GEOPOINT BOX P E R S O N A L T R A C K E R User Manual
GEOPOINT BOX P E R S O N A L T R A C K E R User Manual July Edition 2009
Limitation of Liability The Manufacturer reserves the right to modify the devices or the device specifications in this manual without prior notice. Any copy of this manual, in part or in full, whether by photocopy or by other means, even of electronic nature, without the manufacture giving written authorisation, breaches the terms of copyright and is liable to prosecution.
Contents Safety Instructions ................................................................................................................. 5 Environment ................................................................................................................... 7 RECYCLING THE PRODUCT AND ITS RELEVANT ACCESSORIES ................................................. 7 Medical Appliances .......................................................................................................
Use of the Functions ........................................................................................................... 26 SOS Key....................................................................................................................... 27 Position Request .......................................................................................................... 28 Automatic Position Sending .........................................................................................
Safety Instructions Safety Instructions Please read the following safety instructions carefully. Not following them may be dangerous and/or illegal. Please read carefully the user manual for further details. SWITCHING ON IN SAFE ENVIRONMENTS Do not switch the device on when prohibited or whenever it could cause any interference or danger. ROAD SAFETY Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.
Safety Instructions SWITCH OFF NEAR BLASTING Follow any restrictions. Do not use the device where blasting is in progress. USE THE DEVICE SENSIBLY Do not use the device for any uses other than those it has been built for. Keep to the instructions as explained in the product manual. QUALIFIED SERVICE Only qualified personnel may install or repair this product. ACCESSORIES AND BATTERIES Use only approved accessories and batteries. Do not use incompatible products.
Safety Instructions Environment Always switch off the device in areas where it is prohibited, or whenever it could cause interference or danger. Always observe the specific local rules and standards. Use the device in its normal operating position only. The device complies with the laws for exposure to radio-frequencies when used in the normal position or when positioned at least 2.2 cm (7/8 inches) away from the body.
Safety Instructions Pacemaker A minimum distance of 15.3 cm (6 inches) between the device and a pacemaker is recommended in order to avoid interference with the medical appliance. In the event of pacemaker wearers, please observe the following precautions: • always keep the device more than 15.3 cm (6 inches) away from the pacemaker • never keep the device in close contact with the body (e.g.
Safety Instructions Potentially Explosive Environments Switch off your device in any area with a potentially explosive atmosphere, (e.g. where you would be normally advised to turn-off your vehicle engine) and obey all signs and instructions in that area. Switch off the device near refuelling points and at service stations.
General Information General Information This chapter contains general information on the tracker and its relevant accessories. WARNING: The GPS receiver and the GSM device work at higher radio frequencies which can be stopped by enclosures containing metal and plastic parts. It is suggested to keep the tracker under light clothes, as external as possible. Examples of shielding materials: kevlar, carbon fibre, some polyurethanic and polyamidic resins especially if black, etc.
General Information The tracker is a portable device able to transmit its geographical location to a mobile phone or PC in real-time. Moreover, the detected data can be recorded for further analysis. The tracker is available in two different version: • LCD: GPS tracker with display, phone and 2MB data memory. • BOX: GPS tracker without display, without vocal communication and 512kB data memory.
General Information The tracker can be used as a system for: • locating elderly people, children, or anyone in difficulty, or with health problems or cognitive disorders, etc. • locating, during outdoor individual sports activities (e.g. mountaineering, trekking, parachuting,...) • locating and finding lost pets • locating groups of people (e.g. park guards, local police forces, emergency teams,...) • locating small boats • GPS anti-theft system for vehicles, motorcycles, goods,...
General Information ON/OFF BUZZER YELLOW LED (GPS) GREEN LED (GSM) RED LED (BATTERY) SOS KEY USB DC IN 13
General Information Package Contents Available accessories: • No. 1 USB cable • No. 1 (2 in case of KIT) European battery charger - American battery charger available on request • No. 1 (2 in case of KIT) Li-ion battery • No. 1 CD ROM for MyTrack software installation, for tracker management and personal tracking • No. 1 (2 in case of KIT) User Guide of the tracker Use only accessories, batteries and battery chargers approved by the Manufacturer.
General Information Network Services In order to use some tracker functions, such as sending and/or receiving SMS messages, data communication, GPRS, etc., it is necessary to get access through the network service provider. GSM / GPRS Network The GSM network (Global System for Mobile Communications) is a data transmission system available from the network service provider. For further information about availability, services and relevant costs of SIM cards, please contact the network provider.
