USER MANUAL SHDTU03-ET10R SHDSL Router With 1-Port Ethernet Switch SHDTU03-ET10RS SHDSL Router With 4-Port Ethernet Switch
CTC Union Technologies Co., Ltd. Far Eastern Vienna Building Neihu Technology Park 8F, No. 60 ZhouZi St. Neihu, Taipei, 114 Taiwan SHDTU03-ET10R SHDSL Router With 1-Port Ethernet Switch, SHDTU03-ET10RS SHDSL Router With 4-Port Ethernet Switch, Installation and Operation Manual Version 3.0 Revision Marks Revision Date Notes V 2.0 N/A Software: Version: 1.5X7001r-XAT0 V 3.0 June 6, 2003 Software Version: 1.70XAF0.M2R (1.70XAF0.M2R-H62.
Table of Contents Chapter 1. Introduction … ..… … … ..… … .................... 1.1 General … … … … ...… ...… … … … … .… … … … … … … … 1-1 1.2 Features… … … … … ...… … … … … … … … … … … … … … 1-2 1.3 Specification … … … … .… … … … … … … … … … … … … .. 1-3 1.4 Front Panel … … … … … … … … … … … … … … … … … … . 1-6 1.5 Rear Panel … … … .… ...… … … … … … … … … … … … … .. 1-7 Chapter 2. Configuration … … … … .… .… … … … ..… . 2.1 Configuration of the router … ...… … … … … … … … … … 2-1 1.
Table of Contents Chapter 4. Administration … … … ..… … .................... 4.1 Security … … … … … ..… ...… … … … … … … … … … … … 4-1 4.2 SNMP… … … … … … … … … … … … … … … … … … … … 4-2 4.3 Time Sync … … … … .… … ..… … … … … … … … … … … .. 4-4 Chapter 5. Utility … … … … … … … ..… … .................... 5.1 System Info … … … … … ...… … … … … … … … … … … … 5-1 5.2 Config Tool..… ..… … … … … … … … … … … … … … … … 5-1 5.3 Upgrade … … … .… … .… … … … … … … … … … … … … .. 5-2 5.4 Logout … … ..… .… … .
Table of Contents Chapter 8. Configuration Commands .… … … … ..… . 8.1 Status… … … .… … … ..… ...… … … … … … … … … … … … 8-2 8.2 Show… … … … ..… … … … … … … … … … … … … … … … 8-2 8.3 Write … … … … … ..… ..… … … … … … … … … … … … … .. 8-2 8.4 Reboot … … … … … ..… … … … … … … … … … … … … … . 8-3 8.5 Ping… … … … … … … … … … … … … … … … … ...… … … .. 8-3 8.6 Administration … … … … ...… … … … … … … … … … … … 8-3 8.7 Utility… … … … ..… … … … … … … … … … … … … … … … 8-8 8.8 Exit ..… ..… … … … … … … … … … … .
Table of Contents iv
Chapter 1. Introduction 1.1 General You are about to join the new ranks of G.SHDSL technology. Your new G.SHDSL Router is an external Single-Pair High-Speed Digital Subscriber Line (SHDSL) Router, which conveniently connects with a Switch, Hub or computer. The Router connects directly to telephone line via a standard RJ11 connector. The SHDSL (Single-Paired High Speed Digital Subscriber Line) router complies with G.992.2 standard and connects to any Ethernet LAN utilizing 10/100 Base-T auto-negotiation.
Chapter 1. Introduction 1.
Chapter 1. Introduction 1.3 Specifications Routing ? ? ? ? ? ? ? Support IP/TCP/UDP/ARP/ICMP/IGMP protocols IP routing with static routing and RIPv1/RIPv2 (RFC1058/2453) IP multicast and IGMP proxy (RFC1112/2236) Network address translation (NAT/PAT) (RFC1631) NAT ALGs (Application Level Gateway) for ICQ/Netmeeting/MSN/Yahoo Messenger DNS relay and caching (RFC1034/1035) DHCP server (RFC2131/2132) Bridging ? IEEE 802.
