. • • Installing Drive Belt • • Set the parking brake and insert drive belt up and over the left and right hydostatic cooling fans. Do not place the belt into the drive pulley groves at this time. • Place the drive belt into the top groove of the engine pulley and route the belt to the inside of the idler pulley.
• Lock Nut • • Front Lift Rods Adjustable Link Jam Nut Lift Link Figure 21 Shoulder Screw Removing The Mower Deck WARNING: Do not remove deck immediately after operating the tractor. Allow the engine and other moving parts ample time to cool down. • • • Support Pin Hanger Bracket Position the Z-Series on a hard flat surface and engage the parking brake. Move the lift handle to the L position. Remove belt covers by removing the hex nuts or wing nuts that hold on the covers. See Figure 22.
54” Deck Belt To Clutch Pulley Retaining 44” Deck Bracket and Front Lift Rod Figure 27 Installing The Mower Deck • • • • • Retaining 54” Deck Bracket and Front Lift Rod • Slide the mower deck under the Z-Series, making sure belt covers are removed. From the rear, reach under the muffler cover and grasp the belt from the mower deck and bring it between the hydraulic units. Bring the belt between the pulley and the clutch. Do not put the belt into the pulley grove yet.
Mower Blades • Secure the mower blade by putting a piece of wood between the blade and the housing. See Figure 29. • Remove the hex flange nut that secures the blade to the spindle assembly. It is extremely important that each cutting blade edge be ground equally to maintain proper blade balance. An unbalanced blade will cause excessive vibration when rotating at high speeds, may cause damage to the unit, or result in personal injury. The blade can be tested by balancing it on a round shaft screwdriver.
Models 364, 365, & 365L 1 2 4 5 3 9 20 10 8 21 22 11 6 6 16 6 7 15 12 23 29 17 13 28 26 25 18 24 19 14 30 31 32 36 27 37 38 35 33 39 6 34 24 6 25 22
Models 364, 365, & 365L REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. PART NO. 731-3263 712-3004A 710-0451 731-3185 735-0251 710-0642 703-2648 712-0431 703-2807B 710-3168 749-3081 703-3288 710-0276 731-3310 726-0289 731-3128A 736-0242 720-0241 738-0754 720-0302 REF. NO. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. DESCRIPTION Control Handle Flange Lock Nut 5/16-18 Carriage Bolt 5/16-18 Bellow Foot Pad Hex Washer Screw 1/4-20 x .
Models 364, 365, & 365L 1 3 2 4 5 6 9 7 10 8 12 11 13 14 15 9 7 4 16 25 17 19 20 18 7 21 22 24 23 24
Models 364, 365, & 365L REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. PART NO. 603-0649 714-3004 710-3178 741-0324 703-3400 747-3404 714-0104 710-0134 712-3027 703-3405 714-0101 703-2857 732-0827 747-3397 735-0664 603-0683 711-3357 712-0314 736-0258 712-0431 747-3266A 732-0463 732-0800 747-3284 747-3363 DESCRIPTION Parking Brake Shift Ass’y Cotter Pin Carriage Bolt 3/8-16 x .75 Hex Flange Bearing .506 ID x .
Models 364, 365, & 365L 9 15 15 17 21 21 7 9 17 20 36 6 23 20 36 24 8 9 25 14 27 5 23 12 16 17 25 14 27 14 24 15 33 21 33 17 9 37 11 15 26 33 19 1 12 10 21 9 28 10 33 31 2 15 30 15 19 10 11 33 29 9 9 3 33 26 33 4 19 33 15 18 34 13 21 22 35 22 13 15 32 21 18 19 26
Models 364, 365, & 365L REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. PART NO. 603-0340 603-0341 603-0342 603-0343 603-0647 603-0410 603-0411 710-0216 710-3005 710-3178 711-1111 711-1124 712-0312 712-0365 712-0431 712-0453 712-0711 712-3001 712-3004A REF. NO. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37.
