Operator's Manual SERIES 1500 Hydrostatic Garden Tractor Model GT1554 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any), If a spark arrester is used, it should be maintained in effective working order by the operat
TABLEOFCONTENTS Content Important Safe Operation Practices Slope Gauge Tractor Set-up Know Your Garden Tractor Operating Your Garden Tractor Making Adjustments Maintaining Your Garden Tractor Service Page 3 7 8 9 12 16 18 24 Content Off-season Storage Maintenance Schedule Page 28 28 Maintenance Log Troubleshooting Attachments & Accessories 29 30 31 Specifications Replacement Parts Warranty Information 33 32 33 FINDINGMODELNUMBER This Operator's Manual is an important part of your new lawn tractor.
SECTION1: IMPORTANT SAFEOPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol--heed its warning.
23. Mufflerandenginebecomehotandcancausea burn.Donottouch. 24. Checkoverhead clearances carefullybeforedriving underlowhangingtreebranches,wires,door openingsetc.,wheretheoperatormaybestruckor pulledfromtheunit,whichcouldresultinserious injury. 25. Disengage allattachment clutches,depressthe brakepedalcompletely andshiftintoneutralbefore attempting to startengine. 26. Yourmachineisdesigned tocutnormalresidential grassofa heightnomorethan10".Donotattempt to mowthroughunusually tall,drygrass(e.g.
e. Useextremecarewhenapproaching blind corners,doorways, shrubs,treesor other objectsthatmayblockyourvisionofa child whomayrunintothemachine. f. Toavoidback-overaccidents,always disengagethecuttingblade(s)before shiftinginto reverse.The"Reverse CautionMode" should not be used when children or others are around. Keep children away from hot or running engines. They can suffer burns from a hot muffler. h. Remove key when machine is unattended to prevent unauthorized operation.
8. Nevertamperwiththesafetyinterlocksystemorother safetydevices.Checktheirproperoperationregularly. 9. Afterstrikinga foreignobject,stoptheengine, disconnect thesparkplugwire(s)andgroundagainst theengine.Thoroughly inspectthemachine forany damage.Repairthedamagebeforestartingand operating. 10. Neverattemptto makeadjustments or repairstothe machinewhiletheengineisrunning. 11. Grasscatchercomponents andthedischarge coverare subjecttowearanddamagewhichcouldexpose movingpartsorallowobjectstobethrown.
Sight and hold this levelwith a vertical tree... or a corner of a building... i _------ or a fence post | Sonts a 15o ! I.IJ I.IJ Q. 15° &i Z I.
SECTION3: TRACTOR SET-UP GasandOilFill-up The gasoline tank is located under the fender and has a capacity of three and-a-half gallons. Unthread the fuel cap by turning it counterclockwise. Use only clean, fresh (under 30 days old), unleaded gasoline. Fill tank to no more than four inches below the top of the filler neck to allow space for fuel expansion. Do not overfill. WARNING: Use extreme care / when handling gasoline. Gasoline is extremely flammable and the vapors are explosive.
SECTION4: KNOWYOURLAWNTRACTOR A ................. , H I J D K L E F M Figure 2 A Systems Indicator Monitor/Hour Meter B Throttle Control Lever H PTO (Blade Engage) Knob I Brake Pedal C Choke Control J D Parking Brake Lever K Cruise Control Lever E Seat Adjustment Lever L Deck Lift Lever F FueITank Cap M Cup Holder Drive Pedal G Ignition Switch Module NOTE: Any reference in this manual to the RIGHT or LEFT side of the tractor is observed from operator's position.
ThrottleControlLever The throttle control lever is located on the left side of the IgnitionSwitchModule Fast Position WARNING: Never leave a running machine unattended. Always disengage PTO, move shift lever into neutral position, set parking brake, stop engine and remove key to prevent unintended starting. tractor's dash panel. This lever controls the speed of the engine. When set in a given position, the throttle will maintain a uniform engine speed.