Chapter 1. Introduction AAL5 Encapsulation ? VC multiplexing and SNAP/LLC ? Ethernet over ATM (RFC 2684/1483) ? PPP over ATM (RFC 2364) ? Classical IP over ATM (RFC 1577) PPP ? ? ? PPP over Ethernet (RFC 2516) PPP over ATM (RFC 2364) User authentication with PAP/CHAP/MS-CHAP WAN Interface ? SHDSL: ITU-T G.991.
Chapter 1. Introduction Physical/Electrical ? Dimensions: 18.7 x 3.3 x 14.5cm (WxHxD) ? Power: 100~240VAC (via power adapter) ? Power consumption: 6 watts ? Temperature: 0~45 C ? Humidity: 0%~95%RH (non-condensing) Memory ? 2MB Flash Memory, 4MB SDRAM Products’Information SHDTU03/ET10R: G.SHDSL router/bridge with 1-port LAN SHDTU03/ET10RS: G.
Chapter 1. Introduction 1.
Chapter 1. Introduction 1.5 Rear Panel The rear panel of SHDSL router is where all of the connections are made. Rear Panel of SHDTU03/ET10R router with or without firewall Rear Panel of SHDTU03/ET10RS router with or without firewall ! CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
Chapter 1. Introduction ! The reset button can be used in one of two ways. 1. When you want to change the SHDTU03's configuration but you forgot the user name or password, press the Reset Button for three or four seconds with a paper clip or sharp pencil. Pressing the Reset Button in this way will cause the SHDTU03 to load the factory default settings and lose all of your configuration. 2.
Chapter 2. Configuration 2.1 C onfiguration of the Router This guide is designed to lead users through Web Configuration of SHDTU03/ET10R Router in the easiest and quickest way possible. Please follow the instructions carefully. Note: There are three methods to configure the router: serial console, Telnet and Web Browser. Only one configuration application is used to setup the Router at any given time. Users have to choose one method to configure it. For Web configuration, you can skip to step 3.
Chapter 2. Configuration Step 4: Determine Connection Setting Users need to know the Internet Protocol supplied by your Service Provider and determine the mode of setting. Protocol Selection RFC1483 Bridged Ethernet over ATM RFC1577 Classic Internet Protocol over ATM RFC2364 Point-to-Point Protocol over ATM RFC2516 Point-to-Point Protocol over Ethernet The different Protocols need to setup different WAN parameters.
Chapter 2.
Chapter 2. Configuration Step 5: Install the SHDSL Router Caution: To avoid possible damage to this Router, do not turn on the router before Hardware Installation. ? Connect the power adapter to the port labeled DC-IN on the rear panel of the product. ? Connect the Ethernet cable. ?If the 1-port router is directly connected to PC or NB, the Ethernet cable must use a cross over cable. If the 1-port router is connected to hub or switch, be sure that the hub or switch supports auto-sensing.
Chapter 2.
Chapter 2. Configuration Server Storage Server Wireless Access Point Wireless Note Book Workstation Switching Hub Mobile Device Laser Printer PC Power Adapter Wall Jack PC G.shdsl RJ-11 DB-9 Cable 4-port router with complex network topology 2.2 Configuration via Web Browser For Win85, 98 and Me, click the start button. Select setting and control panel. Double click the network icon.
Chapter 2. Configuration In the Configuration window, select the TCP/IP protocol line that has been associated with your network card and then click the properties button. Choose the IP Address tab. Select Obtain an IP address automatically. Click the OK button.
Chapter 2. Configuration The window will ask you to restart the PC. Click the Yes button. When the PC has restarted, Open Internet Explorer or Netscape Browser to connect to the Router. Type http://192.168.0.1 The default IP address and sub netmask of the Router is 192.168.0.1 and 255.255.255.0. Because the router acts as DHCP server in your network, the router will automatically assign an IP address for the PC or NB on the network. Type User Name root and Password root and then click OK.