General Information To communicate with the tracker through a PC in GPRS network, check if a firewall is installed, and allow the access to the port which will be used for the communication. This procedure must be carried out only by people which have the proper technical features. If Windows Firewall is enabled, during the communication GPRS access the following window is displayed. Keep Blocking The access to the port is stopped. It is not allowed to communicate in GPRS network.
General Information If the GPS receiver reports that a three dimensional satellite FIX is available (3D FIX), it means that the signal is optimal. In some climatic or structural conditions, (when it is foggy, clouded, ... or inside buildings, tunnels, ...) partial or total GPS signal coverage may be missing. In this case, some functions may not be available.
Preliminary Procedures Preliminary Procedures This chapter contains all the information on the preliminary procedures relevant to the tracker use. Inserting the SIM Card and Battery The SIM card allows to receive and transmit data and calls by means of the GSM network. Pay attention when choosing the contract type to make with the SIM card provider, since it could affect the tracker communication functions.
Preliminary Procedures WARNING: After SIM card insertion, any SMS message which will be received, it will be erased. WARNING: Before proceeding with any insertion/removal of the SIM card, switch off the tracker, disconnect the battery charger and/or the USB cable. To insert/remove the SIM card or the battery, proceed as follows. 1. Remove the back cover from the tracker by pressing down on the small flap and lifting upwards (Pict. 1). Pict. 1 2. Remove the battery by lifting it out (Pict. 2). Pict.
Preliminary Procedures 3. Insert the SIM card by leading it into the appropriate housing; check if it has been inserted correctly, with the golden contact area facing downwards (Pict. 3). Pict. 3 4. Insert the battery paying attention to coincide the contact area with that of the tracker. Close the tracker by replacing the back cover (Pict. 4). Pict. 4 WARNING: Insertion/removal of the SIM card must be carried out with extreme care, to avoid damaging the tracker, battery or SIM card.
Preliminary Procedures How to Charge the Battery Before using the tracker for the first time, the battery must be completely charged. Before charging, check that the network electrical supply corresponds to that of the battery charger. Do not exceed the network voltage indicated on the battery charger. To charge the battery: 1. Plug the provided battery charger into the electrical supply socket. 2. Connect the battery charger cable to the appropriate tracker connector. 3.
Preliminary Procedures Battery Life The tracker battery life changes according to the environment conditions and its activity. The following table shows the battery life in several conditions. STATUS TIME Standby mode with motion sensor active. ~10 days Tracking SMS every minute (GPS always on). ~9 hours Tracking SMS every 5 minutes (GPS with hotstart). ~4 days Continuous tracking. ~2 hours Data connection mode, with GPS system continuously active. ~2 hours Position data recording every minute.
Preliminary Procedures Information on the Battery A new battery reaches maximum performance only after being completely charged and discharged 2 or 3 times. The battery can be charged and discharged several times, but will eventually wear out with use. A completely charged battery can discharge itself even when left unused. When the tracker loses the performance quality, it is necessary to replace the battery.
Preliminary Procedures Power On and Off To switch the tracker on/off, press the key situated in the upper part of the device for 2 seconds. At tracker switching on/off, the 3 LEDs will light up together at the same time for 1 second and an acoustic signal will be emitted. WARNING: Do not switch on the tracker when its use is prohibited or when it may cause interference or danger (refer to the chapter Safety Instructions).
Preliminary Procedures LED indicators Identification symbols Yellow LED - GPS signal status • OFF T tracker off or GPS receiver switched off • ON T waiting GPS • blinks every second T poor signal level (2D FIX) • blinks every 4 seconds T high signal level (3D FIX) Green LED - GSM network status • OFF T tracker off or connected to the USB port • blinks every second T network search in progress • blinks every 4 seconds T sufficient signal strength • 2 blinks every 4 seconds T GSM/GPRS data communication in
Use of the Functions Use of the Functions Tracker Function Description Refer to SOS key the tracker sends an alarm message section SOS Key Position Request the tracker sends an SMS containing its position to the phone number which requested this data section Position Request Automatic Position Sending the tracker sends automatically its position by SMS or by GPRS connection section Automatic Position Sending Position Data Recording the tracker records its position data to review the track afte
Use of the Functions The tracker can work without the SIM card. In this case, all functions operating with GSM/GPRS network will not be available.
Use of the Functions NOTE: When there is no GSM signal, the alarm functions may not be available. Example of the SMS message displayed on the mobile phone, with the detected current position data GEO,ID:GLORIA,SOS ALARM,POS:45g37.9480N,008g28.9992E,ALT:0218m,07/04/10,10:09 Example of the SMS message displayed on the mobile phone, with the last position data detected before the GPS signal loss GEO,ID:GLORIA,SOS ALARM,LAST POS:45g37.9480N,008g28.