SystemsIndicatorMonitor/ HourMeter BATT. OIL DeckLiftLever Found on your tractor's right fender, the deck lift lever is used to change the height of the cutting deck. To use, move the lever to the left, then place in the notch best suited for your application. .J ......-.f ElectricPTO/ BladeEngageKnob 42.0 /// j 1/10 \\\ co) / jr HOURS To engage the power to the cutting deck or other (separately available) attachments, pull outward on the PTO/Blade PTO / BLADE Engage knob.
SECTION5: OPERATING YOURLAWNTRACTOR WARNING: AVOIDSERIOUS INJURYORDEATH • • • • • • • • GO UP AND DOWN SLOPES, NOT ACROSS. AVOID SUDDEN TURNS. DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIR IF MACHINE STOPS GOING UPHILL, STOP BLADE(S) AND BACK DOWNHILL SLOWLY. DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND. NEVER CARRY CHILDREN, EVEN WITH BLADES OFR LOOK DOWN AND BEHIND BEFORE AND WHILE BACKING. KEEP SAFETY DEVICES (GUARDS, SHIELDS, AND SWITCHES) IN PLACE AND WORKING.
Startingthe Engine DrivingTheTractor WARNING: interlock malfunctioning. WARNING: system Neveris operate the tractor ifThis the system was designed for your safety. _, WARNING: Refer to the TRACTOR SET-UPon page 8 of this manual for Gasoline and Oil fill-up instructions. Insert the tractor key into the ignition switch module. • Place the PTO (Blade Engage) knob in the disengaged (OFF) position. Engage the tractor's parking brake. Activate the choke control.
DrivingOnSlopes Usingthe DeckLiftLever Refer to the SLOPEGAUGE on page 7 to help determine slopes where you may operate the tractor safely. To raise the cutting deck, move the deck lift lever to the left, then place it in the notch best suited for your application. Refer to SettingTheCuttingHeightearlier in this section. slope in excess degrees (a rise ARNING: Do of not 15 mow on inclines with of a approximately 2-1/2 feet every 10 feet).
EngagingthePTO Mowing Engaging the PTO transfers power to the cutting deck or other (separately available) attachments. To engage the PTO, proceed as follows: • • • WARNING: To help avoid blade contact or a thrown object injury, keep bystanders, helpers, children and pets at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area. Move the throttle control lever to the FAST (rabbit) position. Pull the PTO/Blade Engage knob outward into the engaged (ON) position.
SECTION6: MAKINGADJUSTMENTS • adjustments engineto ismake running, WARNING: while Nevertheattempt any except where specified in the operator's manual. _, • LevelingtheDeck Check the tractor's tire pressure before performing any deck leveling adjustments. Refer to Tires on page 24 for information regarding tire pressure. If the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed.
ParkingBrakeAdjustment SteeringAdjustment If the tractor does not come to a complete stop when the brake pedal is completely depressed, or if the tractor's rear wheels can roll with the parking brake applied (and the hydrostatic relief valve open), the brake is in need of adjustment. See your Cub Cadet dealer to have the brake properly adjusted.
SECTION7: MAINTAININGYOURLAWNTRACTOR NOTE: Refer to MaintenanceCharton page 28 for a reference of recommended maintenance intervals. TEMPERATURE/ OiL ViSCOSiTYCHART ** WARNING: Before performing any maintenance or repairs, disengage PTO, set parking brake, stop engine and remove key to prevent unintended starting.
ChangingtheEngine011 The engine oil and oil filter should be changed after every 50 hours of tractor operation. Oil Fill Oap/ Dipstick WARNING: If the engine has been recently run, the engine, muffler and surrounding metal surfaces will be hot and can cause burns to the skin. Allow the tractor to cool and use caution when removing IMPORTANT:The oil filter should be changed at every oil change interval.
IMPORTANT:The oil fill cap/dipstick must be installed securely onto the tube at all times when the engine is operating. Severe engine damage could result from a failure to do so. • • • • • • Start the tractor engine and allow it to run for thirty seconds, then stop the engine and remove the ignition key. Check the oil level and add oil if necessary. Do not overfill the engine crankcase.
