Warranty

5
ASSEMBLY & SET-UP
3. Secure with self-tapping screw (710-04683C)
from hardware pack 689-02139. See Figure 8.
4. With lift handle in up position and plow resting
on the ground, feed one cable (746-04794)
through arc-shaped hole in front mounting
bracket assembly (689-02459) and frame. See
Figure 9.
5. Reaching between front mounting bracket
assembly (689-02459) and plow assembly
(689-02100), draw cable and lock pin arm
through curved slot. See Figure 10.
6. Attach end of plow lift cable lever by inserting
z-bend of cable into hole located on lock pin
and rotating z-bend. See Figure 11.
7. Slide top nut and washer up and into
mounting slot located on lift handle assembly
(689-02499). See Figure 11.
8. Pull lock pin assembly cable taut, use 1/2”
wrench to hold inside nut while tightening
outside nut with second 1/2” wrench.
NOTE: Cable is adjustable by loosening or tightening
the nuts.
Attach Cable to Lever Lock
1. Attach end of pivot release cable lever to lever
lock by inserting z-bend of cable into hole
located on lever lock assembly
and then rotating cable assembly
vertically.
2. Slide top nut and washer up and
into mounting slot located on
lever lock mounting bracket. See
Figure 12.
3. Pull pivot release cable taut, use
1/2” wrench to hold bottom nut
while tightening top nut with
second 1/2” wrench.
Attach Control Handle To
Pivot Assembly
1. Working from top-down, secure
lower control tube (749-07634) to
plow assembly (689-02100) pivot
plate on right side directly behind
plow with shoulder screw (738-
0143), flat plastic washer (736-
0414) and hex flange lock nut
(712-04065) from hardware pack
689-02139. See Figure 13.
NOTE: Flat plastic washer (736-0414)
should be installed on top side of bracket
under lower control tube (749-07634). See
Figure 13.
2. Connect ring (603-0297) to lift
handle assembly (689-02499) with
hex flange lock nut (712-3004A)
from hardware pack 689-02139.
See Figure 14.
3. Feed upper control tube (749-
05855A) through guide ring on lift
handle. See (1) in Figure 15.
4. Working from inside-out, attach
upper control tube (749-05855A)
to lower control tube (749-07634)
with two curved carriage bolts
(710-1250), two curved washers
(736-0451) and two hex flange
lock nuts (712-04063). See (2) in
Figure 15.
5. Install end plug (735-0246A) from
hardware pack 689-02139 into
end of lift handle (689-02499).
6. Mount cable levers (746-04794)
from hardware pack 689-02139
to upper control tube with two
screws (710-1625). See Figure 16.
NOTE: Cable closest to grip goes to lock
pin and forward cable goes to lever lock.
7. Secure cables to control tube with
two zip-ties (726-04111) from
hardware pack 689-02139 - one
two inches below ring on lift
handle and one near bottom bend
of lower control tube.
8. Slide grip (720-0274) from
hardware pack 689-02139 over
upper end of control tube (749-05855A).
Plow Removal
To remove the plow continue as follows:
1. Lock plow in up position.
2. Remove front mounting bracket
from frame by unscrewing two
wing knobs (720-04186) and
carriage bolts (710-1649).
3. Remove “H” bracket assembly
from larger plate mounted to
underside of tractor foot pan
by removing the two clevis pins
(711-05217) and two bow tie pins
(714-05005).
4. Move plow to down position.
5. Slide plow assembly away from
tractor. See Figure 17.
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
1
2
Figure 15
Figure 16
Figure 17
Install Front Mounting Bracket
IMPORTANT: The frame mount hardware installed on the front mounting bracket is for ZT
models only. For ZTX models, remove 4 rubber spacers and associated hardware prior to
attaching large mounting bracket to tractor frame. See circles and note in Figure 4.
1. Mount front mounting bracket
assembly (689-02459) by
aligning rear of assembly with
front of tractor and sliding
upper lip over and lower lip
under frame. See Figure 4.
2. Working from the bottom
up, secure bracket to tractor
frame with two carriage bolts
(710-1649), two spacers (750-
06527) and two wing knobs
(720-04186) from hardware
pack 689-02139. See Figure 4
inset.
NOTE: Hole placement differs
between models. Use inner holes for ZT
models and outer holes for ZTX models.
See Figure 4.
3. Swing “H” assembly bracket
previously installed up to meet
front mounting bracket. See
Figure 5.
NOTE: “H” bracket assembly arms
should fit between the two sets
of U-channels on backside of front
mounting bracket. See Figure 5.
4. Working from the inside out,
secure with two clevis pins
(711-05217) and two bow tie pins
(714-05005) from hardware pack
689-02139. See Figure 5 inset.
5. Insert flanged bearings (741-0192)
from hardware pack 689-02139
into front mounting bracket. See
Figure 6.
Attaching Plow and Lift
Handle Assemblies
1. Bring plow assembly
(689-02100) up from
underneath front
mounting bracket (689-
02459) and fit between
flanged bearings (741-
0192). See (1) in Figure 7.
TIP: May be necessary to have
two people to perform this step.
2. Holding plow assembly in
place, slide lift handle
assembly (689-02499) into
position, making sure to
slide shaft through both
bearings. See (2) in Figure 7.
Remove for ZTX
Models
Figure 4
Figure 5
Figure 6
1
2
Figure 7
Figure 8