Product specifications

Chapter 3 Configuration and Operation
16
CLI Command Descriptions
CLICommand Descriptions
SystemCommands
logout LogoutfromtheCLISystem
cdisp DisplayIPM‐4SEcurrentconfigurations.
csave Savecurrentconfigurations:IPM‐4SE&relativesettings.
cload LoadconfigurationsettingfromFLASH.
reboot Rebootcommandtouseaftersavingconfiguration
passwd
Enterpasswordtochangeuser‐mode.(i.e.View/Setup/Adminmode)
PS:Ifinputtedpasswordisnotfor"setup"or"admin",itwillenterthe"view"mode.
setpassmode
Modifypasswordforuser‐mode.
mode:‘s’forsetupmode,‘a’foradminmode.
ipsetip_addrnet_maskgateway_ip
SetIPM‐4SEIPaddress,netmaskandgatewayIPaddress.
ip_addr:IPAddress,net_mask:netmask,gateway_ip:gatewayIP.
EX:ipset192.168.1.28255.255.255.0192.168.1.254
ipget GetIPM‐4SEcurrentIPaddress,netmask,andgatewayIPaddress.
trapsetmodetrap_ip_addr
SetSNMPTrapMode&HostIP
mode:0fordisablingSNMPtrap,1forenablingSNMPtrap
EX:trapset1192.168.6.3(enablestrapsendingto192.168.6.3manager)
trapget GetSNMPTrapMode&HostIP
ntpsetmodeserver_ip_addr
SetNTPEnableMode&NTPServerIP
mode:0fordisableNTPfunction,1forenableNTPfunction
ntpget GetNTPEnableMode&NTPServerIP
upgradeserver_ipfile_name
UpgradeSoftwareimagefilefromTFTPserver
server_ip:TFTPserverIPaddress
file_name:SWimagefilename
EX:upgrade192.168.2.199ipm130.bin
backuptftp_server_ipfile_name
BackupthesystemconfigurationtoTFTPserver
tftp_server_ip:theTFTPserverIPaddress
file_name:thebackupfilename
EX:backup192.168.2.199ipm4se_co_backup_1
restoretftp_server_ipfile_name
RestorethesystemconfigurationfromTFTPserver
tftp_server_ip:theTFTPserverIPaddress
file_name:thebackupfilename
EX:restore192.168.2.199ipm4se_co_backup_1
tgmodemode
SetTGMode
mode:0forGlobalmode,1forE1‐Indepmode
ceschclksetch_numclksrc
SetChannelTimingGenClockSource
ch_no:E1channelnumber.
clksrc:0:Adaptive(remote),1:Internal,2:E1Recovery,3:Bits.
tgpriset1st.source2nd.source
SetTGClockPrioritySource
source:0:Ext.BITS,1:Global.TG,2:HoldOver,3:FreeRun
tge1loope1_num
SetTGSecondaryClockSourceInput
e1_num:1~4forE1#1~E1#4
tgget GetTGModeandStatus
timesethourminsec Setcurrenttimewith‘hour’,‘minute’and‘second’.
datesetyearmonthday Setcurrentdatewith‘year’,‘mouth’and‘day’
timeget Getcurrenttimeanddate
lpkset ch_no mode enable
Enable/Disable E1 channel loopback mode.
ch_no: E1 channel number.
mode: 0:Disable-All, 1:E1-Remote (FE), 2:E1-Local (NE)
enable: 0:disable, 1:enable.
EX: lpkset 1 1 1
lpkget Get current loopback mode of E1 channel.
ping ip_addr
Use ICMP to check connection
EX: ping 192.168.1.28