Chapter 3. Set-Up 3.1 Basic (Quick Setup) The Basic Setup contains Bridge and Route operation modes. Follow this example to set Bridge mode Click Basic for basic installation. Bridge Mode IP: 192.168.0.1 Netmask: 255.255.255.0 Gateway: 192.168.0.254 Bridge PC IP: 192.168.0.2 Netmask: 255.255.255.0 Gateway: 192.168.0.254 BAS IP: 192.168.0.254 DSLAM VPI:0, VCI:32 Encapsulation: LLC Click Bridge and CPE Side to setup Bridging mode of the Router and then click Next for the next setting.
Chapter 3. Set-Up The screen will prompt with the new configuration parameters. Check the parameters and Click Restart The router will reboot with the new settings or Continue to configure other parameters. Routing Mode Routing mode contains settings for DHCP server, Point-to-Point Protocol over ATM and Ethernet, IP over ATM and Ethernet over ATM. You need to clarify which Internet protocol is provided by your ISP. Click ROUTE and CPE Side then press Next. Type LAN parameters: IP Address: 192.168.0.
Chapter 3. Set-Up DHCP Server Dynamic Host Configuration Protocol (DHCP) is a TCP/IP Suite protocol that allows network administrators to manage and automate centrally the assignment of Internet Protocol (IP) addresses in an organization's network. Using the Internet Protocol, each machine that wishes to connect to the Internet needs a unique IP address. When an organization sets up its computer users with a connection to the Internet, a unique IP address must be assigned to each machine.
Chapter 3. Set-Up PPPoE or PPPoA PPPoA (point-to-point protocol over ATM) and PPPoE (point-to-point protocol over Ethernet) are authentication and connection protocols used by many service providers for broadband Internet access. These are specifications for connecting multiple computer users on an Ethernet local area network to a remote site through common customer premises equipment, which is the telephone company's term for a customer's modem or similar devices.
Chapter 3. Set-Up Type the ISP1 parameters. ?Username and password are provided by your ISP. Username: test Password: test Password Confirm: test Idle Time: 10 Click Next. ?For security, the password will be displayed with star symbols. The screen will prompt with the parameters to be written in Flash. Check the parameters before writing to Flash. Press Restart to restart the router with the new configuration or press continue to setup other parameters.
Chapter 3. Set-Up IPoA or EoA WAN LAN Router IP: 192.168.0.1 Netmask: 255.255.255.0 IP: 10.1.2.1 Netmask: 255.255.255.0 Gateway: 10.1.2.2 DNS: 168.95.1.1 BAS IP: 10.1.2.2 Netmask: 255.255.255.0 DSLAM PC IP: 192.168.0.2~51 Netmask: 255.255.255.0 Gateway: 192.168.0.1 ISP VPI:0, VCI:33 Encapsulation: LLC Type the Wan Parameters; VPI: 0 VCI: 33 AAL5 Encap: LLC Protocol: IPoA , EoA , IPoA + NAT or EoA + NAT Click Next to setup the IP parameters.
Chapter 3. Set-Up 3.2 Advanced Set-Up Advanced setup contains the configuration steps for SHDSL, WAN, Bridge, Route, NAT/DMZ, Virtual server and firewall parameters. SHDSL You can setup the Annex type, data rate and SNR margin for SHDSL parameters in SHDSL. Click SHDSL Annex Type: There are two Annex types supported, Annex A and Annex B, in SHDSL. Data Rate: you can setup the SHDSL data rate in multiples of 64kbps. SHDSL SNR margin: the margin range is from 0 to 10.
Chapter 3. Set-Up WAN The SHDSL router supports up to 8 PVCs. The parameters are setup under WAN. The WAN Number 1 will be the parameters setup in Basic Setup. If you want to setup another PVC, you may configure them in WAN 2 to WAN 8. Enter the parameters. Press Finish to finish setting. The screen will prompt with the parameters that will be written to Flash. Check the parameters before writing to Flash.