Use of the Functions Programming To use this function, it is necessary to send to the tracker an SMS command by a mobile phone or by a GSM device and waiting for the reply. 1) Tracker position request in realtime Sending an SMS command (rpos) Automatic Position Sending The tracker can send its own position at a programmable rate.
Use of the Functions CYCLIC GPRS CONNECTION The cyclic GPRS connection allows to connect the tracker automatically at a programmed rate for the continuous position updating. At the programmed rate, the tracker will be connected only for the time needed for sending the position point. This function is very useful if combined with the I-Scout web server as it allows to display the detected positions by every station connected to internet.
Use of the Functions The following list shows all the events which can be detected and recorded automatically by the tracker.
Use of the Functions All position data contained in the tracker memory can be erased. 1) Erase the recorded position data Sending an SMS command (wem) Using the provided software WARNING: The Erase function deletes all GPS data contained in the tracker memory. Once deleted, the data is no longer retrievable. Geofence The Geofence function allows to monitor the tracker entry and exit in a pre-established area. This is a rectangular area and can be programmed setting the area diagonal coordinates.
Use of the Functions Example of the SMS message displayed on the mobile phone, when the tracker exits the area GEO,ID:GLORIA,GEOFENCE EXIT,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09 The SMS message structure of the Geofence function is described here below: GEO ID:−−−−−− GEOFENCE ENTER POS:−−−−−.−−−−−,−−−−−.−−−−− ALT:−−−−.− −−/−−/−−,−−:−− Tracker type. Tracker name preset by the user through the provided software. Alarm message. Latitude and longitude of the geographical position.
Use of the Functions Programming To use this function, it is necessary to set the phone number where the alarm messages will be sent, defined the circle centre and then set the radius.
Use of the Functions Power Save Mode The Power Save Mode allows for optimal management of the tracker battery. It is possible to set the tracker automatic switching on/off according to specific use requirements. NOTE: It is not possible to enable more than one Power save mode simultaneously. NOTE: When the tracker is switched off in Power save mode, an SOS message can be sent pressing the relevant red key for at least 2 seconds.
Use of the Functions Programming To use this function, it is necessary to set the parameters relevant to one power save mode. 1. MOTION MODE 1) Set the motion sensor parameters (sensitivity, timeout) Using the provided software 2) Enable the power save mode with motion sensor Using the provided software 2.
Use of the Functions Alarm SMS The Alarm SMS are alarm messages sent (if the function was enabled) to a phone number every time that: • • • • • • • • the tracker battery is almost discharged the tracker memory is full the GPRS network is available the GPRS network is not available the GPS signal has been lost the GPS signal has been restored the tracker motion is revealed the tracker motion stops Programming To use this function, it is necessary to select the desired event item and set the phone number w
Use of the Functions Example of the SMS message displayed on the mobile phone, when the GPRS network is available GEO,ID:GLORIA,GPRS OK,07/04/10,10:09 Example of the SMS message displayed on the mobile phone, when the GPRS network is not available GEO,ID:GLORIA,GPRS OFF,07/04/10,10:09 Example of the SMS message displayed on the mobile phone, when there is GPS signal GEO,ID:GLORIA,GPS FIX OK,07/04/10,10:09 Example of the SMS message displayed on the mobile phone, when the GPS signal has been lost GEO,ID:GLO
Reading and Writing SMS Commands Reading and Writing SMS Commands The SMS commands allows to set or read some tracker settings. These messages can be sent by a mobile phone or by a GSM device able to send/receive SMS (i.e. a GSM modem). When the tracker is switched on and there is GSM signal, it can receive any SMS command. If the tracker receives a correct SMS command, an answer is sent to the SMS command sender. If the message contains invalid characters, the tracker will not reply.
Reading and Writing SMS Commands Reading Commands Command rpos Meaning and Values Read instantaneous GPS position data. The tracker can reply in 3 different ways: A) POS: = GPS position in real time. B) LAST POS: = no GPS signal. The reply message contains the last detected GPS data. C) POS: NO GPS DATA = from the tracker switching on, the GPS signal has not been detected.
Reading and Writing SMS Commands Command rposc rms rgf ranc Meaning and Values Example Read cyclic position SMS setup and power save mode status. [status: 0=disabled, 1=enabled] [rate: 01÷99 minutes] [power save mode: 0=disabled, 1=enabled] Command: Reply: Read the accelerometer setup values. [sensitivity: 00=disabled sensor, 01=maximum, 10=minimum] [timeout: 01÷99 minutes] Command: Reply: Read the Geofence setup.
