Install Manual

ManualsBrandsCub Cadet ManualsLawn Mower Bags50 in., 54 in. and 60 in. Triple Bagger for the Ultima ZT2 Series Zero Turn Lawn Mower (2019 and After)

Contents of Carton

Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below

and shown in Figure 3-1. The hardware packs included in this kit are detailed at the end of this section.

• Boot Assembly - 631-18371

• Grass Bag Assembly (3) - 664-05104

• Vertical Bagger Support - 683-04519C

• Grass Bag Support - 683-04498B

• Chute Adapter - 731-10133

• Bagger Top Assembly - 631-06539

• Hose - 764-05275

• Hinge Pin - 711-05079

• Bag Deflector - 731-18471

• Hitch Adapter Bracket - 789-02137

• Bagger Screen - 731-06504

• RZT Bagger Weight - 719-04217A

• Weight Plates (3) - 789-02137

• Weight Hanger Bracket Left - 789-02197

• Weight Hanger Bracket Right - 789-021978

• Hardware Pack - 689-01419

• Hardware Pack - 689-02199

• Deflector Hardware - 689-02299

• Anti-marking Adhesive Strips - 777X52246

Figure 3-1

50/54/60" Triple Bagger 19A70056100

Summary of content (6 pages)

PAGE 1
3 Contents of Carton 50/54/60" Triple Bagger 19A70056100 Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Figure 3-1. The hardware packs included in this kit are detailed at the end of this section.
PAGE 2
CONTENTS OF HARDWARE PACKS Please check your hardware packs against the illustrations below. The quantities for each item is listed in parenthesis.
PAGE 3
Assembly & Installation NOTE: References to left, right, front and rear of the tractor are from the operator’s position, unless otherwise stated. Install mounting bracket assembly on tractor as follows: • 1. Remove hitch bracket. 2. For ZT1 double bagger installation only: Place two washers (736-0242) between hitch bracket adapter (78902298) and the hitch bracket removed in Step 1.
PAGE 4
Install Hanger Assembly - Triple Bagger Model For model number 19A70056100, follow the steps below. 1. 2. Snap the front side of the chute support to the rail (2), as shown in Figure 4-8. 3. Attach the upper chute support to the chute deflector using the three (3) screws supplied in hardware pack 68902299. See Figure 4-9.
PAGE 5
7. Open hood by pushing in on the rear, right-side tab with your right hand (1), and lifting the cover with your left hand in the center rear of the bagger cover (2) as shown in Figure 4-13. 4. Pivot the discharge chute rearward until the hole in the discharge chute elbow aligns with the pin on the deck. Move the discharge elbow down onto that pin as shown in 3 of Figure 4-16. Secure the discharge chute elbow to the cutting deck using a wing knob (720-04122) included with the bagger kit.
PAGE 6
4. Insert the end of the discharge chute elbow (1) into the hole provided in the deck wheel mount as shown in the inset of Figure 4-19. 2 Figure 4-21 1 2. Figure 4-19 5. 6. Slide the chute tube over the chute elbow mounted on the cutting deck, as shown in Figure 4-22. Figure 4-23 2. Pivot the discharge chute rearward until the hole in the discharge chute elbow aligns with the pin on the deck adapter. Move the discharge elbow down onto that pin as shown in 2 of Figure 4-19.