Chapter 3. Set-Up Bridge The bridge mode can be setup with static bridge parameters. Click Bridge to setup. Press Add to add the static bridge information. The screen will prompt with the parameters that will be written to Flash. Check the parameters before writing to Flash. Press Restart to restart the router with new the configuration or press continue to setup other parameters.
Chapter 3. Set-Up VLAN Virtual LAN (VLAN) is defined as a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLAN is based on logical instead of physical connections, it is extremely flexible. The IEEE 802.
Chapter 3. Set-Up Click VLAN to configure VLAN. The SHDTU03 supports two types of VLAN, 802.1Q and Port-Based. The user can configure either one of them in the router. For setting 802.1Q VLAN click the 802.1Q Tag-Based VLAN. The screem will prompt as follows. VID: Virtual LAN ID. Is a defined number, an ID which numbers from 1 to 4094. PVID: Port VID is an untagged member of default VLAN. Link Type: Access means the port can send or receive untagged packets.
Chapter 3. Set-Up If the SHDTU03 works in bridge mode, the Link type of WAN will be Trunk, tagged port, and you can assign any PVID to WAN except 0 and leaving blank. When the SHDTU03 works under routing mode, the Link Type of WAN will be Access mode, un-tagged port. Port-Based VLANs are VLANs where the packet forwarding decision is based on the destination MAC address and its associated port. Click Port-Based VLAN to configure the router.
Chapter 3. Set-Up LAN1 LAN2 LAN3 LAN4 WAN Group 1 Group 2 Group 3 No LAN1 LAN2 LAN3 LAN4 WAN 1 ? ? ? ? ? 2 ? ? ? ? ? 3 ? ? ? ? ? 4 ? ? ? ? ? 5 ? ? ? ? ? Route If the Router is connected to more than one network, it may be necessary to set up a static route between them. A static route is a predetermined pathway that network information must travel to reach a specific host or network.
Chapter 3. Set-Up Click Route to modify the routing information. To modify the RIP (Routing information protocol) Parameters: RIP Mode: Enable Auto RIP Summary: Enable Press Modify RIP Mode: this parameter determines how the product handles RIP (Routing information protocol). RIP allows it to exchange routing information with other routers. If set to Disable, the gateway does not participate in any RIP exchange with other routers.
Chapter 3. Set-Up RIP Version: This determines the format and broadcasting method of any RIP transmissions by the gateway. RIP v1: it only sends RIP v1 messages only. RIP v2: it send RIP v2 messages in multicast and broadcast format. Authentication required. None: for RIP, there is no need for an authentication code. Password: the RIP is protected by password, authentication code. MD5: The RIP will be decoded by MD5 then protected by password, authentication code.
Chapter 3. Set-Up NAT/DMZ NAT (Network Address Translation) is the translation of an Internet Protocol address (IP address) used within one network to a different IP address known within another network. One network is designated as the inside network (private) and the other as the outside network (public). Typically, a company maps its local inside network addresses to one or more global outside IP addresses and reverses the global IP addresses of incoming packets back into local IP addresses.
Chapter 3. Set-Up If you want to enable the NAT/DMZ functions, click Enable. Enable the DMZ host Function will use the IP address assigned to the WAN for enabling DMZ function for the virtual IP address. Multi-DMZ: Some users who have two or more global IP addresses assigned by ISP can use the multi DMZ function. The table is for the mapping of global IP address and virtual IP address. Multi-NAT: Some of the virtual IP addresses (eg: 192.168.0.10 ~ 192.168.0.
Chapter 3. Set-Up Virtual Server For example: Specific ports on the WAN interface are re-mapped to services inside the LAN. As an example, only 69.210.1.8 (e.g., assigned to WAN from ISP) is visible to the Internet, but does not actually have any services (other than NAT of course) running on gateway. It is said to be a virtual server. Request with TCP made to 69.210.1.8:80 are remapped to the server 1 on 192.168.0.2:80 for working days from Monday to Friday 8 AM to 6PM, other requests with UDP made to 69.