Models 364, 365, & 365L 61 62 1 63 9 2 3 44 64 5 4 63 10 8 6 62 7 65 66 11 12 13 12 18 25 26 13 22 67 30 21 19 14 20 15 27 29 16 28 17 23 53 24 38 46 54 31 32 50 33 36 40 41 45 68 43 37 35 34 51 52 47 39 42 55 56 9 44 48 57 42 58 59 49 60 37 28
Models 364, 365, & 365L REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. PART NO. 737-3069 737-3070A 603-0639 727-3116 721-0223 738-0940 727-3120 727-3155 727-3154 727-3121 727-3153 710-0216 712-0455 747-3360A 710-0378 736-3089 723-3071 731-1449A 712-0333 703-3168 756-0625 738-0924 703-3169 712-0117 618-3165 712-3050 710-0347 736-0258 756-0627B 703-3174 712-3019 736-0171 736-3015 603-0377A REF. NO. 35. 36. 37. 38. 39.
Models 364, 365, & 365L 1 4 2 7 6 3 2 8 REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. PART NO. 618-3110A 712-3004A 715-0136 717-3396 717-3455 718-3053 721-0343 727-3125 DESCRIPTION Drive Ass’y Complete Hex Flange Lock Nut 5/16-18 Spiral Pin 3/16 x 1.25 Spur Gear 14T Hydro Transmission Parking Brake Lever O-Ring 2.0 Dia.
Models 364, 365, & 365L 7 1 3 16 4 7 18 15 5 22 11 8 2 5 12 13 10 24 14 19 9 23 17 20 21 5 5 6 REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. PART NO.
Model 364 4 5 6 7 1 2 3 8 9 18 20 22 21 23 13 10 15 14 17 16 19 30 31 32 33 35 12 34 24 29 39 36 38 37 24 25 40 41 26 42 28 45 44 27 46 47 32 43 11
Model 364 REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. PART NO. 751-3141 751-3142 751-3140 710-3009 746-3070 746-3069 712-0161 710-0751 736-3006 736-0270 726-0205 751-0535 725-3001 712-0291 736-0119 712-3010 712-3071 712-0431 703-2859 710-3178 710-0642 721-0460 751-0650 710-1314 REF. NO. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47.
Model 365 4 5 6 1 8 9 7 12 10 11 2 3 14 16 13 15 21 17 20 19 18 25 22 8 23 26 24 27 29 28 31 30 32 33 34 35 37 36 39 38 40 34
Model 365 REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. PART NO. 751-3141 751-3142 751-3140 710-3009 746-3070 746-3066 710-3008 726-3008 712-3004A 749-3048 726-0205 725-1711 712-0161 736-0607 751-0535 712-0431 736-0258 747-3362 751-0644A 710-3178 751-0645 REF. NO. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. DESCRIPTION Oil Drain Hose Oil Drain Cap Oil Drain Screw #10-24 x .750 Throttle Control Cable 40.5” Choke Control Cable 38.
Model 365L 8 1 9 10 11 2 3 7 5 6 4 12 23 24 15 16 22 13 14 17 15 18 19 13 20 21 25 26 27 28 29 30 31 32 33 36
Model 365L REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. PART NO. 751-3141 712-3004A 703-3023 710-3008 726-0205 751-0535 710-0216 710-3009 746-3071 746-3068 712-0161 736-0607 726-3008 712-0431 736-3010 736-0258 747-3362 REF. NO. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. DESCRIPTION Oil Drain Hose Flange Lock Nut 5/16-18 Mounting Muffler Bracket Hex Cap Screw 5/16-18 x .75 Hose Clamp Fuel Line Hose Hex Cap Screw 3/8-16 x .75 Screw #10-24 x .