Feeler Gauge IMPORTANT:Make certain the tractor's discharge chute is directed AWAY from your house, garage, parked cars, etc. Spark Plug 2. 3. 4. Disengage the PTO (Blade Engage), set the parking brake and stop the engine. Thread the hose coupler (packaged with your tractor's Operator's Manual) onto the end of your garden hose. Attach the hose coupler to the water port on your decks surface. See Figure 14. \ ...................... \ Ground Electrode Gap Figure 13 Fuel Filter / / when engine is ho
Lubrication Carburetor NOTE: WARNING: Before lubricating, repairing, or inspecting, always disengage PTO, set parking brake, stop engine and remove key to prevent unintended starting. Carburetor adjustments should be made only after the engine has warmed up. The engines on Cub Cadet Series 1500 tractors are equipped with a fixed main jet carburetor. Engine Carburetors are equipped with a idle speed adjustment screw and a low idle fuel mixture screw.
Adjustment . NOTE: Engines may have a fixed idle or limiter cap on the idle fuel adjusting screw. Step 2 can only be performed within the limits allowed by the cap. . . Start the engine and run at half throttle for five to 10 minutes to warm up. The engine must be warm before performing steps 2 and 3. Low Idle Fuel Screw Setting: Place the throttle into the "idle" or "slow" position.
SECTION8: SERVICE Tires The blades may be removed as follows. • inflation pressureNever shownexceed on the sidewall of the WARNING: the maximum tire. • Remove the deck from beneath the tractor (refer to CuttingDeckRemovalon page 26), then gently flip the deck over to expose its underside. Place a block of wood between the center deck housing baffle and the cutting blade to act as a stabilizer. See Figure 17.
Charging Battery WARNING: Batteries give off an explosive gas while charging. Charge the battery in a well ventilated area and keep away from an open flame or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances. California Proposition 65 Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive after handling. harm.
• • • • Repeat the above steps on the tractor's right side. Move the deck lift lever into the top notch to raise the deck lift arms up and out of the way. Gently slide the cutting deck toward the front of the tractor allowing the hooks on the deck to release themselves from the deck stabilizer rod. Gently slide the cutting deck (from the right side) out from underneath the tractor.
0 0 0 1 27
SECTION9: OFF-SEASON STORAGE Clean and lubricate the tractor as instructed in Section7: To empty the system, run the engine until the tank and system are empty. MAINTAINING YOURLAWNTRACTORon page 18 of this manual before storing for an extended period. WARNING: Drain fuel only into an approved container outdoors, away from an open flame. Allow engine to cool. Extinguish cigarettes, cigars, pipes, and other sources of ignition prior to draining fuel.
SECTION11: MAINTENANCE LOG Please keep a record of the maintenance performed on your tractor.
SECTION12: TROUBLESHOOTING Trouble Possible Engine fails to start PTO/Blade Engage knob engaged. Parking brake not engaged. Spark plug wire(s) disconnected. Throttle control lever not in correct starting position. Choke not activated Fuel tank empty, or stale fuel. Blocked fuel line. Faulty spark plug. Engine flooded. Unit running with CHOKE activated. Spark plug wire(s) loose. Blocked fuel line or stale fuel. Engine runs erratic Corrective Cause(s) Vent in gas cap plugged.
SECTION13: ATTACHMENTS & ACCESSORIES The following attachments and accessories are compatible for Series 1500 Garden Tractors. See your Cub Cadet dealer or the retailer from which you purchased your tractor for information regarding price and availability. Attachments 19A-102 16 cu. ft. Steel Tow Cart 19A-103 42" Tow-Behind Sweeper 19A-104 25 gal. Tow-Behind Sprayer 19A-105 Tow-Behind Broadcast Spreader 19A-106 10 cu. ft.
SECTION14: REPLACEMENT PARTS NOTE: Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number ready). Parts Manual downloads are also available free of charge at www.cubcadet.com.