Chapter 4. Administration This session introduces security, simple network management protocol (SNMP) and time synchronization. Security For system security, it is suggested to change the default user name and password after the first setup, otherwise unauthorized persons may gain access to the router and change the parameters. There are three ways to configure the router, Web browser, Telnet and serial console. Press Security to setup the parameters.
Chapter 4. Administration SNMP Simple Network Management Protocol (SNMP) is the protocol not only governing network management, but also for the monitoring of network devices and their functions. The router can generate SNMP traps to indicate alarm conditions, and it relies on SNMP community strings to implement SNMP security. This router support MIB II. Click SNMP to configure the parameters. In the table of current community pool, you can setup the access authority.
Chapter 4. Administration SNMP status: Enable Access Right: Deny for deny all access Access Right: Read for access read only Access Right: Write for access read and write. Community: it serves as password for access right. After configuring the community pool, press OK. Click Modify to modify the trap host pool. Version: select version for trap host. IP: type the trap host IP Community: type the community password. Press OK to finish the setup. The browser will prompt with the configuration parameters.
Chapter 4. Administration Time Sync Time synchronization is an essential element for any business that relies on an IT system. The reason for this is that these systems all have clocks that are the source of time for files or operations they handle. Without time synchronization, time on these systems varies with each other or with the correct time and this can cause, firewall packet filtering schedule processes to fail, security to be compromised, or system log exposures with wrong data. Click TIME SYNC.
Chapter 5. Utility This section describes the utility to display the system information, load the factory default configuration, upgrade the firmware and restart the gateway. System Info Click System Info to review the system information. The browser will prompt for the system information. Config Tool This configuration tool has three functions: load Factory Default, Restore Configuration and Backup Configuration. Press Config Tool. Choose the function you wish to perform and then press finish.
Chapter 5. Utility Upgrade You can upgrade the gateway using the upgrade function. Press Upgrade. Browse to the file and press the OK button to upgrade. The system will reboot automatically after finishing. Do not allow any power disruption during the upgrade process. Logout To logout of the router, press logout.
Chapter 5. Utility Restart For restarting the router, click the Restart item under UTILITY. Press Restart to reboot the router.
Chapter 5. Utility This page was left blank intentionally.
Chapter 6. Status You can monitor the SHDSL status including mode, Tx power and Bitrate and Performance information including SNR margin, attenuation and CRC error count. LAN status will display the MAC address, IP address, Subnet mask and DHCP client table. WAN status will display the WAN interface information. You can view the routing table from the "ROUTE" status. "INTERFACE" status includes LAN and WAN statistics information.
Chapter 6. Status CO side Click Bridge and CO Side to setup Bridging mode of the Router and then click Next. LAN Parameters Enter IP: 192.168.0.1 Enter Subnet Mask: 255.255.255.0 Enter Gateway: 192.168.0.1 Enter Host Name: SOHO WAN1 Parameters Enter VPI: 0 Enter VCI: 32 Click LLC Click Next The screen will prompt with the new configuration parameters. Check the parameters and Click Restart The router will reboot with the new settings.
Chapter 6. Status CPE Side Click Bridge and CPE Side to setup Bridging mode of the Router and then click Next. LAN Parameters Enter IP: 192.168.0.2 Enter Subnet Mask: 255.255.255.0 Enter Gateway: 192.168.0.2 Enter Host Name: SOHO WAN1 Parameters Enter VPI: 0 Enter VCI: 32 Click LLC Click Next The screen will prompt with the new configuration parameters. Check the parameters and Click Restart The router will reboot with the new settings.
Chapter 6. Status LAN-to-LAN connection in routing mode STU-C (CO) STU-R (CPE) Router IP: 192.168.20.1 Netmask: 255.255.255.0 Router IPoA or EoA VPI:0, VCI:32 Encapsulation: LLC IP: 192.168.30.1 Netmask: 255.255.255.0 Gateway: 192.168.30.2 IP: 192.168.10.1 Netmask: 255.255.255.0 IP: 192.168.30.2 Netmask: 255.255.255.0 Gateway: 192.168.30.1 IP: 192.168.20.100 Netmask: 255.255.255.0 Gateway: 192.168.20.1 IP: 192.168.10.200 Netmask: 255.255.255.0 Gateway: 192.168.10.
