Operator’s Manual Triple Bagger Kit Model 190-190-100 Model 190-192-190 IMPORTANT: Read safety rules and instructions carefully Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
TABLE OF CONTENTS Content Customer Support Important Safe Operation Practices Assembly & Operation Illustrated Parts List Warranty Page 2 3 7 10 Back Cover FINDING MODEL NUMBER This Operator’s Manual is an important part of your new Triple Bagger Accessory. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol—heed its warning.
26. Use only accessories and attachments approved for this machine by the machine manufacturer. Read, understand and follow all instructions provided with the accessory or attachment. 27. Data indicates that operators, age 60 years and above, are involved in a large percentage of tractor-related injuries. These operators should evaluate their ability to operate the tractor safely enough to protect themselves and others from serious injury. 28.
or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling. c. When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle. d. Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.
SECTION 2: LOOSE PARTS The grass catcher kit is shipped with following loose parts in the carton. Please remove all loose parts, including the hardware pack, from the carton before discarding it. Compare with Figure 1 to check that all parts were included. Note that the kit and the hardware pack contain extra items which are not used on your unit.
SECTION 3: ASSEMBLY & OPERATION NOTE: References to left, right , front and rear of the tractor are from the operator’s position, unless otherwise stated. • Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake. • For convenience, pivot the seat forward and leave it in that position until the grass collector is fully mounted and assembled.
• • • NOTE: An extra set of carriage bolt and lock nut have been supplied in your accessory kit. You may replace the old hardware for the chute stop bracket with these new ones, or save for later use. Remove the cutting deck from beneath the tractor (refer to instructions for Deck Removal in your tractor’s operator’s manual), then gently flip the deck over to expose its underside. Place a block of wood between the center deck housing baffle and the cutting blade to act as a stabilizer. See Figure 5.
• Insert chute tube here • Insert the lower end of the chute tube over the discharge chute so that its two notches fit into the two corresponding notches on the discharge chute. See Figure 9. Secure by placing the ends of the two short retainer straps on the discharge chute over the pins on the chute tube. See Figure 9. Operation Your triple bagger kit is a valuable accessory to your tractor. Optimize its performance by operating correctly.
SECTION 4: PARTS LIST FOR MODELS 190-190-100 & 190-192-190 14 23 21 26 4 12 22 20 7 31 28 16 33 3 16 16 8 17 11 30 18 19 16 25 B 8 B C 8 24 See parts break-down below 16 2 16 29 13 C 9 6 27 9 15 5 10 Components of Cover Assembly pn # 664-04018: 35 Components of Bag Assembly: 50 45 47 49 A 51 43 40 48 45 44 37 46 34 A 36 42 38 39 10 40
Model 190-190-100 & 190-192-190 Ref. No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. Part No. 17200A 17247 631-0221 664-04018 683-0617 689-00002 710-0597 710-0751 710-3008 710-3168 711-0309A 711-04069 712-0130 712-0431 712-3004A 712-3027 714-0117 723-04008A 726-3040 723-0476 731-0926B 731-2299A 736-0253 736-0270 736-3092 738-0380 Description Ref. No. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51.
MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. “Cub Cadet” warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship.