SECTION15: SPECIFICATIONS* GT1554 Capacities Fuel Tank 3.5 gal. (13.2 liters) Engine Crankcase (w/filter) Transmission 57.5 oz. (1.7 liters) 76 oz. (2.25 liters) Hydrostatic Transmission Make Hydro-Gear Gear Ratio 22.2:1 Forward Speed 0 m.p.h. - 5.2 m.p.h. Reverse Speed 0 m.p.h. - 2.3 m.p.h. Engine (Air-cooled, 4-cycle) Make Kohler Courage Model SV740 Cylinders Twin Bore 3.27 in. (83 mm) Stroke 2.64 in. (67 mm) Displacement 44.2 cubic in. (725 cc) Power @3600 RPM 25 HP (18.
CALiFORNiA EMiSSiON CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLiGATiONS The CaliforniaAir ResourcesBoardandMTDConsumerGroupInc are pleasedto explainthe evaporativeemissioncontrolsystemwarrantyon your 2006 lawn mower.In California,new lawnmower mustbe designed,builtand equippedto meetthe State'sstringentanti-smogstandards.MTDConsumerGroupInc must warrantthe EECSon your lawnmowerfor the periodof time listed below providedthere has been no abuse, neglector impropermaintenanceof your lawnmower.
FEDERAL AND KOHLER CO. CALIFORNIA EMISSION CONTROL SYSTEMS LIMITED WARRANTY UTILITY AND LAWN AND GARDEN ENGINES The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Kohler Co. are pleased to explain the Federal and California Emission Control Systems Warranty on your small off-road equipment engine. For California, engines produced in 1995 and later must be designed, built and equipped to meet the state's stringent anti-smog standards.
CUB CADET LLC MANUFACTURER'S LiMiTED WARRANTY FOR SERIES 1000 & SERIES 1500 TRACTORS IMPORTANT: Toobtainwarrantycoverageownermust presentan original proofof purchaseand applicablemaintenancerecordsto the servicingdealer. Pleaseseethe operator'smanualfor informationon requiredmaintenanceand serviceintervals.
Manual del Operador SERIE 1500 Tractor corta cesped hidrostatico Modelo GT1554 IMPORTANTE: LEA CON ATENCION LAS REGLAS DE SEGURIDAD Y LAS INSTRUCCIONES Advertencia: Esta unidad esta equipada con un motor de combustiCn interna y no debe utilizarse en o cerca de un terreno agreste cubierto de bosque, malezas o pasto a menos que el sistema de escape del motor venga equipado con un amortiguador de chispas que cumpla con las leyes locales o estatales vigentes (en caso de existir).
iNDICE |ndice P_gina Medidas importantes de seguridad Indicador de pendiente Montaje del tractor Conozca su tractor corta cesped Funcionamiento del tractor corta 3 7 8 9 12 cesped Realizaci6n de ajustes Mantenimiento del tractor corta cesped Servicio 17 19 25 |ndice Almacenamiento fuera de temporada Calendario de mantenimiento P_gina 29 29 Registro de mantenimiento Soluci6n de problemas Aditamentos y accesorios Especificaciones Piezas de reemplazo Informaci6n sobre la garanfia 30 31 32 34 33 37 BU
SECCIONI:MEDIDASIMPORTANTES DESEGURIDAD ADVERTENClA: La presencia de este s[mbolo indica que se trata de instrucciones importantes de seguridad que debe respetar para evitar poner en riesgo su seguridad personal y/o material y la de otras personas. Lea y siga todas las instrucciones en este manual antes de iniciar la operaci6n de esta ma.quina. En caso de no seguir estas instrucciones podria provocar lesiones personales. Cuando vea este simbolo--siga la advertencia. PELIGRO: Esta ma.
23. Elsilenciador y elmotorsecalientan y pueden 5. Tenga especial cuidado con los colectores de producirquemaduras. Nolostoque. recorte de cesped u otros accesorios. Los mismos 24. Reviseelespaciolibreporencimadelacabeza pueden modificar la estabilidad de la ma.quina. antesdeconducir bajolasramasbajasde_.rboles, 6. Haga que todos los movimientos en las pendientes cables,cerramientos depuertas,etc.enloscuales sean lentos y graduales.