Chapter 6. Status Type the Wan Parameters; VPI: 0 VCI: 32 AAL5 Encap: LLC Protocol: IPoA , EoA , IPoA + NAT or EoA + NAT Note: The Protocol used in CO and CPE have to be the same. Click Next to setup the IP parameters. For more understanding about NAT, review NAT/DMZ in page 19. IP Address: 192.168.20.1 Subnet mask: 255.255.255.0 Gateway: 192.169.30.2 Click Next The screen will prompt with the parameters that will be written in Flash. Check the parameters before writing to Flash.
Chapter 6. Status CPE side Click ROUTE and CPE Side then press Next. Type LAN parameters: IP Address: 192.168.10.1 Subnet Mask: 255.255.255.0 Host Name: SOHO DHCP Service: For more DHCP service, review DHCP Service. Type the Wan Parameters; VPI: 0 VCI: 32 AAL5 Encap: LLC Protocol: IPoA , EoA , IPoA + NAT or EoA + NAT Note: The Protocol used in CO and CPE have to be the same. Click Next to setup the IP parameters. For more understanding of NAT, review the NAT/DMZ section in this manual. IP Address: 192.168.
Chapter 7. Serial Console or Telnet Mode Serial Console Check the connectivity of the RS-232 cable from your computer to the serial port of the ROUTER. Start your terminal access program with VT100 terminal emulation. Configure the serial link with baudrate of 9600, 8 data bits, no parity check, 1 stop bit, and no flow-control, and press the SPACE key until the login screen appears. When you see the login screen, you can logon to Router.
Chapter 7. Serial Console or Telnet Mode Window structure From top to bottom, the window will be divided into four parts: 1. Product name 2. Menu field: Menu selection items are prompted on this field. The “>>” symbol indicates the cursor position. 3. Configuration field: You will configure the parameters in this field. < parameters > indicates the parameters you can choose and < more… > indicates that there is another submenu in the title. 4.
Chapter 7. Serial Console or Telnet Mode Menu Driven Interface Commands Before changing the configuration, familiarize yourself with the navigation keys listed in the following table. The operation list will be shown on the window. Keystroke [UP] or I [DOWN] or K [LEFT] or J [RIGHT] or L [ENTER] [TAB] Ctrl + C Ctrl + Q Description Move to field above in the same level menu. Move to field below in the same lever menu. Move back to previous menu. Move forward to submenu. Move forward to submenu.
Chapter 7. Serial Console or Telnet Mode Menu Tree All of the configuration commands that are placed in the subdirectories of Enable are protected by supervisor password. User Name & Password Enable Enable Setup Mode SHDSL WAN Bridge Route LAN IP-share DHCP DHCP-proxy Hostname Default Status SHDSL WAN Route Interface Show System Config Script Write Reboot Ping Admin User Security SNMP
Chapter 7. Serial Console or Telnet Mode Setup Mode SHDSL Mode n*64 Type Clear Margin WAN Protocol Address VPI_VCI Encap QoS Class PCR ISP List Bridge Gateway Static Add Delete Modify List Route Static MAC LAN_Port WAN1_Port WAN8_Port Add Delete List RIP Generic LAN Attrib Version Authetication WAN LAN Version Attrib Authetication List IP-share NAT PAT DHCP DHCP-proxy Attrib Address DMZ Generic Fixex List
Chapter 7. Serial Console or Telnet Mode Setup Mode SHDSL WAN Bridge Route LAN
Chapter 7.
Chapter 7. Serial Console or Telnet Mode This page was left blank intentionally.