Models 364 & 365 2 3 4 5 29 6 17 18 7 8 16 17 9 11 12 21 22 19 13 15 14 20 10 30 31 32 23 24 34 28 25 9 26 27 38 33
Model 364 & 365 REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. PART NO. 629-3070 723-0455 710-3013 703-2809 712-3027 725-1718 703-2836 710-0134 725-3164A 725-0157 725-1347 725-1346 725-3163 783-0462 725-1722 725-3253 712-0397 712-0271 DESCRIPTION Wire Harness, Main - Not Shown Foam Protector, Indicator Light Hex Cap Screw 1/4-20 x .50 Bracket, Indicator Bulb Mtg. Nut, Hex Flange Lock, 1/4-20 Relay Bracket, Headlight Mtg. Carriage Screw 1/4-20 x .
Model 365L 2 3 4 5 29 6 18 7 8 17 16 17 9 11 12 21 22 19 13 15 14 20 10 31 32 33 23 24 35 28 25 30 26 27 40 34
Model 365L REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. PART NO. 629-3071 723-0455 710-3013 703-2809 712-3027 725-1718 703-2836 710-0134 725-3164A 725-0157 725-1347 725-1346 725-1717 783-0462 725-1722 725-3254 712-0397 712-0271 DESCRIPTION Wire Harness, Main - Not Shown Foam Protector, Indicator Light Hex Cap Screw 1/4-20 x .50 Bracket, Indicator Bulb Mtg. Nut, Hex Flange Lock, 1/4-20 Relay Bracket, Headlight Mtg. Carriage Screw 1/4-20 x .
Models 364, 365, & 365L 1 2 6 5 3 8 4 7 9 10 11 12 14 15 13 16 17 18 42
Models 364, 365, & 365L REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. PART NO. 757-0375B 757-3009 731-3154 710-1260A 738-0372 720-0190 732-3098 712-3004A 603-0294 710-0788 736-0463 750-3276 738-0296 712-3005 732-3080 750-0664 603-0730 710-0560 DESCRIPTION Seat Ass’y Seat Arm Ass’y (If Equipped) Seat Slide Hex Washer Screw 5/16-18 x .750 Shoulder Spacer Height Adjuster Knob Spring Index Flange Lock Nut 5/16-18 Seat Base Bracket Ass’y Hex Washer Screw 1/4-20 x 1.0 Flat Washer .
Models 364, 365, & 365L 2 1 3 40 27 4 26 5 6 15 21 9 7 25 24 10 4 12 8 11 13 14 22 21 17 16 20 19 18 28 29 30 32 33 31 34 35 37 36 38 20 39 44 23
Models 364, 365, & 365L REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. PART NO. 711-0642A 731-3158 732-3097 747-3405 738-0507B 710-0216 603-0422 603-0370 603-0313 703-2621 703-2780 603-0327 703-2772 738-3150 712-3020 603-0423 710-3083 711-0773 738-0380 712-0206 REF. NO. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. DESCRIPTION Handle Button Handle Deck Lift Grip Compression Spring Front Lift Rod Shoulder Screw .500 Dia x .
Models 364, 365, & 365L 1 2 3 4 5 6 12 8 7 9 10 11 13 12 20 2 12 14 15 16 17 19 18 REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. PART NO. 712-3075 736-0274 603-0389A 737-3090 737-3072 712-0431 712-0229 710-3178 710-0514 736-0169 REF. NO. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. DESCRIPTION Hex Lock Nut, 1.0-14 Flat Washer Pin Ass’y, Pivot Adapter, 1/8 NPTF x 1/8 NPTF Grease Fitting, 65° w/Extension Hex Flange Lock Nut, 3/8-16 Push Nut, 3/8 ID Carriage Bolt, 3/8-16 x .75 Hex Cap Screw, 3/8-16 x 1.