9. antes de colocar marcha atrbs. El "Modo Precauci6n Marcha Atrbs" no debe utilizarse ante la presencia de nihos u otras personas. g. Mantenga a los ni_os alejados de los motores en marcha o calientes. Pueden sufrir quemaduras con un silenciador caliente. h. Retire la Ilave cuando deje la ma.quina sin vigilancia, para impedir que una persona sin autorizaci6n la maneje. Nunca permita que los niSos menores de 14 aSos operen esta ma.quina.
8. Nuncaintenteviolarelsistemadebloqueode todosloscomponentes yreempla.celos s61o conpiezas seguridad u otrosmecanismos deseguridad. Controle de losfabricantes deequiposoriginalesenumeradas peri6dicamente quefuncionen deformaadecuada. enestemanual."Lautilizaci6n depiezasqueno 9. Despues degolpearcontraalgt_nobjetoextraBo, cumplanconlasespecificaciones deequiposoriginales detengael motor,desconecte el cabledelabuj[ay podr[atenetcomoresultado unrendimiento incorrecto, conecteelmotora masa.
Mire y mantengaestenivelconun _rbol vertical... I_- o la esquinade unedificio... I I | I | I Oob/ep I I °r/a/i.oo _ _ i 'l PUnteatla(represent IJJ z IJJ i r-_ z I.IJ Q_ I.IJ r-_ r-_ i r-_ z i z i r_ r_ I.
SECCION3:MONTAJEDELTRACTOR ADVERTENClA: Llenadodegasolinay aceite El tanque de gasolina esta. ubicado debajo del guardabarros, y posee una capacidad de tres galones y medio. Quite la tapa de combustible girando en sentido contrario de las agujas del reloj. Utilice Onicamente gasolina limpia, nueva (no ma.s de 30 d_as de uso) y sin plomo. Llene el tanque sin pasar las cuatro pulgadas por debajo de la parte superior del cuello de Ilenado para dejar espacio para la expansi6n del combustible.
SECCION4:CONOZCA SUTRACTOR CORTAClaSPED A H I J D K L Figura 2 A Monitor indicador de sistemas/medidor horario B Palanca de control del regulador C Control del cebador H Perilla de potencia de arranque (PTO) (enganche de cuchilla I Pedal de freno J Pedal de la transmision D Palanca de freno de mano K Palanca de control de crucero E Palanca de ajuste del asiento L Palanca de elevaci6n de la plataforma M Portacubeta F Tap6n del dep6sito de combustible G M6dulo del interruptor de encendido NOTA:
Palancadecontroldel regulador La palanca de control del regulador esta. ubicada del lado izquierdo del panel de instrumentos del tractor. Esta palanca controla la velocidad del motor. Cuando se Io coloca en una posici6n determinada, el regulador mantiene una velocidad de motor uniforme. IMPORTANTE: Cuando opere el tractor con la plataforma de corte colocada, asegt_rese de que la palanca del regulador este siempre en la posici6n FAST (ra.pido; representado por una liebre).
Monitor indicador desistemas/medidor horario Potenciade arranque (PTO)el ctrica/ BATT. OIL Perilla deenganchede cuchilla .J Para conectar la energ_a a la plataforma de corte u otros accesorios (disponibles por separado), tire de la perilla PTO/ enganche de cuchilla. Presione la perilla PTO/enganche de cuchilla para desconectar la energ[a de la plataforma de corte u otros accesorios (disponibles por separado). ......--J 42.0 /// j j_ HOURS 1/10 \\\ co) / PTO / BLADE ! NOTA: AI encender el moto
SECCION5:FUNCIONAMIENTO DESUTRACTOR CORTAC#SPED ADVERTENClA: Tenga mucho cuidado cuando opere el tractor enMODO DE PRECAUOION EN MAROHA ATR.&.S. Mire siempre hacia abajo y hacia atra.s antes y mientras opera marcha atra.s. No opere el tractor cuando haya niSos u otras personas en el lugar. Detenga el tractor inmediatamente si alguien ingresa en la zona.