Chapter 8. Configuration Commands To setup the router, move the cursor “ >>” to enable and press the enter key. When the screen appears, type the supervisor password. The default supervisor password is root. The password will be written on screen as “ * “ symbol for system security. ---------------------------------------------------------------------Command: enable Message: Please input the following information.
Chapter 8. Configuration Commands Status You can view the running system status of SHDSL, WAN, route and interface via the status command. Move cursor “ >> “ to status and press enter. >> shdsl wan route interface Show Show Show Show SHDSL status WAN interface status routing table interface statistics status Show You can view the system information, configuration and configuration in command script with the show command. Move cursor “ >> “ to show and press enter.
Chapter 8. Configuration Commands Reboot To reboot the router, use the reboot command. Move the cursor to “ >> “ to reboot and press enter. ----------------------------------------- ----------------------------Command: reboot Message: Please input the following information. Do you want to reboot? (y/n): y ---------------------------------------------------------------------- Ping Ping command will be used to test the connection of the router. Move the cursor “ >> “ to ping and press enter.
Chapter 8. Configuration Commands User Profile You can use the user command to clear, modify and list all the user profiles. You can setup up to five users to access the router via console port or Telnet in the user profile table. However users who have the supervisor password can change the configuration of the router. Move the cursor “ >> “ to user and press enter key.
Chapter 8. Configuration Commands Security Security command can be used to configure ten legal IP address for Telnet access and port number. Move the cursor “ >> “ to security and press enter. The default legal address is 0.0.0.0. which means that there is no restriction of IP to access the router via Telnet.
Chapter 8. Configuration Commands 5 SNMP trap entry can be configured in this system. Move the cursor to trap and press enter. ---------------------------------------------------------------------Command: admin snmp trap <1~5> Message: Please input the following information.
Chapter 8. Configuration Commands To configure SNTP v4 time synchronization, follow the procedures below. move the cursor to method and press enter. ---------------------------------------------------------------------Command: admin sntp method Message: Please input the following information. SYNC method (Enter for default) : SNTPv4 ---------------------------------------------------------------------- Move the cursor to service and press enter.
Chapter 8. Configuration Commands Move the cursor to time_zone and configure where your router is placed. The easiest way to know the time zone offset hour is from your PC clock. Double click the clock at the right corner of monitor and check the time zone. ---------------------------------------------------------------------Command: admin sntp time_zone < -12~12> Message: Please input the following information.
Chapter 8. Configuration Commands Setup All of the setup parameters are located in the subdirectories of setup. Move the cursor “ >> “ to setup and press enter.
Chapter 8. Configuration Commands SHDSL You can setup the SHDSL parameters by using the command shdsl. Move the cursor “ >> “ to shdsl and press enter. >> mode n*64 type clear margin Configure SHDSL mode Configure SHDSL data rate Configure SHDSL annex type Clear current CRC error count Configure SHDSL SNR margin There are two types of SHDSL modes, STU-C and STU-R. STU-C means the terminal of central office and STU-R customer premises equipment.
Chapter 8. Configuration Commands WAN The router supports 8 PVC, private virtual circuit, and so you can setup eight WANs; WAN1 to WAN8. Move the cursor “ >> “ to wan and press enter. To setup WAN1, type 1. ---------------------------------------------------------------------Command: setup wan <1~8> Message: Please input the following information.
Chapter 8. Configuration Commands Bridge You can setup the bridge parameters using the bridge command. If the product is configured as a router, you do not need to setup the bridge parameters. Move the cursor “ >> “ to bridge and press enter. >> gateway static Default gateway Static bridging table You can setup the default gateway IP via the gateway command. You can setup 20 sets of static bridge in static command.
Chapter 8. Configuration Commands VLAN Virtual LAN (VLAN) is defined as a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLAN is based on logical instead of physical connections, it is extremely flexible. The specification of VLAN function is as follow: 1.