Reading and Writing SMS Commands Writing Commands Command wposc Meaning and Values Set the cyclic position SMS in text format and the relevant power save mode. [enabling: 0=disable, 1=enable] [rate: 01÷99 minutes] [power save mode: 0=disable, 1=enable] NOTE: the power save mode works only with SMS rate 5 minutes. Never set like this: wposc=0,xx,1 NOTE: to enable or disable only the cyclic position SMS, send the wposc command with the first field only. In this case, the previously set rate is considered.
Reading and Writing SMS Commands Command wgf Meaning and Values Set the Geofence. [enabling: 0=disable, 1=enable] [LAT1,LONG1,LAT2,LONG2=latitude and longitude for the 2 points defining the Geofence area] NOTE: to enable or disable the Geofence function without setting the area, send the wgf command with the first field only. In this case, the previously set area is considered. Example Case A Command: wgf=1,45g37.7980N,008g28.8012E, 45g37.8970N,008g28.8012E Reply: wgf=1,45g37.7980N,008g28.8012E, 45g37.
Reading and Writing SMS Commands Command wanc Meaning and Values Set the Anchor. [enabling: 0=disable, 1=enable] [radius: 0050, 0100, 0200, 0300, 0500, 0700, 1000, 1500, 2000, 3000, 4000 m; default radius: 0100] NOTE: to set the tracker current position as area center point, send the complete wanc command, containing both enabling and radius fields (e.g. wanc=1,0100). NOTE: to enable or disable the Anchor function without setting the radius, send the wanc command with the first field only.
Reading and Writing SMS Commands Command wgprs Meaning and Values Set the GPRS parameters and start the continuous GPRS connection. [setup: 0=set the GPRS parameters without starting the connection, 1=connect with the new parameters (IP, PORT), 2=connect with the parameters previously preset] [parameters: IP=host IP address, PORT=TCP port] NOTE: the IP and PORT parameters should be written between commas. NOTE: if there is no GPRS connection, the tracker sends an error SMS containing “GPRS ERROR”.
Troubleshooting Troubleshooting In this chapter, the answers to the most frequently asked questions. Problem Possible causes Solutions The tracker doesn’t switch on. Key pressed too quickly or too lightly . Press the key down Discharged battery. Charge the battery. Dirty battery terminals. Clean the terminals. Battery not working. Replace the battery. Room temperature too high or low. Charge at a room temperature suitable for the tracker. Dirty battery terminals. Clean the terminals.
Troubleshooting Problem Absence of network service. Impossible to make a call. Impossible to send an SMS. Possible causes Solutions Weak or no signal. Move to an area with signal coverage. SIM card not valid. Contact network service provider. Network too busy. Try again later. Run out of credit. Top up credit. Run out of credit. Top up credit. The SMS Center number is incorrect. Set the SMS Center number on the SIM card by means of a mobile phone.
Maintenance Maintenance The tracker and relevant accessories must be handled with care. Read the following instructions carefully. • Clean the tracker with a soft cloth, avoiding the use of corosive chemical products, solvents or aggressive detergents. • Do not paint the tracker. • Do not swallow the accessories or small components of the tracker. • Avoid blows to the tracker which could internally damage the product. • Do not open the tracker in any way differently from the way indicated in the manual.
Manufacturer’s Limited Warranty Manufacturer’s Limited Warranty This warranty does not limit the user’s (statutory) rights under applicable national laws relating to the sale of consumer products. During the warranty period, the Manufacturer or Manufacturer authorized service company will in a commercially reasonable time remedy defects in materials, design and workmanship free of charge by repairing.
Manufacturer’s Limited Warranty How to get Warranty Service In the event of a Product (or accessories ) defect, please return it to a service company authorized by the Manufacturer or to the Manufacturer himself.
Manufacturer’s Limited Warranty This Limited Warranty does not cover: • normal wear and tear of the Product (including, without limitation,wear and tear of batteries or displays) • defects caused by rough handling (including, without limitation, defects caused by sharp items, by bending, compressing or dropping, etc.) • defects or damage caused by misuse of the Product, including use that is contrary to the instructions provided by the Manufacturer (e.g.
Manufacturer’s Limited Warranty Other Important Notices A third party, independent operator provides the SIM card and and/or other network or system on which the Product operates. Therefore, the manufacturer will not accept responsibility under this warranty for the operation, availability, coverage, device services or other network or system.
Manufacturer’s Limited Warranty Limitation of the Manufacturer’s Liability This Limited Warranty is your sole and exclusive remedy against the Manufacturer and the Manufacturer’s sole and exclusive liability in respect of defects in the Product.
Distributed by www.cte.