• Si las ruedas de calibraci6n tienen excesivo espacio libre respecto de la superficie inferior, afloje las ruedas hasta el orificio de posicionamiento que proporciona aproximadamente Y2pulgada de espacio libre segt_n se describi6 mas arriba. Consulte la secci6nNivelaci6n dela plataf0rmaen la pa.gina 17 de este manual para obtener instrucciones detalladas sobre diferentes ajustes de la plataforma.
Colocaci6ndelfrenodemano transmisi6n con la bola de su pie (NO su tal6n) hasta que se alcance la velocidad deseada. Yea la Figura 6. IMPORTANTE: NO intente cambiar la direcci6n de desplazamiento mientras el tractor este en movimiento. Siempre Ileve el tractor a una parada completa antes de girar el pedal de transmisi6n desde la posici6n de avance a la de marcha atra.s y viceversa.
• • • Presione el pedal del freno para soltar el control de crucero y detener el tractor. Presione ligeramente el pedal de la transmisi6n. afuera, luego hacia arriba para trabarla en su lugar. NOTA: La transmisiSn NO se enganchara cuando la varilla de derivaciSn hidrostatica se tire hacia fuera. Para cambiar a marcha atra.s al operar con control de crucero, presione el pedal del freno para desactivar el control de crucero y hacer que el tractor se detenga por completo.
• Cortedec6sped ADVERTENClA: Para ayudar a evitar el contacto con las cuchillas o una lesi6n por algun objeto que sea arrojado, mantenga a las personas que Io observan, a los ayudantes, niSos y mascotas alejados al menos 25 metros de la ma.quina mientras esta. en funcionamiento. Detenga la ma.quina si alguien entra en la zona. • Este tractor esta. equipado con una de las plataformas de corte de alta calidad de Cub Cadet. La siguiente informaci6n sera.
SECCION6:REALIZACION DEAJUSTES • Apriete el frente de las tuercas hexagonales interiores contra la mensula de suspensi6n frontal para elevar el frente de la plataforma; afloje las tuercas hexagonales para bajar el frente de la plataforma. Vea Figura 9. • Vuelva a apretar las dos tuercas de sujeci6n contra las tuercas hexagonales interiores cuando alcance el ajuste adecuado.
Ajustedelfrenodemano Si el tractor no se detiene por completo cuando se presiona totalmente el pedal de freno, o si las ruedas traseras del tractor siguen rodando con el freno de mano colocado (y la va.lvula de descarga hidrosta.tica abierta) el freno necesita ajustes. Consulte con su distribuidor Cub Cadet para realizar un ajuste correcto del freno. Ajustedelasiento _, tractor, asegt_rese que asiento ADVERTENClA: Antesel de operar este el enganchado en el tope del asiento, pa.rese detra.s de la ma.
SECCION7:MANTENIMIENTO DESUTRACTOR CORTAClaSPED NOTA: Consulte Tabla de Mantenimientoen la pagina 29 para referencia futura de los intervalos de mantenimiento recomendados. _, TEMPERATURE / 01L VISCOSITY CHART ** de mantenimiento o reparaciones, desconecte ADVERTENClA: realizar eltareas la potencia de arranque Antes (PTO),decoloque freno de mano, apague el motor y retire la Ilave, para evitar que alguien encienda accidentalmente el motor.
Cambiodeaceitedel motor El aceite del motor y el filtro de aceite deben cambiarse despues de cada 50 horas de funcionamiento del tractor. Tap6ndelie Varillade en funcionamiento recientemente, el motor, DVERTENCIA: el motor se ha puesto silenciador y las Sisuperficies metalicas circundantes estaran calientes y pueden causar quemaduras a la piel. Deje que el tractor se enfrie y sea muy cauteloso al extraer Io necesario.