Chapter 8. Configuration Commands To activate the VLAN function, move the cursor “ >> “ to mode and press enter. The products support two types of VLAN, 802.11Q and Port-Based. The IEEE 802.1Q defines the operation of VLAN bridges that permit the definition, operation, and administration of VLAN topologies within a bridged LAN infrastructure. Port-Based VLANs are VLANs where the packet forwarding decision is based on the destination MAC address and its associated port. 802.
Chapter 8. Configuration Commands To assign PVID (Port VID), move the cursor “ >> ” to PVID and press enter. The port index 1 to 4 represents LAN1 to LAN4 respectively and port index 5 represents WAN. VID value is the group at which you want to assign the PVID of the port. ---------------------------------------------------------------------Command: setup vlan pvid <1~5> <1~4094> Message: Please input the following information.
Chapter 8. Configuration Commands If the Router is connected to more than one network, it may be necessary to set up a static routes between them. A static route is a pre-determined pathway that network information must travel to reach a specific host or network. With Dynamic Routing, you can enable the Router to automatically adjust to physical changes in the network’s layout.
Chapter 8. Configuration Commands The SHDTU03 supports 8 PVCs and you can configure the RIP parameters of each WAN via the wan command. Move the cursor “ >> ” to wan and press enter. ---------------------------------------------------------------------Command: setup route rip wan <1 ~8> Message: Please input the following information.
Chapter 8. Configuration Commands NAT (Network Address Translation) is the translation of an Internet Protocol address (IP address) used within one network to a different IP address known within another network. One network is designated the inside (private) network and the other is the outside (public) network. Typically, a company maps its local inside network addresses to one or more global outside IP addresses and reverse the global IP addresses of incoming packets back into local IP addresses.
Chapter 8. Configuration Commands You can delete virtual IP address range- from 1 to 5- by using the delete command. You can view the virtual IP address range via the list command. To setup global IP address pool, move the cursor “>>” to global command and press enter. >> range interface delete list Edit global IP address pool Bind address pool to specific interface Delete global IP address pool Show global IP address pool You can create five global IP address pool range via range command.
Chapter 8. Configuration Commands To modify the fixed IP address mapping, move the cursor “>>” to the fixed command and press enter. >> modify interface delete list Modify fixed NAT mapping Bind address pair to specific interface Delete fixed NAT mapping Show fixed IP address mapping You can create up to 10 fixed NAT mapping entries via the range command.
Chapter 8. Configuration Commands PAT To configure Port Address Translation, move the cursor “>>” to the pat command and press enter. >> clear modify list Clear virtual server mapping Modify virtual server mapping Show virtual server mapping pool You can delete virtual server mapping entries- from 1 to 10- by using the clear command. You can create up to 10 virtual server mapping entries via the modify command.
Chapter 8. Configuration Commands DMZ To setup demilitarized zone, move the cursor “>>” to dmz and press enter. >> active address Tigger DMZ host function Configure virtual IP address and interface You can enable the demilitarized zone via the active command. After enabling the DMZ, shift the cursor to address and press enter. ---------------------------------------------------------------------Command: setup ip_share dmz address <1~10> Message: Please input the following information.
Chapter 8. Configuration Commands To configure the DHCP server, move the cursor to dhcp and press enter. >> generic fixed list Configure generic DHCP parameter s Configure fixed host IP address list Show DHCP configuration The generic DHCP parameters can be configured via the generic command.
Chapter 8. Configuration Commands DNS proxy You can setup three DNS servers in the product. The number 2 and 3 DNS servers are optional. Move the cursor “ >> “ to dns_proxy and press enter. ------------------------------------------ ---------------------------Command: setup dns_proxy [IP] [IP] Message: Please input the following information. DNS server 1 (ENTER for default) <168.95.1.1>: 10.0.10.1 DNS server 2: 10.10.10.
Transmission Units CTC Union Technologies Co., Ltd. Far Eastern Vienna Building (Neihu Technology Park) 8F, No. 60, ZhouZi St., Nei-Hu, Taipei, Taiwan Phone:(886) 2.2659.1021 Fax:(886) 2.2799.1355 E-mail: info@ctcu.com http://www.ctcu.