Model 364 3 1 2 4 7 8 9 5 14 15 7 16 4 6 11 10 17 12 18 13 19 20 REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. PART NO. 712-0251 603-0720B 712-0455 712-0431 710-0216 710-3144 712-3004A 736-0258 749-3087 749-3089 DESCRIPTION Retainer Nut 3/8-16 Frame Assembly Retainer Nut 3/8-16 Flange Lock Nut 3/8-16 Hex Cap Screw 3/8-16 x .75 Hex Cap Screw 3/8-16 x 2.0 Flange Lock Nut 5/16-18 Flat Washer .385 x 1.0 x .135 Upper Bumper Tube Lower Bumper Tube REF. NO. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
Models 365 & 365L 3 1 2 4 7 8 9 5 7 4 6 11 10 12 13 REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. PART NO. 712-0251 603-0720B 712-0455 712-0431 710-0216 710-3144 712-3004A 736-0258 749-3062 DESCRIPTION Retainer Nut 3/8-16 Frame Assembly Retainer Nut 3/8-16 Flange Lock Nut 3/8-16 Hex Cap Screw 3/8-16 x .75 Hex Cap Screw 3/8-16 x 2.0 Flange Lock Nut 5/16-18 Flat Washer .385 x 1.0 x .135 Upper Bumper REF. NO. 10. 11. 12. 13. 14. 15. 16. 17. 18. 48 PART NO.
Models 364, 365, & 365L 1 4 2 1 3 5 6 2 7 3 8 8 9 9 10 11 11 10 REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. PART NO. 722-0265 710-1260A 736-0231 651-3004 703-3490 712-0431 710-0216 734-1596 734-3163 634-3005 634-3030 734-0255 634-3050 634-3051 634-3052 DESCRIPTION Foam 2.04 x 3.50 x .62 Hex Washer Screw 5/16-18 x .75 Flat Washer .344 ID x 1.125 OD Tank Assembly 4.0 Gallon Fuel Tank Mounting Bracket Flange Lock Nut 3/8-16 Hex Cap Screw 3/8-16 x .
Model 364 1 4 10 5 8 7 6 11 9 12 19 2 3 28 20 13 21 14 31 32 15 30 17 13 34 27 35 19 37 38 36 43 24 18 24 39 68 42 44 23 46 23 6 29 33 22 8 16 26 25 67 41 47 45 65 66 70 50 48 24 60 49 63 51 52 42 19 56 53 57 62 24 69 58 54 2 59 55 50 61 64
Model 364 REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. PART NO. 732-0556 712-3006 710-0597 710-3151 736-0290 741-0524 754-3091 716-3020 750-3164 712-0239 736-0179 736-0188 741-0338 750-0656 756-3108 732-0850 603-0743 736-0100 737-3000 738-3172 603-0741 732-3067 756-3005 712-0431 748-3100 603-0763 712-3004A 703-2559 710-3008 726-3045 703-3742 712-3010 736-0119 738-0213 736-0192 DESCRIPTION Extension Spring .
Model 365 & 365L 1 65 2 3 4 5 1 6 8 66 9 6 7 10 70 15 7 13 12 11 67 14 17 20 7 30 9 28 69 7 71 11 18 19 20 7 28 10 68 16 29 31 32 68 22 6 7 21 7 26 9 27 22 33 34 23 24 25 42 7 58 57 55 59 44 41 35 36 37 39 43 38 22 40 56 54 46 53 44 45 72 62 47 52 48 31 45 61 63 51 49 49 50 64 52 60
Model 365 & 365L REF. NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. PART NO.
Model 365 & 365L 1 2 4 7 3 6 3 5 6 2 4 5 7 REF. NO. 1. 2. 3. 4. 5. 6. 7. PART NO. 732-0772 711-0509 712-3007 712-0116 711-1059 736-0159 710-1207 DESCRIPTION Extension Spring 1.25 OD x 11.5 Lg Spring Hex Jam Nut 5/16-18 Jam Lock Nut 3/8-24 Ferrule Washer 5/16 Hex Cap Screw 5/16-18 x 3.
Models 364, 365, & 365L 629-3071 629-3070 55
MANUFACTURER’S LIMITED WARRANTY FOR: TWO-YEAR RESIDENTIAL ONE-YEAR COMMERCIAL Proper maintenance of your Cub Cadet equipment is the owner’s responsibility. Follow the instructions in your operator’s manual for correct lubricants and maintenance schedule. Your Cub Cadet dealer carries a complete line of quality lubricants and filters for your equipment’s engine, transmission, chassis and attachments.