IMPORTANTE: El tap6n de Ilenado de aceite/varilla de medici6n de nivel de aceite deben instalarse firmemente dentro del tubo en todo momento cuando el motor est_ funcionando. El motor podria resultar con daSos graves de no proceder as_. • • • • • • Ponga en marcha el motor del tractor y dejelo funcionar por treinta segundos, luego detengalo y extraiga la Ilave de encendido. Verifique el nivel del aceite y agregue mAs de set necesario. No Ilene en exceso el carter del motor.
Calibradorde separaciones IMPORTANTE:Asegt_rese de que el canal de descarga del tractor NO ESTE_ORIENTADO EN LA DIRECCION Bujiade encendido en que se encuentran la casa, el garaje, los veh_culos estacionados, etc. 2. Desconecte la potencia de arranque (enganche de cuchilla), coloque el freno de mano y detenga el motor. 3. Enrosque el acople de manguera (embalado con el Manual del Operador de su tractor) en el extremo de la manguera de jardin.
Lubricaci6n Los motores de los tractores Serie 1000 de Cub Cadet vienen equipados con un carburador de inyecci6n principal fijo. de mantenimiento, Antes reparaciones ADVERTENClA: de realizar tareaso inspecciones, desconecte la potencia de arranque (PTO), coloque el freno de mano, apague el motor y retire la Ilave, para evitar que alguien encienda accidentalmente el motor. _, Los carburadores esta.
Ranuras , NOTA: Los motores tienen una polea fija o tapdn limitador en el tornillo de regulacidn de combustible en ralentL El paso 2 solamente se puede Ilevar a cabo dentro de los Ifmites permitidos por el tapdn. , , Arranque el motor y dejelo en marcha a potencia intermedia por Io menos 10 minutos para calentarlo. El motor debe estar caliente antes de Ajuste de velocidad en ralenti baja: Coloque el control del regulador en la posici6n "ralenti" o "lenta".
SECCION8:MANTENIMIENTO Neum ticos _, decorteen la pa.gina 26); luego voltee con delicadeza la plataforma para dejar al descubierto su parte inferior. Coloque un bloque de madera entre el deflector del alojamiento central de la plataforma y la cuchilla de code, para que active como estabilizador. Vea la Figura 18. presi6n ma.xima de inflado que se indica en ADVERTENClA: Nunca exceda la los laterales de los neuma.ticos. La presi6n de neuma.
Bateria cargador de la bateria antes de cargar la bateria de su tractor. Siempre siga las instrucciones y tenga en cuenta las advertencias. Los barnes de la bateria y los accesorios afines, Advertencia, Proposicibn 65 de California: contienen plomo y compuestos de plomo, sustancias quimicas que segt_n Io establecido par el Estado de California causan cancer y daSos en el sistema reproductivo. L_tvese las manos despues de estar en contacto con estos componentes.
Cambiode la correadetransmisi6n NOTA: Es necesario retirar varios componentes y herramientas especiales (es decir, Ilave de impacto/ aire) para cambiar la correa de transmisidn del tractor. Solicite a su distribuidor de Cub Cadet que le realice el reemplazo de la correa. P01ea10ca Transmisi6nhidrost tica Mantenga el Area alrededor del ventilador de enfriamiento de la transmisi6n libre de pasto y residuos en todo momento. La transmisi6n hidrosta.tica viene sellada de fa.
0 O 28
SECCION9:ALMACENAMIENTO FUERADEESTACION estabilizado. Limpie y lubrique el tractor tal como se indica en la SecciCn 7: MANTENIMIENTO DESUTRACTOR CORTAClaSPED Para vaciar el sistema, deje que el motor funcione hasta que el dep6sito y el sistema esten vacios. en la pa.gina 19 de este manual antes de almacenar la unidad por un periodo extenso. ADVERTENClA: Drene el combustible t_nicamente dentro de un recipiente aprobado y en un lugar al aire libre, lejos de cualquier llama expuesta.
SECCION11: REGISTRO DEMANTENIMIENTO Lleve un registro del mantenimiento realizado a su tractor.
