888385_01 Install.
888385_01 Install.
888385_01 Install.book Page i Wednesday, November 11, 1998 2:45 PM Safety Installation Instructions Please Read Carefully WARNING: To avoid electrical shock hazard to personnel or equipment damage observe the following precautions when installing telephone equipment: 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3.
888385_01 Install.book Page ii Wednesday, November 11, 1998 2:45 PM For equipment with external mains power adapters: CAUTION: Intended for use in a protected environment. Use only a Nortel supplied or recommended mains power adapter marked as indicated below: Mains Supply (Input Voltage) Output Voltage Rated Current Approval Markings 240 Vac 9 Vdc 0.6 A maximum CLASS II POWER SUPPLY - VE +VE 230 Vac 9 Vdc 0.6 A maximum CLASS II POWER SUPPLY - VE +VE 110 Vac 9 Vdc 0.
888385_01 Install.book Page iii Wednesday, November 11, 1998 2:45 PM Important Safety Instructions Please Read Carefully When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury of persons, including the following: 1. Read and understand all instructions. 2. Follow the warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning.
888385_01 Install.book Page iv Wednesday, November 11, 1998 2:45 PM Canadian Regulations Refer to the System Installation Guide for regulatory information. Note: This equipment may only be connected to the Host equipment (Norstar or Companion equipment) and may not be connected directly to the Public Switched Telephone Network (PSTN). This device complies with Part 68 and Part 15 of the FCC Rules and ICES-003 Canadian EMI requirements.
888385_01 Install.book Page v Wednesday, November 11, 1998 2:45 PM US Regulations Federal Communication Commission (FCC) Notice FCC registration number: This telephone equipment complies with Part 68, Rules and Regulations, of the FCC for connection to Host equipment (Norstar or Companion equipment) and may not be connected directly to the Public Switched Telephone Network (PSTN). (The FCC registration number appears on a sticker affixed to the bottom of the unit.
88385_01 Install.book Page vi Wednesday, November 11, 1998 2:45 PM US Regulations continued EMI/EMC (FCC Part 15) Note: This device complies with Class A EMI requirements when connected to host equipment that meets Class A and Class B when connected to host equipment that meets Class B. Consult the System Installation Guide for the applicable compliance.
888385_01 Install.book Page 1 Wednesday, November 11, 1998 2:45 PM Introduction Installing the Station Message Detail Recording 6 (SMDR6) involves five steps: 1. Mounting the SMDR6 unit on the wall. 2. Connecting the unit to an available station port on the Key Service Unit (KSU). 3. Connecting the unit to the printer. 4. Connecting the power adapter to the SMDR6 and power outlet. 5. Testing the unit. This guide provides the steps necessary for installing SMDR6.
888385_01 Install.book Page 2 Wednesday, November 11, 1998 2:45 PM Parts checklist Mounting the unit To install the SMDR6 unit, make sure you have: ❏ DB25 serial connector (provided) ❏ Key Service Unit ❏ Serial Printer ❏ DB25 Serial Cable (max 8 m/ 25 ft) Note: We recommend a shielded RS-232 cable. ❏ 9 Vdc Power Supply (provided) ❏ Two #8 screws (for wall mounting) ❏ Screwdriver ❏ Paper wall mount plate (provided) The SMDR6 unit must be installed within 800 m (2,660 ft) of the KSU.
888385_01 Install.book Page 3 Wednesday, November 11, 1998 2:45 PM 6. Attach the DB25 serial cable to the RS-232 port of the SMDR6 unit by tightening the thumb screws. 7. Connect the SMDR6 unit’s line jack (next to the DB-25 connector) using a line cord to any unused station port on the KSU. ~ Terminal (to phone) Line (to KSU) DB-25 9 V DC LED 8. Plug the power supply into the SMDR6 unit. 9. Plug the power supply adapter into a standard AC outlet.
888385_01 Install.book Page 4 Wednesday, November 11, 1998 2:45 PM Setting the printer Before you connect the printer, make sure the printer is set at: 1. speed: 1200 to 115200 bits per second 2. 8 bits per character 3. no parity 4. no XON, XOFF 5. 1 start bit 6. 1 stop bit Note: The printer used for SMDR6 can be any RS-232 serial compatible device such as a serial printer, PC with communication software or call accounting package with the capability to collect data from the serial port.
888385_01 Install.book Page 5 Wednesday, November 11, 1998 2:45 PM Testing SMDR6 Test SMDR6 by dialing the Administration Feature Code from any Norstar telephone. 1. Press ƒ·•¤ SMDR6 Admin NEXT . The display shows: QUIT Note: On M7100/M7208 telephones, the second line of the display is not shown. 2. Troubleshooting Press QUIT or ® . Problem: SMDR6 Interface Unit will not respond to Feature Code. Note: Refer to the SMDR6 System Coordinator Guide for programming information.
888385_01 Install.
888385_01 Install.
888385_01 Install.book Page 2 Wednesday, November 11, 1998 2:45 PM 1-800-4NORTEL http: / / www.nortel.com/norstar Norstar is a Trademark of Northern Telecom.
