Operator’s Manual Twin Rear Bagger - Model No. 19C70020100 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA FORM NO.
1 To The Owner Thank You Thank you for purchasing a bagging attachment manufactured by Cub Cadet. It was carefully engineered to provide excellent performance when properly operated and maintained. Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain your equipment. Please be sure that you, and any other persons who will operate the machine, carefully follow the recommended safety practices at all times.
Important Safe Operation Practices 2 WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! DANGER! This attachment was built to be used according to the safe operation practices in this manual.
3. Use slow speed. Choose a low enough speed setting so that you will not have to stop or shift while on the slope. Tires may lose traction on slopes even though the brakes are functioning properly. Always keep machine in gear when going down slopes to take advantage of engine braking action. 4. Follow the manufacturer’s recommendations for wheel weights or counterweights to improve stability. 5. Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction.
(OK) Figure 1 line Slope Gauge 10° Slope 1 0 ° d a s hed USE THIS SLOPE GAUGE TO DETERMINE IF A SLOPE IS TOO STEEP FOR SAFE OPERATION! To check the slope, proceed as follows: 1. Remove this page and fold along the dashed line. 2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.) 3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ). 4. Adjust gauge up or down until the left corner touches the slope (See Figure 1 and Figure 2). 5.
3 Contents of Carton Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Fig. 3-1. Three hardware packs are included in this kit and are detailed on the following page. • Upper Chute Support • Hitch Bracket Kit (5 Pcs.
CONTENTS OF HARDWARE PACK This grass collector kit is shipped with three loose hardware packs enclosed and one set of hardware included in the mounting bracket kit. Please check your hardware packs against the illustrations below. The quantities for each item is listed in parenthesis.
4 Assembly & Installation NOTE: References to left, right, front and rear of the tractor are from the operator’s position, unless otherwise stated. • Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake. • For convenience, pivot the seat forward and leave it in that position until the grass collector is fully mounted and assembled.
3. 4. Install the upright support bracket onto the mounting assembly on the tractor by hooking it over the mounting assembly between the two tabs as indicated in (1) Figure 4-4. Secure the upright support bracket to the mounting assembly in the proper mounting hole based on deck size, with a 710-0376 hex bolt and 712-04063 flange lock nut from hardware pack 689-00320. See (2) Figure 4-4.
Make sure screen sits under the cover’s lip Figure 4-10 Figure 4-8 4. Install the bagger cover onto the bag support assembly, as shown in Figure 4-9. The plastic cover goes inside of the two mounting tabs. 6. Figure 4-11 Open Hood by pushing in on the rear, right-side tab with your right hand, as shown in 1 of Figure 4-12, and lifting the cover with your left hand in the center rear of the bagger cover, 2. Figure 4-9 5. Slide the hinge pin into the hole located on the mounting tab, as in Figure 4-10.
7. Install both bag assemblies onto the bag support brackets by inserting the front edge in first, as shown in 1 of Figure 4-13, and setting the back edge down until it fits into the assembly (2). 4. Secure the chute elbow to the deck using the wing knob 720-04122 from hardware pack 689-00318A. See Figure 4-15. 1 2 Figure 4-13 Figure 4-15 Install the Deck Chute Elbow Determine if your deck is a newer model, or an older model. Refer to (1) in Figure 4-14.
Tractors With Older Deck Configurations 1. Install one of the rubber chute straps onto the chute elbow using one of the supplied clevis pins (711-05063), washer (736-0204) and Bow-tie cotter pins (714-04040) from hardware pack 689-00318A. See Figure 4-16. Secure the end of the strap utilizing the hole furthest from the end, insert the smaller hook end of the torsion spring hook (732-04510A) into the other end.
Installing the Deck Chute 1. 3. Peel the backing off of the self-adhesive foam strip (721-04388) that has been included within your Carton of Contents. Apply it to the upper chute, flush against the flange as shown in Figure 4-19. With the ability now to wiggle the discharge chute tube back and forth, slide it over the chute elbow mounted on the cutting deck, as shown in Figure 4-21. Flange Figure 4-21 4. Figure 4-19 2.
Install The Counter Weight RZT Models with a Fixed Front Axle The front weight kit is designed for use with all RZT-L (Lap Bar) Residential Zero-turn models. The front weight kit is NOT designed nor required for use with all RZT-S (Steering Wheel) Residential Zero-turn models. 1. Attach the left mounting bracket and the right mounting bracket to the weight bar using two 21⁄2-inch screws (7100859), and 3⁄8” flange nuts (712-04065) from hardware pack 689-00325. See Figure 4-24.
4 Operation Bagger Usage NOTE: When both grass bags are full, place the tractor on a firm, level surface, disengage the PTO, turn the tractor engine off and set the parking brake. 1. Pivot the seat forward. 2. Open the grass catcher hood by pushing in on the rear, right-side tab with your right hand, as seen in 1 of Figure 5-1, and lifting the cover with your left hand in the center rear of the bagger cover, 2. 2 1 Figure 5-2 2 1 5.
Notes 16
Notes 17
19C70020100 Parts List 2 16 7 5 12 3 15 8 22 17 7 4 15 12 34 30 13 36 29 9 11 27 12 5 10 6 12 14 28 25 26 26 1 20 19 23 18 24 31 33 32 18 21 35
Ref. Part Number Description 1. 603-05204 Upper Chute Assembly 2. 931-04292 Twin Bagger Cover Assembly 3. 731-06497 Upper Chute Support 4. 731-06504 Bagger Cover Screen 5. 710-0276 Carriage Screw, 5/16-18 x 1.00” 6. 710-0376 Hex Head Screw, 5/16-18 x 1.00” 7. 911-0310 Clevis Pin, .50” Dia. x 1.18 8. 964-04090A Grass-bag Assembly 9. 683-04461A-0637 Twin Bag Support Assembly 10. 683-04519B-0637 Vertical Support Bracket 11. 711-04988 Cover Hinge Pin 12.
CUB CADET LLC MANUFACTURER’S LIMITED WARRANTY FOR SEPARATELY SOLD ATTACHMENTS AND ACCESSORIES IMPORTANT: To obtain warranty coverage owner may be required to present an original proof of purchase and applicable maintenance records to the servicing dealer. Please see the operator’s manual for information on required maintenance and service intervals.