SECCION12:SOLUCIONDE PROBLEMAS Problema Causa(s) El motor no arranca Perilla de potencia de arranque (PTO) (enganche de cuchilla) conectada. No esta colocado el freno de mano. Se ha desconectado el cable de la bujia. La palanca de control del regulador no esta en la posici6n de arranque correcta. No se ha activado la obturaci6n El dep6sito de combustible esta vacio o el combustible se ha echado a perder. La linea del combustible esta bloqueada. La bujia no funciona correctamente. Motor inundado.
SECCION13: ADITAMENTOS Y ACCESORIOS Los siguientes aditamentos y accesorios son compatibles con los Tractores Corta C_sped de la Serie 1500. Consulte con su distribuidor Cub Cadeto con el representante al cual le ha comprado el tractor para obtener ma.s informaci6n con respecto a precios y disponibilidad. NOTA: Los Tractores Corta Cesped Modelo Serie 1500 NO han sido dise#ados para ser utilizados con accesorios que penetran en el suelo (como, por ejemplo, cultivadoras o arados).
SECCION14: PIEZASDE REEMPLAZO NOTA: Llame por telefono al (800) 965-4CUB para solicitar piezas de reemplazo o un Manual de Piezas de Repuesto completo (tenga el nt_mero de modelo y nt_mero de serie de su tractor a mano). En tambien podra, descargar el Manual de Piezas de Repuesto sin cargo alguno.
SECCION15: ESPECIFICACIONES* GT1554 Capacidades Dep6sito de combustible 3,5 galones (13,2 litros) CArter del motor (con filtro) 57,5 onzas. (1,7 litros) Transmisi6n 76 onzas (2,25 litros) Transmisi6nhidrost_tica Marca y modelo Hydro-Gear Engranaje 22.2:1 reductor Velocidad de avance 0 m.p.h. - 5,2 m.p.h. Velocidad marcha atras 0 m.p.h. - 2,3 m.p.h. Motor (Refrigerado por aire, 4 ciclos) Marca Kohler Courage Modelo SV740 Cilindros Dobles Diametro interior 3,27 pulg.
NOTAS 35
NOTAS 36
DECLARACION DEGARANT|A DELCONTROL DERECHOS Y OBLIGACIONES DE LAS EMISIONES DE CALIFORNIA DE SU GARANT|A El Consejode RecursosAereosde Californiay MTDConsumerGroupInc.se complacenen explicarla garanfiadelsistemade controlde emisionesporevaporaci6n de su cortadorade cesped2007.En California,las nuevasmaquinaspara cortarcespedsedebendisefiar,construiry equiparde modode cumplircon las rigurosas normasdelestadocontralapoluci6n.MTDConsumerGroupInc.
KOHLER CO. SIS.TEMAS DE CONTROL DE EMISIONES FEDER.ALES Y DE CAL.IFORNIA GARANTIA LIMITADA MOTORES DE USO GENERAL, CESPED Y JARDIN La Agencia de Protecci6n Ambiental de los Estados Undios (EPA), la Administraci6n de los Recursos del Aire de California (CARB) y Kohler Co. se complacen en explicar la Garantia de los Sistemas de Control de Emisiones Federales y de California de su nuevo motor pequeSo para equipo todo terreno.
CUB CADET LLC GARANTIA LIMITADADEL FABRICANTEPARATRACTORES DE SERIE 1000 Y SERIE 1500 IMPORTANTE:Paraobtenercoberturade garantia,el propietariodebe presentarunaevidenciaoriginalde lacompray losregistrosde mantenimiento correspondientesal centrode serviciotecnicoautorizadodel distribuidor. Consulteel manualdel operadorparaobtenerinformaci6n sobrelosintervalos de mantenimientoy servicio requeridos. EnCanada: ContacteMTD ProductsLimited,Kitchener,ON N2G4J1, Ilameal 1-800-6681238o visite nuestrositioweben www.
CUBCADET LLC, P.O.